TMP103BYFFR
Product Specifications
TMP103BYFFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMP103BYFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMP103BYFFR: a temperature sensor in a four ball chip scale package
The TMP103BYFFR is a digital temperature sensor in a four ball wafer level package measuring 0.76 mm by 0.76 mm, with a two wire interface and a conversion engine that can be set to 8, 4, 1 or 0.25 Hz. At the default 0.25 Hz conversion rate it draws about 3 microamps, which is low enough to sit on a battery powered board without a switch.
The feature that separates it from other small sensors is multiple device access. The master can write a command that several devices act on at once, without addressing each one in turn. On a board with eight sensors around a chassis, that turns eight transactions into one, and it makes the readings comparable because they are taken in the same window.
Accuracy is plus or minus 1 C typical from minus 10 to 100 C. The device is a digital path with no calibration step at the end of the line, which is the reason to use it instead of a thermistor on a board that already has a processor and a bus.
Key data for the TMP103BYFFR
| Function | Digital temperature sensor with a two wire interface |
| Package | DSBGA, 4 balls, 0.76 mm by 0.76 mm |
| Resolution | 8 bit temperature result |
| Accuracy | Plus or minus 1 C typical from minus 10 to 100 C |
| Conversion rate | 8, 4, 1 or 0.25 Hz, 26 ms typical conversion time |
| Supply current | About 3 microamps at 0.25 Hz access |
| Supply range | 1.4 V to 3.6 V |
| Bus feature | Multiple device access commands reaching several devices at once |
| Addressing | Four selectable addresses, set at the package balls |
| Interface | Two wire, I2C and SMBus compatible |
| Temperature range | Minus 40 to 125 C operation |
| Ordering | TMP103BYFFR, large tape and reel |
Multiple device access, and the traffic it removes
A normal bus read is a start, an address, a register pointer, a restart, a read and a stop. Eight sensors means eight of those sequences, and each one is a chance for a bus error. A command that addresses several devices at once removes most of the traffic and makes the timing of the readings tight.
The cost is that all the devices must be configured to respond to the same group command, and the group is set at configuration time. A board that mixes sensors with different group settings will find that some of them ignore the broadcast, and the failure looks like a missing reading rather than a configuration error.
For a chassis with eight or sixteen points, this is the difference between a bus that is busy all the time and one that is quiet between measurements. On a small board with one sensor, it makes no difference at all.
Placing a part the size of a pin head
A 0.76 mm package with four balls needs a placement machine that can hold it, a stencil that can print for it and a reflow profile that does not tombstone it. On a board that also carries 0402 passives, the sensor is not the hardest part, but it is the one that fails silently if it is placed rotated.
The balls also carry the address setting, so the orientation decides which address the device answers on. A board that is assembled with one sensor rotated will still pass a functional test if only one sensor is read, and will fail in the field when two devices answer at once.
Thermally, the package has almost no mass, so it follows the copper under it rather than the air. A sensor placed on a thermal pad connected to a hot component will read that component, which is usually what is wanted. A sensor placed on a ground plane far from any heat source will read the board average and react slowly.
Where it fits in a build
Wearables, battery packs, small medical devices and any product where the board area is the constraint. The 1.4 V supply range also allows it to run from a single cell without a boost converter, which is unusual for a sensor with a bus interface.
Boards that carry several of these are usually kitted as a set, because a reel of 0.76 mm parts is not something a line wants to open for one placement. The kitting service page covers how the parts for one build are grouped, and the BOM scrubbing page covers how the bill of material is checked for address conflicts and duplicated positions before release.
The sourcing side of this part is covered on the one stop BOM sourcing. For a board with several sensors and their pull ups on one release, that page covers how the small parts are grouped and consolidated.
Questions we get on this code
Can it run from a coin cell? Yes, from 1.4 V to 3.6 V, and at 0.25 Hz conversion the average current is a few microamps. The bus pull ups then become the dominant load, so their value matters more than the sensor.
Does the 8 bit result limit the usefulness? It gives about 1 C steps, which matches the accuracy of the part. A product that needs 0.0625 C resolution needs a 12 bit sensor, and that is a different part in a bigger package.
How is the address set? By the ball connections on the package, which means by the board. Four addresses are available, so a bus with more than four of these needs a multiplexer or a second bus.
What happens if the bus is idle for a long time? The device keeps converting at the rate it was set to and the last result stays available. There is no sleep mode that has to be exited, which is convenient, but it also means the current is drawn continuously.