Contact Us

TLC27M2CDR

Brand: Texas Instruments
Texas Instruments TLC27M2CDR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TLC27M2CDR — Power Management & Signal Chain | Superb Automation

TLC27M2CDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TLC27M2CDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TLC27M2CDR: dual LinCMOS operational amplifier with a 525 kHz bandwidth at 2.1 milliwatts, on tape and reel

TLC27M2CDR is a dual CMOS operational amplifier that trades the micropower of the L version for a 525 kHz bandwidth while still drawing under half a milliamp per amplifier in a SOIC body of 8 pins. The C suffix fixes 0 to 70 C and the DR suffix is the 8 pin SOIC on tape and reel. Each amplifier draws 210 microamps typical and 560 maximum at 5 V, which is 2.1 mW for the pair, and the unity gain bandwidth is 525 kHz with a 0.43 V per microsecond slew rate. Input noise is 32 nanovolts per root hertz at 1 kHz and the input common mode reaches below the negative rail on this grade.

Order code and package

Order codeTLC27M2CDR
Functiondual operational amplifier, LinCMOS, single supply
PackageSOIC, 8 pins, body code D, tape and reel
Supply range3 to 16 V, 18 V absolute maximum
Supply current210 microamps typical, 560 maximum per amplifier at 5 V
Unity gain bandwidth525 kHz typical, 400 minimum at 70 C
Slew rate0.43 V per microsecond typical, 0.36 at 70 C
Power dissipation2.1 mW for the pair at 5 V
Input offset voltage10 mV maximum at 25 C, 12 mV over the range
Input resistance10 to the twelfth ohm typical
Temperature range0 to 70 C, C suffix
Long term stability0.1 microvolt per month including the first 30 days
DatasheetSLOS051E, revision of August 2008

Electrical parameters that decide the application

Input offset voltage10 mV maximum at 25 C, 12 mV over 0 to 70 C on this grade
Offset drift1.7 microvolts per degree average from 25 to 70 C
Input bias current0.6 picoamps typical, 60 maximum at 25 C, 600 at 70 C
Input offset current0.1 picoamps typical, 60 maximum at 25 C, 300 at 70 C
Common mode rangeminus 0.2 to 4 V typical on a 5 V rail
High output level3.2 V minimum into 1 megohm
Low output level150 mV at no load
Large signal gain50 V per mV minimum
Common mode rejection60 dB minimum, 92 typical
Supply rejection70 dB minimum, 93 to 94 typical
Phase margin40 degrees at unity gain into 20 pF
Full power bandwidth60 kHz at 10 V peak to peak into 100 kohm

Points to check before this part goes on a BOM

The bandwidth figure has a temperature and load condition attached. 525 kHz is typical at 25 C into a 20 pF load, the guaranteed figure at 70 C is 400 kHz, and the phase margin is only 40 degrees, so a 100 pF cable at the output will oscillate. A 100 ohm series resistor at the output pin is not optional on a board with a connector.

The 2.1 mW headline is for the pair at 5 V and matches 210 microamps per amplifier, but the maximum column is 560 microamps per amplifier, which is 5.6 mW for the pair. A budget that uses the typical figure is out by a factor of 2.7, and that factor is what decides whether a coin cell lasts five years or two.

Offset is 10 mV in the plain TLC27M2 grade. The same datasheet offers the TLC27M2A at 0.95 mV typical and 6.5 mV maximum over the range and the TLC27M2B at 2 mV maximum at 25 C, so a precision requirement belongs on a different order code, and a board that needs the grade cannot be fixed by trimming because the drift term is in the part.

The input common mode extends 0.2 V below the negative rail, which is what makes a single supply ground sensing front end possible. The top of the range is 4 V typical on a 5 V rail, so a signal referenced to the positive rail, such as a high side current sense, is outside the window and needs a divider or a different amplifier.

Noise of 32 nanovolts per root hertz at 1 kHz is 3.2 microvolts over a 10 kHz band and 10 microvolts over 100 kHz. Against a 10 mV offset the noise is small, but against a 100 microvolt thermocouple signal over a 100 kHz band it is a tenth of the signal, so the bandwidth has to be limited at the amplifier rather than at the converter.

The output can reach the negative rail but the sink current is modest. The low level is 150 mV at no load, and the 30 mA absolute maximum is a survival rating: a 2 kohm load to ground is the sensible limit for this part, and a heavier load shifts the low level up and costs open loop gain.

Where this order code fits

Sensors and control loops that need more than the 50 kHz of the micropower version but cannot afford a bipolar amplifier: thermocouple and RTD front ends, active filters in the audio band, strain gauge bridges, and the error amplifier of a low dropout regulator built from discrete parts. Portable instruments use it where a 10 microamp part would be too slow and a 3 mA part would flatten the cell. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

How fast is it compared with the TLC27L2? About ten times. The M version has a 525 kHz unity gain bandwidth and a 0.43 V per microsecond slew rate against 0.05 MHz and less than 0.05 V per microsecond on the micropower L version, at the cost of 210 microamps per amplifier instead of 10.

Is the offset grade selectable? Yes, through the order code. The plain TLC27M2 is 10 mV, the A suffix is 0.95 mV typical and 6.5 mV maximum, and the B suffix is 2 mV maximum at 25 C.

Can it drive a capacitive load? Only with a series resistor. Phase margin is 40 degrees into 20 pF, so a cable or a large gate capacitance needs 100 ohm at the output pin to keep the loop stable.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.