Contact Us

TL7705ACDR

Brand: Texas Instruments
Texas Instruments TL7705ACDR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL7705ACDR — Power Management & Signal Chain | Superb Automation

TL7705ACDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL7705ACDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL7705ACDR: 5 V supply voltage supervisor with an externally set reset delay in an 8 pin SOIC body

TL7705ACDR is a reset controller that watches a 5 V rail through a 4.55 V sense comparator and holds a processor in reset until the rail has been good for a capacitor set time in a SOIC body of 8 pins. The D suffix is the 8 pin SOIC, R adds tape and reel, and the C grade covers 0 to 70 C. The sense threshold is 4.54 to 4.6 V at 25 C with 15 mV of hysteresis, both RESET and RESET outputs are brought out at 16 mA, and the delay is set by CT: 0.1 microfarad gives 0.65 to 2.6 ms with 1.3 ms typical. A 2.53 V reference is available on the REF pin and the device runs from 3.5 V to 18 V.

Order code and package

Order codeTL7705ACDR
Functionsupply voltage supervisor, 5 V sense, both reset polarities
PackageSOIC, 8 pins, body code D, tape and reel
Supply range3.5 to 18 V, 20 V absolute maximum
Sense threshold4.54 V minimum, 4.55 typical, 4.6 maximum at 25 C
Sense hysteresis15 mV
Reset delay1.3 ms typical with CT of 0.1 microfarad
Output drive16 mA source and sink on both reset outputs
Reference output2.53 V typical, 2.48 to 2.58 V
Supply current1.8 mA typical, 3 mA maximum
Thermal resistance97 degrees per watt, D body
Temperature range0 to 70 C, C suffix
DatasheetSLVS028K, revision of September 2016

Electrical parameters that decide the application

Negative going threshold4.55 V typical, 4.54 to 4.6 V window at 25 C
Delay lawtd equals 1.3 times ten to the four multiplied by CT
Output pulse duration0.65 to 2.6 ms with CT of 0.1 microfarad
Propagation delay1 microsecond from RESIN to RESET
Sense to output delay2 microseconds at 200 mV beyond the threshold
Rise time, RESET3.5 microseconds into 4.7 kohm
Fall time, RESET0.2 microseconds into 4.7 kohm
High output levelVCC minus 1.5 V at 16 mA
Low output level0.4 V at 16 mA
Reference voltage2.53 V typical, 2.48 to 2.58 V at 25 C
RESIN input0.6 V low, 2 V high, 20 microamps at 2.4 V
Supply current1.8 mA typical, 3 mA maximum

Points to check before this part goes on a BOM

The 4.55 V threshold sits 9 percent below nominal. A 5 V rail at minus 5 percent is 4.75 V, which is 150 mV above the window top, so the supervisor stays inactive on a legal rail. At minus 10 percent the rail is 4.5 V, 40 mV below the window bottom, so it trips. Between 4.6 and 4.75 V no decision is guaranteed, and that band is where the processor is already outside its own supply limit.

Hysteresis of 15 mV is small against the ripple on a loaded 5 V rail. A 100 mV ripple crossing the threshold asks the comparator to toggle at the ripple rate, and the CT delay only slows the response after the first crossing, so the bulk capacitor and the decoupling are part of the reset function rather than an optional extra.

The delay is linear in CT by the published law td equals 1.3 times ten to the fourth times CT, but the spread at 0.1 microfarad is 0.65 to 2.6 ms, a factor of four. A specification written as a minimum reset time therefore has to be set from the fast end of that window and checked at the slow end for a stuck reset.

SENSE is the monitored rail on this member of the family, and the recommended input range tops out at 10 V on this order code while the absolute maximum is 20 V. Putting 12 V on a TL7705A leaves the recommended range and the device is then outside every table in the datasheet; the 12 V member is the TL7712A at 10.8 V.

Both outputs are rated 16 mA and the rise time of 3.5 microseconds is quoted into 4.7 kohm. A 100 kohm pull-up multiplies that edge by roughly twenty, and a slow edge on a processor reset pin can be read as a second reset by the internal synchroniser, which is a common cause of a board that boots twice.

RESIN draws 20 microamps at 2.4 V and minus 100 microamps at 0.4 V, so a mechanical switch or a watchdog output can drive it directly. The pin has no idle state of its own, and leaving it open is not a defined condition, which is how a board ends up latching in reset with no fault in the supply.

Where this order code fits

It is the reset controller on 5 V processor boards: meters, appliance controls, telecom line cards and instruments where the processor has to stay off until the rail and the clock are stable. The same part supervises a 5 V backplane in a card cage, and the REF output gives a second rail a comparison node through an external divider. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Does it trip on a 5 V rail at minus 5 percent? No. The window tops out at 4.6 V and a minus 5 percent rail is 4.75 V, so the part stays inactive and the processor runs. It trips at about 4.5 V, which is minus 10 percent.

How do I get a 50 ms reset delay? CT scales linearly at 1.3 times ten to the fourth times CT, so about 3.9 microfarad gives 50 ms nominal. Because the spread at a given capacitor is a factor of four, the minimum time has to be taken from the fast end of that spread.

Can the same part supervise a 12 V rail? No. SENSE is rated to 10 V recommended and 20 V absolute on this order code. The 12 V member of the family is the TL7712A, whose threshold is 10.8 V.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.