Contact Us

TLC339CD

Brand: Texas Instruments
Texas Instruments TLC339CD is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TLC339CD — Power Management & Signal Chain | Superb Automation

TLC339CD

Texas Instruments — Power Management & Signal Chain

Product Overview

The TLC339CD from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TLC339CD: quad micropower LinCMOS comparator with open drain outputs in a 14 pin SOIC body

TLC339CD is four independent CMOS comparators in one package that together draw 44 microamps and answer in 2.5 microseconds at 5 millivolts of overdrive in a SOIC body of 14 pins. The D suffix is the 14 pin SOIC and the C grade runs 0 to 70 C. The part is functionally the LM339 quad comparator but draws about one twentieth of the current: 44 microamps typical and 80 maximum for all four comparators at 5 V, which is 200 microwatts. Response time is 2.5 microseconds at 5 mV of overdrive, the outputs are open drain MOS with 8 to 20 mA of sink, and the input common mode reaches to VDD minus 1 V.

Order code and package

Order codeTLC339CD
Functionquad differential comparator, open drain output
PackageSOIC, 14 pins, body code D
Supply range3 to 16 V, 18 V absolute maximum
Supply current44 microamps typical, 80 maximum for four comparators
Response time2.5 microseconds typical at 5 mV overdrive
Output sink8 to 20 mA low level output current
Input offset voltage1.4 mV typical, 5 mV maximum at 25 C
Input bias current5 picoamps typical, 0.6 nanoamps at 70 C
Common mode range0 to VDD minus 1 V, VDD minus 1.5 V over temperature
Output typeopen drain MOS, wired OR capable
Temperature range0 to 70 C, C suffix
DatasheetSLCS119B, revision of December 2006

Electrical parameters that decide the application

Input offset voltage1.4 mV typical, 5 mV maximum at 25 C, 6.5 mV over 0 to 70 C
Input bias current5 picoamps typical at 25 C, 0.6 nanoamps at 70 C
Input offset current1 picoamp typical, 0.3 nanoamps at 70 C
Common mode rejection84 dB typical
Supply rejection85 dB typical from 5 to 10 V
Low output level300 mV typical, 400 maximum at 6 mA, 650 at 70 C
High level leakage0.8 nanoamps typical at 5 V, 1 microamp at 70 C
Supply current over temperature100 microamps maximum from 0 to 70 C
Offset drift0.23 microvolts per month including the first 30 days
Input resistance10 to the twelfth ohm typical
Output current rating20 mA absolute maximum per output
Response time overdrivespecified at 5 mV, stretched at lower overdrive

Points to check before this part goes on a BOM

The 2.5 microsecond response is quoted at 5 mV of overdrive, and the offset limit is also 5 mV. A signal that only just crosses the threshold therefore sees no overdrive at all in the worst case unit, and the delay grows by an order of magnitude. A threshold detector on this part needs 20 to 50 mV of overdrive to keep the timing it was specified for.

Supply current is 44 microamps typical and 80 maximum at 25 C, but 100 microamps maximum over the full range. The 100 to 1 range against a bipolar LM339 is the whole reason to pay for the CMOS part, and it is also why the input bias current of 5 picoamps becomes 600 picoamps at 70 C: leakage doubles about every ten degrees.

The input common mode stops 1 V below the positive rail at 25 C and 1.5 V below over temperature. On a 5 V rail that means the usable window tops out at 3.5 V, so a 5 V referenced threshold has to come from a divider rather than from the rail, and the divider tolerance enters the threshold error.

The output is open drain with 8 to 20 mA of sink and 400 mV at 6 mA. That is enough to drive an optocoupler or a logic input with a pull-up, but not enough to drive a relay, and the 20 mA absolute maximum means two outputs wired together at 15 mA each are already at the limit of one output pin.

Offset is 1.4 mV typical but 5 mV maximum, a factor of 3.5, and the 6.5 mV over temperature adds to it. A window comparator built with two sections of the same package has both offsets working in the same direction on process, so the window can shift by up to 13 mV as a unit rather than staying centred.

Four comparators in one 14 pin body share a single ground pin, and all four outputs sink into it. At 6 mA on each of four outputs the ground pin carries 24 mA, and the internal bond wire and lead resistance adds a common offset that appears as threshold shift on the other channels. Splitting the load across two packages is the usual fix.

Where this order code fits

Window comparators, level detectors and wired OR fault buses in battery powered equipment: a four cell lithium pack monitoring four thresholds, a window detector on a 24 V rail through a divider, a zero crossing detector bank, or a set of four thermistors sharing one wired OR alarm line. The open drain output is what allows several of them to share one interrupt pin without a logic gate. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

How much overdrive does the 2.5 microsecond response need? 5 mV, which is the same as the maximum offset on this part. For predictable timing, present 20 to 50 mV of overdrive so the offset cannot eat the whole step.

Can the four outputs be wired together? Yes, that is what open drain gives, and the wired OR works without extra parts. Each output still sinks its own current, so four outputs into one pull-up must stay inside the 20 mA per output rating.

What is the current at 70 C? 100 microamps maximum for all four comparators, against 80 microamps at 25 C. The bias current moves much further, from 5 picoamps to 600 picoamps.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.