Contact Us

SN65LVDS100DR

Brand: Texas Instruments
Texas Instruments SN65LVDS100DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65LVDS100DR — Power Management & Signal Chain | Superb Automation

SN65LVDS100DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65LVDS100DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65LVDS100DR: differential repeater that regenerates an LVDS, PECL or CML signal above 2 Gbps

SN65LVDS100DR is a high speed differential receiver followed by a differential driver on one die, wired as a repeater so a signal can be cleaned and re driven without changing its logic sense in a SOIC body of 8 pins. It accepts LVDS, LVPECL or CML levels on the input pair over a 0 V to 4 V common mode window, repeats them as LVDS, and carries a total jitter below 65 ps with a part to part skew limit of 100 ps and 25 mV of input hysteresis. The supply is 3 V to 3.6 V, the propagation delay is 470 ps typical, and the same die is offered with the 110 ohm termination inside the package, which is the difference between the LVDS and LVDT letters in the string.

Order code and package

SN65LVDS100DRSOIC D body, 8 pins, 2500 pieces on a large reel, Active in the addendum dated 10 August 2026, NIPDAU finish, moisture level 1 with no floor life limit, minus 40 to plus 85 degrees
SN65LVDT100the same repeater with the 110 ohm input termination inside the package, which removes two resistors and the stub they create, and is the member to quote when the input pair arrives on a connector
SN65LVDS101the same idea with a PECL output rather than an LVDS output, for a backplane that still runs emitter coupled logic levels and needs a translator rather than a repeater
SN65LVDT101PECL output with the internal termination, the fourth row of the same family, so the four strings differ only in output standard and in whether the termination is inside
SOIC against VSSOPboth bodies are printed in the addendum at 2500 pieces and the VSSOP is 3.00 mm by 3.00 mm against 4.90 mm by 3.91 mm, so the smaller body is a board area decision and not an electrical one

Electrical parameters that decide the application

Signalling ratebuilt for rates at or above 2 Gbps, which is the figure the vendor prints in the features list and the one to quote against a serial link budget
Total jitterbelow 65 ps, measured at the output, so a link that is already at the edge of its eye diagram gains margin rather than losing it through the repeater
Part to part skew100 ps maximum, which is the number that decides whether six repeaters on one backplane stay inside a lane to lane alignment budget
Input hysteresis25 mV over an input voltage range of 0 V to 4 V, which is what stops a slow or attenuated edge from producing more than one transition at the output
Propagation delay300 ps minimum, 470 ps typical and 900 ps maximum, so a repeater adds under a nanosecond and the link budget can treat it as a fixed delay rather than as a variable
Pulse skew5 ps typical and 50 ps maximum between the rising and falling path, which keeps the duty cycle of a clock close to fifty per cent through the repeater
Differential output475 mV minimum, 575 mV typical and 750 mV maximum into a 50 ohm load returned to VCC minus 2 V, which is the LVDS window and the reason the output can drive a standard receiver
Supply3 V to 3.6 V with a 3.3 V nominal, and the supply current sits at 25 mA typical for the 100 members, which is the price of an always on repeater against a mux
Input standardLVDS, LVPECL and CML levels are all inside the window, so one part covers three interfaces and the choice of upstream driver does not force a second part number
Reference outputthe VBB pin holds a voltage 1.35 V below VCC, typically, for biasing a PECL input that is driven single ended or AC coupled, which is one resistor pair saved per port
Temperatureminus 40 to plus 85 degrees on every row of the family, which is the commercial and industrial middle ground rather than the 125 degree range some of the interface families carry
Ordering precisionthe D body is SOIC and the DGK body is VSSOP, and both are printed at 2500 pieces in this addendum, so the letter after the base number decides the footprint and nothing else

Family variants and how they differ

LVDS100 against LVDT100the T adds an internal 110 ohm termination across the input pair. On a short board trace the external resistors are easy; on a signal that arrives through a connector the internal termination removes a stub and improves the eye
100 against 101the 101 repeats to PECL rather than LVDS. A backplane built around emitter coupled logic needs the 101 at the receiving end, and the rest of the electrical table is the same
Against a redriver with equalisationan equalising redriver compensates for a long lossy channel and costs several times as much. This part repeats, it does not equalise, so a channel with 20 dB of loss at the Nyquist frequency needs the more expensive device
Against a clock buffera fanout buffer distributes one clock to many loads with matched delays. This part is a one to one repeater, so a fanout requirement is a different part number and a different jitter budget
Against an AC coupling capacitora capacitor passes the signal and does not restore its amplitude or its edges. Where the eye is still open, a capacitor is cheaper; where the eye is closing, only the repeater helps

