Contact Us

TL3472CDR

Brand: Texas Instruments
Texas Instruments TL3472CDR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL3472CDR — Power Management & Signal Chain | Superb Automation

TL3472CDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL3472CDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL3472CDR: dual high slew rate operational amplifier on a 4.5 MHz gain bandwidth, supplied on tape and reel

TL3472CDR is a dual bipolar operational amplifier that runs from 4 V to 36 V on one rail and takes its input common mode down to the negative rail in a SOIC body of 8 pins. The DR suffix is the 8 pin SOIC in tape and reel, and the C grade is specified from 0 to 70 C. Gain bandwidth is 4.5 MHz, the positive slew rate is 8 V per microsecond and the negative slew rate 13 V per microsecond, and a 10 V step settles to 0.1 percent in 2 microseconds. Supply current is 0.56 mA typical and 4.5 mA maximum per channel, and the output sources or sinks 75 mA into a short at 25 C.

Order code and package

Order codeTL3472CDR
Functiondual operational amplifier, single or split supply
PackageSOIC, 8 pins, body code D, tape and reel
Supply range4 to 36 V total, plus or minus 18 V absolute maximum
Gain bandwidth4.5 MHz at 100 kHz
Slew rate8 V per microsecond rising, 13 V per microsecond falling
Settling2 microseconds to 0.1 percent on a 10 V step
Output current75 mA source or sink, short circuit protected
Supply current0.56 mA typical, 4.5 mA maximum per channel
Thermal resistance130.7 degrees per watt, D body
Temperature range0 to 70 C, C suffix
AlternativesMC33072 and MC34072 replacement
DatasheetSLOS200H, revision of December 2025

Electrical parameters that decide the application

Input offset voltage1.5 mV typical, 10 mV maximum on 5 V, 12 mV over the full range
Offset drift10 microvolts per degree
Input bias current0.015 nanoamps typical, 500 nanoamps maximum, 700 over temperature
Input offset current0.0175 nanoamps typical, 300 nanoamps maximum
Common mode rangeminus 15 to plus 12.8 V on plus and minus 15 V, 0 to 2.8 V on a 5 V rail
Large signal gain25 V per mV minimum, 100 typical
Common mode rejection65 dB minimum, 97 dB typical
Supply rejection70 dB minimum, 97 dB typical
Input noise10.8 nanovolts per root hertz at 1 kHz
Power bandwidth85 kHz at 20 V peak to peak into 2 kohm
Channel separation101 dB at 10 kHz
Phase margin70 degrees unloaded, 50 degrees into 300 pF

Points to check before this part goes on a BOM

The offset table has two columns and both matter. On a 5 V rail the offset is 1.5 mV typical and 10 mV maximum, on plus and minus 15 V it is 1.0 mV typical and 10 mV maximum, and the full range limit is 12 mV. A budget written around the typical figure is out by a factor of six against the guaranteed one.

Bias current is 500 nanoamps maximum at 25 C and 700 nanoamps over temperature, and the differential input resistance is 540 Gohm. That combination means the resistive divider in front of the amplifier, not the amplifier input, sets the error: a 100 kohm source carries 50 mV of offset from bias current alone.

The part is unity gain stable, with 70 degrees of phase margin unloaded and 50 degrees into a 300 pF load. That 20 degree loss is the reason a cable or a capacitive sensor needs a series resistor at the output, especially on a 5 V rail where the output stage is working at low quiescent current.

Slew rate is not symmetrical: 8 V per microsecond rising against 13 V per microsecond falling. A square wave clock or a charge pump drive comes out with a 60 percent difference between edges, and on a 20 V peak to peak output the full power bandwidth is 85 kHz, not the 4.5 MHz the small signal curve suggests.

Supply current is quoted per channel, so a dual at 36 V can draw 9 mA and dissipate 324 mW. With 130.7 degrees per watt that is a 42 degree rise in still air before any load current, and the output stage adds its own share when driving 600 ohm or lower.

The output can be shorted to either rail indefinitely at 25 C, but the note in the table ties that to the dissipation rating, so a short at 70 C ambient is not covered. A 75 mA short at 12 V is 0.9 W in the package, twice what the D body can take at that ambient.

Where this order code fits

Single supply signal conditioning on 5 V and 12 V rails is the natural home: transducer buffers, active filters, comparators built from an amplifier, and error amplifiers in linear regulators. On split rails the same 8 pinout replaces MC33072 and MC34072 boards without a board change, and the ground sensing input removes the need for a negative supply on single rail boards. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Power Management Cross Reference page.

Questions buyers ask

Is 4.5 MHz the gain at which the part is usable? It is the unity gain crossover. At a closed loop gain of 10 the small signal bandwidth is about 450 kHz, and the slew rate limits a 20 V peak to peak output to 85 kHz whatever the gain.

What separates the C grade from the I grade? Temperature only. The C grade covers 0 to 70 C, the I grade covers minus 40 to 105 C, and both share the 10 mV offset at 25 C and the 12 mV full range limit.

Will it run from a 3.3 V rail? No. The recommended supply starts at 4 V, and the input common mode range on a 5 V rail already stops at 2.8 V, so a 3.3 V rail leaves almost no headroom on either side.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.