Contact Us

TMP1075NDRLR

Brand: Texas Instruments
Texas Instruments TMP1075NDRLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMP1075NDRLR — Power Management & Signal Chain | Superb Automation

TMP1075NDRLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMP1075NDRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMP1075NDRLR: an LM75 footprint sensor with modern accuracy

The TMP1075NDRLR is a digital temperature sensor in a six pin SOT563 body measuring 1.60 mm by 1.60 mm, with an I2C and SMBus interface and a register map that follows the long established LM75 pattern. It is the N version of the family, which runs from 1.62 V to 3.6 V and offers four bus addresses instead of the thirty two of the wider supply members.

Accuracy is plus or minus 0.25 C typical from minus 55 to 125 C, and plus or minus 1 C maximum from minus 40 to 110 C. Average current is 2.7 microamps with a shutdown current of 0.37 microamps, so the part can stay powered on a battery board without a load switch.

The LM75 register map is the reason this part is bought. A board that was laid out for an older sensor can take it without a change to the host code, and the address pins allow several devices to share a bus the way the original allowed.

Key data for the TMP1075NDRLR

FunctionDigital temperature sensor with a two wire interface
Register mapCompatible with the industry standard LM75
AccuracyPlus or minus 0.25 C typical, plus or minus 1 C maximum from minus 40 to 110 C
Resolution12 bit, 0.0625 C per step
Supply1.62 V to 3.6 V on the N version
Current2.7 microamps average, 0.37 microamps shutdown
AddressingFour addresses on the N version, thirty two on the wider supply members
AlertSMBus alert function with programmable limits
ResetSMBus reset support
PackageSOT563, 6 pins, 1.60 mm by 1.60 mm
Temperature rangeMinus 55 to 125 C operation
OrderingTMP1075NDRLR, large tape and reel

The drop in claim, tested rather than assumed

Software compatibility is a statement about registers. It says the pointer values, the data format and the alert behaviour follow the same pattern. It does not say the package is the same, that the supply range is the same, or that the accuracy at the extremes is the same.

A board that is being converted from an older LM75 style part should be checked on four points: the package and pin function, the supply range against the existing rail, the address pin behaviour, and the conversion time at the accuracy the product needs. Any of those four can turn a drop in replacement into a board change.

The N version is the one to watch. Its supply starts at 1.62 V, which is useful on a 1.8 V rail, and it exposes four addresses instead of thirty two. A bus that already carries eight devices cannot take eight of these, and that is a routing problem rather than a software one.

Two point seven microamps, and where it goes

At 2.7 microamps average, a sensor on a coin cell is a rounding error next to the bus pull ups. A 10 kilo ohm pull up pair on a bus that is low half the time draws far more than the sensor, so a product that is chasing standby current should size the pull ups before choosing a lower power sensor.

Shutdown at 0.37 microamps is available through a register write. A host that only needs a reading every minute can put the device down between reads, at the cost of a conversion time at each wake up. For most products the difference is not worth the code.

The conversion time also sets how fast the alert can react. A part that is converting at 8 Hz updates every 125 ms, and an alert that depends on a limit crossing arrives after the conversion that found it. A protection function that needs a faster response belongs in hardware, not in a sensor register.

Where it fits in a build

Telecom boards, servers, industrial controllers and any product that already has an LM75 style sensor in its bill of material. The 1.6 mm package fits where the older SOIC part did not, which is often the real reason for the change.

When a part is bought as a replacement for a device that is going end of life, the comparison has to be documented, because the board was qualified with the old part. The how to verify a drop in replacement page sets out the checks we run, and the supplier quality audit page covers what we ask of the source before a new part number enters a build.

The sourcing side of this part is covered on the incoming inspection plan. For a replacement sensor that carries a register compatibility claim, that page covers the checks we run before the part goes to a line.

Questions we get on this code

Is it pin compatible with an LM75 in SOIC? Not in the same footprint. The register behaviour is compatible, the package is a six pin SOT563, so the board needs a new land pattern.

Does the N version work on a 3.3 V rail? Yes, up to 3.6 V. It does not reach 5.5 V, so a 5 V board needs the standard version.

How many devices on one bus? Four with the N version, thirty two with the wider supply members, within the bus capacitance limit.

Does the alert latch? It can be configured to act as a comparator or as an interrupt that clears on read. The choice is a register bit, and the product behaviour depends on which one is set.