Contact Us

SN65LVDS1050PWR

Brand: Texas Instruments
Texas Instruments SN65LVDS1050PWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65LVDS1050PWR — Power Management & Signal Chain | Superb Automation

SN65LVDS1050PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65LVDS1050PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65LVDS1050PWR: two LVDS channels that run from 2.4 V

The SN65LVDS1050PWR is a dual driver and receiver pair in a 16 pin TSSOP, close in function to the SN65LVDS050 but characterised over a lower supply window of 2.4 V to 3.6 V. That lower floor is the difference that matters: a board powered from a lithium cell or from a 2.5 V rail can carry an LVDS link without adding a boost converter, and the thin shrink body keeps the footprint small enough for a handheld unit.

Signalling rate is up to 400 Mbit/s, output swing is 285 mV typical into a 100 ohm load, and the bus terminals survive 12 kV of discharge. The driver takes 1.7 ns typical to propagate and the receiver 3.7 ns, with 25 mW and 60 mW of dissipation at 200 MHz. The receiver keeps a high input impedance across the supply range and provides an open circuit failsafe, so an unplugged cable is seen as a defined state rather than as noise.

Key data for the SN65LVDS1050PWR

ChannelsTwo driver and receiver pairs, 16 pins, with separate enable pins for driver and receiver
Supply2.4 V to 3.6 V, the low voltage member of the LVDS050 group
RateUp to 400 Mbit/s, ANSI TIA/EIA-644-1995 compliant
Swing285 mV typical into a 100 ohm load, 12 kV bus terminal ESD
DelaysDriver 1.7 ns typical, receiver 3.7 ns typical
Power25 mW per driver and 60 mW per receiver at 200 MHz, 5 V tolerant LVTTL inputs

Body, marking and reel data

BodyTSSOP PW, 16 pins, 20 mil lead pitch for a thin profile
Reel2000 pieces on a large reel on the plain, .B and G4 rows
MarkingDL1050 or LDS1050 depending on the marking line, both are this die
HandlingMoisture level 1, 260 C peak, unlimited floor life
TemperatureMinus 40 C to 85 C

What the 2.4 V floor changes in a portable product

A 3.3 V rail with a five per cent tolerance sits at 3.135 V at the bottom, and most LVDS parts are specified from 3.0 V or 3.3 V. A product that runs from a single cell through a 2.5 V regulator sits below that, and the usual answer is a second regulator, a level translator or a different signalling family. This part removes that decision by holding its specified behaviour down to 2.4 V, which is the discharge knee of a two cell alkaline pack and the regulated output of a 2.5 V LDO under load.

The 5 V tolerant LVTTL inputs let the logic side stay at 3.3 V or 5 V while the link runs at a lower rail. That mismatch is common in instruments where the processor is on 3.3 V and the display or the sensor head is on 2.5 V, and it avoids a level shifter on every line.

Questions to settle before the order

First, whether the 400 Mbit/s figure applies to the intended cable. It is the device limit, and a long cable at that rate needs the termination and the pair skew checked separately. Second, whether the receiver enable is needed. Both driver and receiver have enable pins, and a link that is only ever point to point can tie them active and save two control lines.

Third, the marking. Two marking variants are in circulation for the same die, so an incoming inspection that compares the printed code against a single expected string will raise false alarms. Fourth, the temperature window stops at 85 C, which rules out an automotive or outdoor enclosure without a separate grade.

Sourcing a low voltage LVDS part

This part is bought for its supply floor rather than for its speed, so the quotation always names the rail. A board that regulates to 2.5 V has about 100 mV of headroom above the 2.4 V specification at the bottom of the load step, and a board that regulates to 2.8 V has more. We ask for the rail and the tolerance before we confirm the row, because a 3.0 V minimum part would look identical on paper and fail on the first cold start.

The packing is a 2000 piece reel, which suits a run of a few hundred boards and leaves stock for a service spares order. For a product that ships for a decade, the question is not the price of the reel but whether the die stays in production, and that is where a last time buy plan and a second source belong in the conversation. We can hold a buffer against a scheduled build if the forecast is shared a quarter ahead.

For boards that are moving from a 3.3 V only part to this one, the electrical comparison is on our drop in replacement checklist. Where the supply chain question is a lead time rather than a specification, the routes we use are described on our component lead time solutions page.