TLC6C5712QPWPRQ1
Product Specifications
TLC6C5712QPWPRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TLC6C5712QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TLC6C5712QPWPRQ1: twelve channel constant current LED sink with dot correction and diagnostics, in a 28 pin HTSSOP body
TLC6C5712QPWPRQ1 is a twelve channel current sink that sets its output current from one external resistor, trims each channel in 256 steps, and reports open and short faults over SPI in a HTSSOP body of 28 pins. The QPWP suffix is the 28 pin HTSSOP with the PowerPAD on the underside, AEC-Q100 grade 1 from minus 40 to 125 C, HBM class H3A and CDM class C4B. Output current is set by the resistor on IREF, 12.2 kohm giving 50 mA per channel and 8.13 kohm giving 75 mA, and the reference sits at 1.229 V typical. Each channel carries its own 8 bit dot correction, six PWM inputs handle dimming, and the part is specified at 3 percent channel to channel and device to device.
Order code and package
| Order code | TLC6C5712QPWPRQ1 |
| Function | 12 channel constant current sink, SPI control, dot correction |
| Package | HTSSOP, 28 pins, PowerPAD, body code PWP, tape and reel |
| Qualification | AEC-Q100 grade 1, HBM class H3A, CDM class C4B |
| Output current | up to 50 mA per channel with 12.2 kohm, 75 mA with 8.13 kohm |
| Output voltage | 7 V maximum on any output |
| Dropout | 0.75 V at 50 mA, 1.2 V at 75 mA |
| Current accuracy | 3 percent channel to channel, 3 percent device to device |
| Dot correction | 8 bit, 256 steps, per channel |
| Dimming | 6 PWM inputs with frequency supervision |
| Thermal resistance | 39 degrees per watt junction to ambient |
| Temperature range | minus 40 to 125 C, grade 1 |
| Datasheet | SLVSCO9A, revision of August 2015 |
Electrical parameters that decide the application
| Reference voltage | 1.229 V typical, 1.204 to 1.254 V at 20.5 kohm |
| Maximum output current | 50 mA at 0.75 V with 12.2 kohm, 75 mA at 1.2 V with 8.13 kohm |
| Minimum output current | 0.165 mA typical at 0.75 V with 12.2 kohm |
| Minimum output voltage | 0.5 V at 5 V, 0.75 V at 3.3 V, 1.2 V at 75 mA |
| Absolute current error | 3 percent at 50 mA and 30 mA, 7.5 percent at 10 mA |
| Dot correction DNL | plus or minus 0.6 mA at 50 mA full scale |
| Supply current | 3 mA typical at 5 V, 4.5 mA maximum |
| Power on reset | 2.7 V rising, 2.5 V falling, 0.2 V hysteresis |
| Default current | 10 mA typical when a reference fault is detected |
| PWM pull up | 150 kohm typical, 105 to 230 kohm |
| ERR output | open drain, 0.1 VCC drop at 4 mA |
| SDO output | 0.9 VCC high, 0.1 VCC low at 4 mA |
Points to check before this part goes on a BOM
The 7 V output ceiling changes what the part can drive. Three white LEDs in series need about 9.6 V at 50 mA, which is outside the rating, so the strings have to be two LEDs or the supply has to stay near 7 V. A cluster built around a 12 V rail and three LED strings needs a different device, and this is the first check on any substitution.
Dropout is specified at the current it is used at: 0.75 V at 50 mA, 1.2 V at 75 mA, and the minimum output voltage rises to 1.2 V for the 75 mA case. The headroom left for the LED string is the supply minus the LED forward voltage minus that dropout, and it has to be positive at the cold end of the temperature range where the forward voltage is highest.
Dot correction is a per channel multiplier, not a per channel current setting, and it is 8 bit. The DNL of plus or minus 0.6 mA at a 50 mA full scale means a one step change is not a fixed current step, so a brightness match done by sweeping all 256 codes costs more time than a two point calibration.
The reference resistor is the accuracy of the whole device. With 61 kohm the maximum output is 10 mA and the absolute error grows to 7.5 percent, five times the 1.5 percent at 30 mA, so a low current cluster pays in accuracy. The IREF pin also detects an open or shorted resistor and falls back to a 10 mA default, which keeps lamps lit but no longer matched.
Thermal resistance of 39 degrees per watt is a PowerPAD figure and only holds with the pad soldered to a copper area and stitched to an inner layer. Twelve channels at 50 mA and 0.75 V dropout is 450 mW, an 18 degree rise, which is comfortable, but twelve at 75 mA and 1.2 V is 1.08 W and 42 degrees, and at 85 C ambient that is a junction near 127 C.
Six PWM inputs with frequency supervision means the device itself complains if a dimming signal stops. The supervision is the reason a cluster does not simply freeze at a fixed brightness when the body controller halts, and it depends on the PWM pins being driven rather than tied high.
Where this order code fits
Automotive cluster tell tales, panel and button backlighting, bar graph indicators, shifter position displays and sequential turn signals all need consistent brightness across channels that sit at different temperatures. The fault reporting is the second reason it is chosen: open load, short to ground, shorted LED and adjacent pin shorts are all detected in both the on and the off state, which is what a lamp out warning needs. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Incoming Inspection Plan page.
Questions buyers ask
How is the output current set? By the resistor on IREF. The reference is 1.229 V typical, 12.2 kohm gives 50 mA per channel at a 0.75 V output and 8.13 kohm gives 75 mA at 1.2 V.
Can it drive three white LEDs in series? No. The outputs are rated 7 V, and three white LEDs need about 9.6 V plus dropout. Two LEDs in series per channel fit inside the rating on a 5 V or 6 V supply.
Is the brightness trim per channel? Yes, each channel has its own 8 bit dot correction register, and the part is specified at 3 percent channel to channel without trimming, so the trim is for matching LEDs rather than for correcting the device.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.