Contact Us

THS6092ID

Brand: Texas Instruments
Texas Instruments THS6092ID is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

THS6092ID — Power Management & Signal Chain | Superb Automation

THS6092ID

Texas Instruments — Power Management & Signal Chain

Product Overview

The THS6092ID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

THS6092ID: dual xDSL line driver running from a single 12 V supply into a 25 ohm load

THS6092ID is a single supply version of the line driver family, specified from 5 V to 12 V with the output biased at mid rail so a transformer can be driven without a negative rail in a SOIC body of 8 pins. The part is specified with VCC+ at 12 V and VCC- at ground, a 750 ohm feedback resistor and a 25 ohm load, which puts the output quiescent point at half the rail. Bandwidth is 100 MHz at 12 V and 90 MHz at 5 V, slew rate is 600 V per microsecond at 12 V and 400 V per microsecond at 5 V, and the input common mode window is 1.5 to 3.5 V at 12 V and 1.1 to 3.9 V at 5 V, so the input sits inside a narrow band around mid rail.

Order code and package

Order codeTHS6092ID
Functiondual differential line driver, single supply
PackageSOIC, 8 pins, body code D
Supply rangesingle supply, specified at 12 V and at 5 V
Output current325 mA short circuit
Bandwidth100 MHz at 12 V, 90 MHz at 5 V
Slew rate600 volts per microsecond at 12 V, 400 at 5 V
Output swing1.9 to 10.1 V at 12 V, 1.4 to 10.6 V over temperature
Input common mode1.5 to 3.5 V at 12 V, 1.1 to 3.9 V at 5 V
Bias pointoutputs sit at mid rail for transformer coupling
Junction rangeminus 40 to plus 85 C, I suffix
DatasheetSLOS313, single supply xDSL driver family

Electrical parameters that decide the application

Differential offset1 mV typical, 6 mV maximum
Single ended offset6 mV typical, 16 mV maximum, 21 mV over temperature
Offset drift20 microvolts per degree
Bias current3 microamps typical, 10 microamps maximum
Voltage noise2.1 nanovolts per root hertz at 10 kHz
Third order distortionminus 70 dBc at 2 V peak to peak, minus 68 dBc at 7 V peak to peak
Crosstalkminus 65 dBc at 1 MHz on 5 V
Output current325 mA short circuit
Full power bandwidthabout 13 MHz at 7 V peak to peak on 12 V rails
Logic referenceshutdown pin referenced to the mid rail on the 6093
Package8 pin SOIC, no exposed pad
Datasheet note5 V and 12 V columns are separate specifications

Points to check before this part goes on a BOM

Output swing of 1.9 to 10.1 V on a 12 V rail is 8.2 V peak to peak, which is 29 V peak to peak differentially. The part cannot reach either rail, and the 1.9 V floor is higher than a typical rail to rail amplifier, because the output stage is biased for linearity rather than for headroom.

The 5 V column is not a scaled 12 V column. Slew rate drops from 600 to 400 V per microsecond and the input common mode window changes from 1.5 to 3.5 V to 1.1 to 3.9 V, so the bias network that sets the input at mid rail has to be rechecked when the same board is built with a 5 V rail.

Offset on a single supply is a differential problem. The 16 mV maximum refers to one output against mid rail, while the 6 mV maximum is the difference between the two outputs, and only the differential part survives the transformer. A 6 mV differential offset on a 1 V signal is 0.6 percent, which is inside a 12 bit converter but visible on a 16 bit one.

Distortion rises with amplitude in the wrong direction for a line driver. Minus 70 dBc at 2 V peak to peak becomes minus 68 dBc at 7 V peak to peak, and 7 V peak to peak on a 12 V supply is already close to the 8.2 V the output can reach, so the last volt of swing costs 2 dB of linearity.

Bias current of 10 microamps maximum through the 750 ohm feedback network is 7.5 mV of output offset, which on a 12 V single supply shifts the quiescent point away from mid rail. That shift reduces the available swing in one direction and is the reason the output window is quoted as a range rather than a symmetric figure.

The package is a plain 8 pin SOIC without an exposed pad, so the thermal path is the lead frame. At 325 mA of short circuit current and 12 V rails, a sustained fault dissipates more than the body can pass, which is why the fault current is specified as a short circuit condition and not as a continuous rating.

Where this order code fits

Customer premises ADSL modems and USB or PCI based DSL adapters use this part because they have a single 12 V or 5 V rail and no negative supply. It also fits single supply piezo drivers and any transformer coupled output that can be biased at half rail. Boards comparing it with a neighbouring part start from our How to Verify a Drop in Replacement page, and boards replacing a part that has gone end of life start from the Amplifier Cross Reference page.

Questions buyers ask

Can this part run from 5 V and still drive a full ADSL loop? It can run from 5 V, but the swing, slew rate and input window all change. On 5 V the output window is roughly 1.4 to 3.9 V, about 5 V peak to peak differential, which is not enough for a long loop.

Why is the input common mode window so narrow at 12 V? Because the input stage is referenced to mid rail and the part is a current feedback amplifier with a limited input stage range. On 12 V rails the usable input window is 1.5 to 3.5 V, so the feedback network has to keep both inputs inside that band.

What replaces this part if it is not available? The THS6093 is the same amplifier with a shutdown pin, and the THS6042 or 6043 are the split supply equivalents. None of them are pin identical, because the single supply parts bias the output at mid rail.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.