Contact Us

THS6022IPWP

Brand: Texas Instruments
Texas Instruments THS6022IPWP is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

THS6022IPWP — Power Management & Signal Chain | Superb Automation

THS6022IPWP

Texas Instruments — Power Management & Signal Chain

Product Overview

The THS6022IPWP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

THS6022IPWP: dual 250 mA differential line driver in a 20 pin PowerPAD HTSSOP body

THS6022IPWP is a dual current feedback line driver built for xDSL loops, with 200 mA of guaranteed output current into 50 ohms and separate supply pins for each half in a HTSSOP body of 20 pins. The PWP suffix is the thermally enhanced HTSSOP with the PowerPAD on the underside, and the data sheet gives 3.3 W of continuous dissipation at 25 C for the package, which is the number that decides whether a 250 mA drive is thermally possible in a closed modem enclosure. Each driver has its own VCC+ and VCC- pins, so the two halves can be decoupled independently, and the differential input limit is 6 V while the absolute maximum output current is 400 mA.

Order code and package

Order codeTHS6022IPWP
Functiondual differential line driver, current feedback
PackageHTSSOP, 20 pins, PowerPAD, body code PWP
Supply rangeplus or minus 5 V to plus or minus 15 V, 33 V total maximum
Output current200 mA minimum into 50 ohms, 400 mA absolute maximum
Bandwidth210 MHz at 50 ohms, 300 MHz at 100 ohms
Slew rate1900 volts per microsecond at a gain of 5
Settling70 nanoseconds to 0.1 percent on a 0 to 10 V step
Continuous dissipation3.3 W at 25 C for the package
Differential input limit6 V
Junction rangeminus 40 to plus 85 C, I suffix
DatasheetSLOS225D, revision of July 2007

Electrical parameters that decide the application

Offset voltage1 mV typical, 5 mV maximum at 25 C
Differential offset0.5 mV typical, 4 mV maximum
Offset drift20 microvolts per degree, differential 10 microvolts per degree
Bias current1 microamp typical, 5 to 10 microamps maximum, 12 microamps over temperature
Voltage noise1.7 nanovolts per root hertz at 10 kHz
Inverting input current noise16 picoamps per root hertz at 10 kHz
Common-mode rejection62 dB minimum, 73 dB typical
Input common modeplus or minus 13.3 V typical at a 15 V supply
Third order distortionminus 69 dBc at 500 kHz into 50 ohms with 20 V peak to peak
Crosstalkminus 64 dB at 1 MHz
Full power bandwidth30 MHz with 20 V peak to peak, 75 MHz with 4 V peak to peak
Open-loop transresistance4 megohms

Points to check before this part goes on a BOM

The 250 mA in the title is a typical capability, not the guaranteed line. The electrical table promises 200 mA minimum into 50 ohms, and the absolute maximum output current is 400 mA, so a board that needs 240 mA on every unit is outside the guaranteed column and has to be qualified against the current limit instead of the headline.

Dissipation, not current, is what limits this package. Driving 20 V peak to peak into 50 ohms means 200 mA of peak current and about 2 W of average dissipation per amplifier at the crest factor of a multicarrier signal, which is most of the 3.3 W the PWP body can shed at 25 C. Two channels loaded at once cannot both run at that level in still air, and the PowerPAD has to be soldered to a copper plane with vias for the figure to hold at all.

The supply rails set the output swing, and the swing sets the loop reach. With plus or minus 15 V the single ended swing is about plus or minus 13.3 V into 50 ohms, which is 26.6 V peak, or 53 V peak to peak differentially. With plus or minus 5 V the same measurement gives plus or minus 3.5 V, so a 50 V peak to peak differential signal is not available at all. A board specified on the headline voltage and then built with a 5 V rail loses roughly 40 dB of reach.

The differential input limit of 6 V is a real ceiling on a line interface. During a surge or a line fault the driver sees large common mode and differential excursions, and 6 V between the two inputs is well below what a transformer coupled line can present. Clamping diodes on the input pins and a series resistor ahead of them belong to the interface, not to an optional protection kit.

The 1900 V per microsecond figure is quoted at a gain of 5. At a gain of 1 the compensation and the feedback resistor change, and usable full power bandwidth falls to 30 MHz with a 20 V peak to peak output. For a 1 MHz ADSL band that is comfortable; for a wideband test head that wants 100 MHz at 10 V peak to peak it is not.

Crosstalk of minus 64 dB at 1 MHz comes with separate supply pins, and that structure only pays if each supply pin has its own decoupling capacitor at the pin. One shared 100 nanofarad capacitor across the pair lets the large signal of one channel modulate the supply of the other, and measured crosstalk then falls well short of the data sheet value.

Where this order code fits

This part sits at the remote terminal end of an ADSL or HDSL loop, where a differential pair has to deliver a 50 V peak to peak signal into a low impedance line while keeping third order distortion low enough for the constellation to close. The same drive stage appears in test equipment that needs a wideband differential output and in ultrasound pulsing where current delivery matters more than voltage accuracy. Boards comparing it with a neighbouring part start from our How to Verify a Drop in Replacement page, and boards replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

Is 200 mA or 250 mA the number to use for a load calculation? Use 200 mA, the guaranteed minimum into 50 ohms at 25 C. The 250 mA headline describes the amplifier, and 400 mA is the absolute maximum the output stage survives, not a level any board should reach.

Can the two drivers share one supply decoupling network? They can share the bulk capacitor but not the high frequency decoupling. Each VCC pin needs its own capacitor at the pin, because the separate pins exist precisely to keep the two channels from modulating each other.

What happens at plus or minus 5 V instead of 15 V? Bandwidth and distortion mostly hold, but the single ended swing falls to about plus or minus 3.5 V, so the differential reach drops from roughly 53 V peak to peak to about 14 V peak to peak.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Amplifier Cross Reference page sets out the checks that keep a substitute from failing on the bench.