SN65LVDS101DGKR
Product Specifications
SN65LVDS101DGKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65LVDS101DGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65LVDS101DGKR: a repeater that cleans up a differential link at 2 Gbps
The SN65LVDS101DGKR is a differential receiver followed by a differential driver, wired back to back as a repeater. It accepts LVDS, PECL or CML levels at rates up to 2 Gbps and repeats the signal as an LVDS or PECL output, which makes it the part that sits in the middle of a long link and restores the eye before the signal reaches the end point.
Two numbers describe why it is used. Total jitter is below 65 ps, so the repeater adds very little to the budget of the downstream receiver, and part to part skew is 100 ps maximum, so several channels repeated on one card stay aligned. The receiver has 25 mV of input hysteresis and works over a 0 to 4 V input voltage range, which means it tolerates a link whose common mode has drifted well away from the nominal point.
Key data for the SN65LVDS101DGKR
| Function | Differential receiver and driver connected as a repeater, one channel per package |
| Rate | Rated for signalling rates to 2 Gbps |
| Jitter | Total jitter below 65 ps, part to part skew 100 ps maximum |
| Inputs | LVDS, LVPECL and CML compatible, 0 V to 4 V input range, 25 mV of threshold hysteresis |
| Supply | 3.3 V single rail, with an on chip VBB bias reference for AC coupled inputs |
| Bodies | SOIC 8 and VSSOP 8, with the LVDT variant adding a 110 ohm terminating resistor |
Body, marking and reel data
| Body | VSSOP DGK, 8 pins, 3.0 mm by 3.0 mm |
| Reel | 2500 pieces on a large reel on the plain and .B rows |
| Marking | AZM printed on the VSSOP body |
| Handling | Moisture level 1, 260 C peak, unlimited floor life |
| Temperature | Minus 40 C to 85 C |
Where a repeater belongs in a rack
A signal that leaves a line card, crosses two backplane connectors and reaches a switch card has lost most of its margin at 2 Gbps. Putting a repeater at the switch card input restores the amplitude and the edge, and because the part also converts between families, the same device can take a CML output from an ASIC and drive an LVDS pair down a cable. That conversion role is often more valuable than the regeneration itself.
The VBB reference pin is the detail that saves a respin. It provides a bias voltage for AC coupled inputs, so a link that arrives through a coupling capacitor does not need an external divider. The LVDT version adds the 110 ohm termination inside the package, which removes one part from the bill of materials but also removes the option of terminating at a different point.
Selection questions before ordering
The first is whether the link needs the internal termination. If the receiver sits at the end of the cable, the LVDT version is the simpler choice. If the receiver taps a bus that continues, the plain version with external termination is the correct one. The second is the jitter budget: the repeater adds less than 65 ps, but two repeaters in series add twice, and the budget has to be counted before a third is added.
The third is the output family. The part repeats as LVDS or PECL depending on the variant, and a driver that expects PECL levels will not accept the LVDS rows. The fourth is the common mode at the input: the 0 to 4 V range is wide, but a link that floats outside it will clip the receiver.
What a repeater changes in a bill of materials
Adding a repeater to a link is not a single part decision. The part itself is small, but it needs a clean 3.3 V rail, a ground that is continuous under the pair, and a place where the trace length before and after the device can be kept short. On a card that already has an LVDS receiver, the repeater replaces the receiver rather than adding to it, because the device contains both halves.
Where the link carries several channels, the part to part skew of 100 ps maximum is the number that decides whether all channels can be repeated with one clock reference. Four repeaters in parallel will hold that skew if they come from the same reel, and mixing reels from two production lots burns most of the margin. We quote this family in reel quantities for that reason and keep lot identity on the packing list.
Part numbers in this family are often cross sourced when a board is refreshed, and the comparison work is described on the pin to pin cross reference page. Where the original code has gone end of life, the replacement route is set out on our obsolete part cross reference hub.A full reel is 2500 pieces, and a rack build of fifty cards uses a fraction of it, so the balance is stored sealed with its date code and its lot number recorded.