Contact Us

TMP107BIDR

Brand: Texas Instruments
Texas Instruments TMP107BIDR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMP107BIDR — Power Management & Signal Chain | Superb Automation

TMP107BIDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMP107BIDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMP107BIDR: temperature sensing on a one wire daisy chain

The TMP107BIDR is a digital temperature sensor with a bidirectional UART compatible single wire interface, built to be chained. Up to thirty two devices sit on one bus, each with a unique five bit address held in on chip EEPROM, and the host talks to them in sequence along the chain rather than through a shared two wire bus.

The arrangement suits equipment where the measurement points are spread out: a rack of battery modules, a cabinet with several heat sources, a machine with sensors along its length. One pair of wires runs from device to device, and each device passes the conversation along.

Accuracy is plus or minus 0.4 C maximum from minus 20 to 70 C, plus or minus 0.55 C from minus 40 to 100 C and plus or minus 0.7 C from minus 55 to 125 C. The part is offered in an eight pin SOIC, which is large by modern standards and easy to place and rework.

Key data for the TMP107BIDR

FunctionDigital temperature sensor with a single wire chained interface
BusUART compatible, bidirectional, up to 32 devices in a chain
AddressingFive bit address stored in on chip EEPROM
AccuracyPlus or minus 0.4 C from minus 20 to 70 C, plus or minus 0.7 C from minus 55 to 125 C
Resolution14 bit temperature result
AlertsTwo alert outputs with programmable trip points
EEPROMUsed for addressing, trip points and a user byte
ConversionOne shot mode with the bus inactive between readings
PackageSOIC, 8 pins
Temperature rangeMinus 55 to 125 C operation
OrderingTMP107BIDR, 2500 pieces on a large tape and reel

Why a chain beats a bus in a long enclosure

A two wire bus is a shared line, and every device on it adds capacitance and a stub. Past a few metres and a handful of devices, the edges soften and the bus needs a buffer or a multiplexer. A chained single wire interface passes data through each device in turn, regenerating it, so the length is limited by the number of devices rather than by the capacitance.

That arrangement also fixes the wiring: each sensor has an input and an output, and the chain order is the physical order. A service engineer can tell which sensor is which by its position in the chain, which is easier than reading addresses off a bus.

The trade is that a break in the chain loses every device after it. On a shared bus, one bad connection loses one device. For a battery rack where the modules are inaccessible, that difference decides whether a fault is a service call or a shutdown.

The EEPROM, and what it means for a replacement

Address, trip points and a user byte live in EEPROM inside the device. That means the address is not set by pins or by the board, it is written once during production and stays with the part. Replacing a sensor in the field means writing the same address into the new part, or the chain will have two devices answering to one address.

Trip points also live there, so a sensor that is swapped without programming comes back with default limits. A product that relies on the alert to protect something will find that the protection moved when the sensor was replaced.

Programming in production is therefore part of the build, not an optional step. It is also a step that has to be repeatable across a rework, which means the fixture has to be able to write a single device in place.

Where it fits in a build

Battery racks, telecom cabinets, industrial enclosures and machines with sensing along a frame. The eight pin SOIC is easy to hand place and easy to probe, which matters in equipment that is serviced in the field rather than swapped as a unit.

A chain of sensors is a record of where each part came from, so traceability is worth holding. The sourcing audit trail page covers how a part and its programming record are kept together, and the date code management page covers how reel age is tracked for parts that sit in stores before a build.

The sourcing side of this part is covered on the supplier quality audit. For a sensor that is programmed with an address during production, that page covers what we ask about the programming record.

Questions we get on this code

Can the chain be read while a device is converting? Yes, the interface is bidirectional and the device holds the line only when it is addressed. A conversion in progress does not block a read of another device.

How long can the chain be? The limit is thirty two devices, and the cable length depends on the baud rate and the termination. A long chain at a high rate needs the cable characteristics checked, not just the device count.

Does it need a pull up? The single wire interface is driven by the devices in turn, and the idle state is set by the host. A pull up is normally fitted at the host end, and its value depends on the cable capacitance.

Can it replace an NTC in an existing board? Mechanically yes, and electrically it removes the divider and the table. The board change and the programming step are the parts that a quick comparison usually misses.