Contact Us

TL1963A-18DCQR

Brand: Texas Instruments
Texas Instruments TL1963A-18DCQR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL1963A-18DCQR — Power Management & Signal Chain | Superb Automation

TL1963A-18DCQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL1963A-18DCQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL1963A-18DCQR: 1.5 amp low dropout regulator with a fixed 1.8 V output in a SOT-223 body

TL1963A-18DCQR is a fast transient low dropout linear regulator that holds 1.8 V at 1.5 amps with 340 millivolts of dropout and 40 microvolts RMS of output noise in a SOT-223 body of 6 pins. The DCQ suffix is the SOT-223 body and the -18 is the fixed 1.8 V option, which the data sheet specifies at 1.773 to 1.827 V over the full temperature range at 1 milliamp, a plus or minus 1.5 percent window. Dropout is 340 millivolts typical at 1.5 amps, output noise is 40 microvolts RMS over 10 Hz to 100 kHz, quiescent current is 1 milliamp, and the part needs 1 microfarad at the input and 10 microfarads at the output to be stable.

Order code and package

Order codeTL1963A-18DCQR
Function1.5 A low dropout linear regulator, fixed 1.8 V
PackageSOT-223, 6 pins, body code DCQ
Output voltage1.773 to 1.827 V over temperature, 1.8 V nominal
Output current1.5 A
Dropout340 mV typical at 1.5 A
Quiescent current1 mA
Output noise40 microvolts RMS from 10 Hz to 100 kHz
Input capacitor1 microfarad minimum
Output capacitor10 microfarad minimum
Protectionreverse battery and reverse output current
Temperature rangeminus 40 to plus 125 C junction

Electrical parameters that decide the application

Line regulation1.5 to 5 mV for the adjustable version, 2.5 to 7 mV for the fixed 1.8 V
Load regulation2 to 8 mV at 25 C, up to 20 mV over temperature
Reference voltage1.21 V for the adjustable version, 1.192 to 1.228 V
Minimum input2.8 V for the 1.8 V fixed option
Maximum input20 V
Output accuracyplus or minus 1.5 percent over temperature
Dropout at 1.5 A340 mV typical, 500 mV maximum
Reverse current protectionoutput can be driven above input without damage
Adjustable optionsame die with a 1.21 V reference pin
Thermal pathSOT-223 tab soldered to copper
Noise bypassexternal capacitor on the reference for lower noise
DatasheetSLVS719H, revision of June 2026

Points to check before this part goes on a BOM

The dropout figure is typical and the maximum is 500 millivolts, so a 1.8 V output needs at least 2.3 V at the input on a worst case unit, not 2.14 V. The data sheet's 2.8 V minimum input is the voltage at which the part is specified, which is half a volt above the worst case dropout floor and leaves room for input ripple.

Dissipation is the whole question with a linear regulator at 1.5 amps. From 2.8 V to 1.8 V the part dissipates 1.5 W, which in a SOT-223 with the tab soldered to a copper plane gives a junction rise of roughly 60 to 80 degrees. From 5 V to 1.8 V the same current dissipates 4.8 W, which no SOT-223 can pass, so the input rail as much as the current rating decides whether this part is usable.

The 40 microvolt RMS noise figure is for a 10 microfarad output capacitor and no bypass on the reference. Adding a bypass capacitor at the reference pin reduces the low frequency noise, which is where most of the 40 microvolts sits, but it also slows the startup and changes the loop response.

Stability depends on the output capacitor, and the data sheet requires 10 microfarads minimum with an ESR inside a specified window. A ceramic capacitor of 10 microfarads is at the low end of the permitted ESR range at room temperature and falls further in the cold, so a 22 microfarad ceramic is the safer choice and the data sheet's stability curves should be checked rather than assumed.

Load regulation of 20 mV maximum over temperature on a 1.8 V rail is 1.1 percent, which is larger than the 1.5 percent initial accuracy and the same order as the total error budget. A 1.8 V core rail with a plus or minus 5 percent requirement spends most of that budget in the regulator alone, before the input rail tolerance is counted.

Reverse output current protection matters in systems with several rails. If the 1.8 V rail comes up after the 3.3 V rail that it feeds, the output can be pulled above the input, and a regulator without this protection will conduct through its pass device and its body diode. The data sheet states the protection explicitly for this family, which is one reason it appears in multi rail boards.

Where this order code fits

Post regulation of a switching supply, FPGA and DSP core rails, and any 1.8 V rail that follows a noisy preregulator use this part. Its reverse battery and reverse current protection also make it usable in battery systems where the output can be back driven during a fault. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

What input voltage does the 1.8 V version need? 2.8 V minimum for full specification at 1.5 amps. With a 500 millivolt maximum dropout the electrical minimum is 2.3 V, but the part is not specified below 2.8 V, and input ripple has to stay above it.

How much heat does it produce at 1.5 amps? From 2.8 V to 1.8 V, 1.5 W. From 3.3 V to 1.8 V, 2.25 W. From 5 V to 1.8 V, 4.8 W, which is beyond what a SOT-223 can pass with the tab on a copper plane.

Is a 10 microfarad ceramic output capacitor enough? It is the minimum. The stability window includes an ESR range, and a ceramic capacitor at the minimum value has the least margin in the cold, so 22 microfarads is the usual production choice.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.