Points to check before this part goes on a BOM

The output standard is fixed by the device, not by the input. A CML driver feeding this part produces an LVDS output, and an LVDS driver produces the same output. That is convenient and it is also the trap: a link that was CML end to end becomes LVDS at this point, and the receiving end has to accept LVDS. A customer replacing a passive AC coupling block with this part has to check the far end, not the near end.

The 25 mV of hysteresis is the number that matters on a long trace. Below that, an attenuated edge with noise on it can cross the threshold more than once and the repeater produces a burst of transitions rather than one. Above it, a genuinely small differential signal is not seen at all. The 0 V to 4 V input window and the 25 mV hysteresis together define the usable input amplitude, and a link with 100 mV of differential swing at the receiver is comfortable while one with 30 mV is not.

The VBB reference is a convenience with a current limit. It holds 1.35 V below VCC and is meant to bias an unused or a single ended PECL input through a resistor, with the current kept small. A customer who uses it to power something else, or who loads it with a second port, finds the reference moving and the input threshold with it. The datasheet gives the sourcing and sinking limit around 400 uA and 12 uA, and that is a bias, not a supply.

The 100 ps part to part skew limit is what makes this part usable in a parallel bus. Six lanes repeated through six packages hold their relative alignment to within 100 ps, which is a fifth of a bit at 2 Gbps. What the number does not cover is the difference in trace length on the board between the six packages, and that is where a lane to lane budget usually goes wrong: the part is fine and the routing is not.

Jitter below 65 ps is a total figure that includes the random and the deterministic parts at the stated rate. A repeater cannot remove jitter that is already in the data; it adds its own and passes the rest. A link at the edge of its budget therefore needs the source cleaned rather than another repeater inserted, and a chain of three repeaters is a chain of three additive jitter terms.

The supply current is 25 mA typical for the 100 member and roughly double for the 101, because the PECL output stage draws a constant current that the LVDS output does not. A board with twenty four repeated lanes on the 101 member is a 1.2 A load at 3.3 V, which is not a detail to discover at the thermal stage of a build.

Why a repeater and not a buffer

A repeater receives, restores the amplitude and the edge rate, and drives the signal on with the same logic sense. A buffer with a fanout drives several loads from one input pair, which is a different function with a different delay match requirement. The 100 and 101 members are one to one repeaters, and the reason to use one is that the signal has been through a connector, a cable or a long trace and no longer meets the input requirements of the next device.

The classic place for this part is a backplane interface card where the incoming pair has travelled through two connectors. The eye at the card edge is smaller than the eye at the driver, and repeating it once inside the card restores the margin for the rest of the board. Where the loss is in the cable rather than the board, the equalising redriver is the correct device and this one is not.

Reading the order code

SN65LVDS100 breaks down as the family, LVDS for the output standard and 100 for the member without an internal termination. The T in the LVDT string adds the termination, the 101 changes the output to PECL, and the D or DGK at the end of the orderable string selects SOIC or VSSOP. There is no speed suffix and no temperature suffix, so a buyer comparing rows is choosing between output standard and body size only.

Where this order code fits

Wireless and telecom infrastructure, printers and any backplane card that receives a differential pair through a connector are the stated applications, and the common thread is a signal that has to be restored after a channel has taken its toll. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Does the repeater change the signal standard? Yes. The input can be LVDS, LVPECL or CML and the output is fixed by the device, LVDS on the 100 and PECL on the 101, so the far end has to accept the output standard.

Can it drive more than one receiver? It is a one to one repeater with a single output pair. A fanout requirement needs a buffer, which is a different part with a different delay match specification.

Is the internal termination the only difference between the LVDS and LVDT rows? Yes. The electrical table is the same and the T adds the 110 ohm resistor across the input pair inside the package.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.