Contact Us

TL3472IDR

Brand: Texas Instruments
Texas Instruments TL3472IDR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL3472IDR — Power Management & Signal Chain | Superb Automation

TL3472IDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL3472IDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL3472IDR: dual high slew rate operational amplifier specified from minus 40 to 105 C, on tape and reel

TL3472IDR is the industrial temperature version of the same dual amplifier, with the same 4.5 MHz bandwidth carried across a 145 degree span in a SOIC body of 8 pins. The I suffix on this order code is not the usual minus 40 to 85 C industrial range, it is minus 40 to 105 C, which is 20 degrees more than most of the analogue catalogue beside it. The DR packing is the 8 pin SOIC on tape and reel. Gain bandwidth, slew rate and settling are the same as the commercial part, and the full range offset limit over that 145 degree span is 12 mV.

Order code and package

Order codeTL3472IDR
Functiondual operational amplifier, single or split supply
PackageSOIC, 8 pins, body code D, tape and reel
Supply range4 to 36 V total, plus or minus 18 V absolute maximum
Gain bandwidth4.5 MHz at 100 kHz
Slew rate8 V per microsecond rising, 13 V per microsecond falling
Settling2 microseconds to 0.1 percent on a 10 V step
Supply current0.56 mA typical, 5.5 mA maximum per channel over temperature
Thermal resistance130.7 degrees per watt, D body
Temperature rangeminus 40 to 105 C, I suffix
Junction limit150 C virtual junction
DatasheetSLOS200H, revision of December 2025

Electrical parameters that decide the application

Input offset voltage1.5 mV typical, 10 mV maximum at 25 C, 12 mV over the full range
Offset drift10 microvolts per degree, so 1.45 mV across 145 degrees
Input bias current0.015 nanoamps typical, 500 nanoamps maximum at 25 C, 700 over temperature
Input offset current0.0175 nanoamps typical, 300 nanoamps maximum
Common mode rangeminus 15 to plus 12.8 V on plus and minus 15 V, 0 to 2.8 V on a 5 V rail
Large signal gain25 V per mV minimum, 100 typical
Common mode rejection65 dB minimum, 97 dB typical
Supply rejection70 dB minimum, 97 dB typical
Supply current4.5 mA typical and 5.5 mA maximum per channel at 25 C
Power bandwidth85 kHz at 20 V peak to peak into 2 kohm
Output short circuit75 mA at 25 C, derated by the dissipation rating
Junction temperature150 C absolute maximum, 260 C lead for 10 seconds

Points to check before this part goes on a BOM

The 105 C ambient is the reason to buy this order code, but the junction limit is 150 C. At 130.7 degrees per watt in the D body, a 45 degree rise is the whole budget, which is 344 mW at the top of the range. A dual drawing 5.5 mA per channel at 36 V already uses 396 mW before any load, so the supply voltage and the ambient trade against each other.

Offset drift is 10 microvolts per degree, and over the 145 degree span the drift term is 1.45 mV. That is small next to the 12 mV limit, which means the 25 C offset is what dominates the error and a board trimmed at room temperature keeps most of its accuracy at 105 C.

Leakage current is specified at 25 C and again over the full range, 500 and 700 nanoamps. On a 100 kohm source the difference between those two numbers is 20 mV of drift that no offset trim can remove, so high impedance networks belong with a low bias part rather than this one.

The input common mode stops 2.2 V below the positive rail on a 5 V supply and 2.2 V below on plus and minus 15 V. A regulator error amplifier that senses its own output at the rail therefore needs a divider, and the divider sets the gain error through its own tolerance.

Ordering by suffix alone is risky on this family because the I grade here means 105 C, not the 85 C that the same letter means on the TL3116 or the TLC27L2. Two boards in the same product can carry the same letter and different temperature limits, so the temperature has to be read from the datasheet of the part number, not from the letter.

The tape and reel packing is the DR suffix and the reel quantity follows the standard for the 8 pin SOIC. The D packing without R is the tube, and mixing the two in one assembly line is the usual cause of a line stop rather than a technical fault.

Where this order code fits

Cabinet mounted equipment that sees the inside of an enclosure rather than the room: motor drives, industrial power supplies, battery chargers and outdoor telecom units where the ambient at the board reaches 85 to 95 C and the part has to keep its offset and its gain. It is also the sensible order code for a board that is qualified once and sold into both commercial and industrial versions. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Is the I grade a standard industrial part? Not on this device. TI specifies the TL3472I from minus 40 to 105 C, while the same letter on the TL3116 and the TLC27L2 means minus 40 to 85 C, so the letter alone does not fix the range.

Does the higher temperature change the electrical limits? The 25 C limits are identical to the C grade and the full range offset limit is 12 mV, but the supply current limit rises from 4.5 to 5.5 mA per channel and the short circuit rating only holds at 25 C.

What is the difference between the DR and D order codes? Packing only. Both are the 8 pin SOIC with the same die and the same temperature range, one on tape and reel and one in tubes.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.