Contact Us

SN65LBC179DR

Brand: Texas Instruments
Texas Instruments SN65LBC179DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65LBC179DR — Power Management & Signal Chain | Superb Automation

SN65LBC179DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65LBC179DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65LBC179DR: a full duplex RS-485 driver and receiver in eight pins

The SN65LBC179DR puts one differential line driver and one differential line receiver in a single eight pin body. The driver outputs and the receiver inputs sit on separate terminals, which is what makes full duplex operation possible: the transmitter talks on one pair while the receiver listens on the other pair at the same time. Both blocks are built on the same die and share the 5 V rail.

The electrical behaviour follows ANSI RS-485 and ISO 8482:1987(E). The receiver handles a common mode window of minus 7 V to plus 12 V, so two units sitting on different ground potentials can still exchange data over a long cable. The driver output is current limited in both directions, and a thermal shutdown block turns the driver off at roughly 172 C junction temperature. That combination is what keeps a miswired bus from destroying the part during a service visit.

Key data for the SN65LBC179DR

FunctionOne differential driver plus one differential receiver, separate bus terminals for full duplex traffic
StandardsMeets or exceeds ANSI RS-485 and ISO 8482:1987(E) requirements
SpeedOperates with pulse widths as low as 30 ns, driver propagation delay 15 ns typical and 30 ns maximum
Common modeReceiver input range minus 7 V to plus 12 V, receiver hysteresis 45 mV typical
SupplySingle 5 V rail, supply current 4.2 mA typical and 5 mA maximum with no load
ProtectionPositive and negative output current limiting, driver thermal shutdown near 172 C junction

Body, marking and reel data

BodySOIC D, 8 pins, 4.9 mm by 3.91 mm, the narrow body that fits a legacy SN75179B footprint
Reel2500 pieces on a large reel for the plain row, and the same 2500 on the .A and G4 rows
Marking6LB179 on the SOIC rows, which is what a receiving inspection has to match against the order
HandlingMoisture level 1, 260 C peak reflow, unlimited floor life, so no bake is needed before assembly
TemperatureMinus 40 C to 85 C for the SN65LBC179, and the Q suffix covers minus 40 C to 125 C

Where a full duplex pair still earns its place

Half duplex transceivers dominate because they use one pair of wires. A full duplex pair is the right answer when the protocol needs the receiver to stay live while the driver is talking: motion control loops that stream position while accepting a new setpoint, weigh scales that report continuously and also take a tare command, and older industrial buses that were wired as four wire RS-422 and later moved to RS-485 levels. In those cases one eight pin part replaces a transceiver plus an external receiver, and the board keeps a single footprint.

The bus loading behaviour matters when a unit is powered down on a live bus. The driver and receiver inputs present minimum loading when VCC is at 0 V, so pulling the supply on one node does not drag the whole segment down. That is the property to check when a rack allows a board to be swapped while the loop stays energised.

Questions that come with this code on a BOM

The first question is usually about the Q suffix. The plain SN65LBC179 is characterised from minus 40 C to 85 C, while the Q version is characterised to 125 C. A cabinet that runs hot, or a product that has to pass a 105 C ambient test, needs the Q row and that is a different line on the order.

The second question is about termination. The part does not contain a terminating resistor, so the two ends of the segment still need their own resistors, and stub lengths have to stay short at the data rates this part supports. The third is about the failsafe state: with no input difference the receiver output is not defined by the part alone, so a bus that can go idle needs bias resistors or a protocol that never leaves the pair floating.

How this line is quoted and shipped

Quotations for this code are built from the grade and the packing rather than from the part number alone. The industrial row and the Q row carry different characterisation, and the reel is the same 2500 pieces on both, so the two lines differ only in temperature. We quote the grade the drawing asks for and state the alternative, so a buyer can see the cost of the wider window before a change is raised.

On the goods side, the check is the marking against the order and the date code against the shelf life. A Level-1 part needs no bake, and that is worth knowing when a line brings a partial reel to the floor. For a production order we confirm the reel size and the carrier width in writing, because a 2500 piece reel and a tube of 50 pieces are not interchangeable on a feeder.

Projects that are second sourcing an SN75179B socket can treat this as a pin compatible drop in, and the check is the temperature grade and the marking rather than the pinout. Projects that are pulling an older interface part out of a long life product will find the cross reference work in our pin to pin cross reference page, and the handling of the last time buy sits on our last time buy and LTB planning page. Send the BOM line and the quantity and we will come back with the grade, the reel and the date code window.