SN65LBC176DR
Product Specifications
SN65LBC176DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65LBC176DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65LBC176DR: 5 V RS-485 transceiver that has stayed in production since 1990
SN65LBC176DR is a bidirectional differential bus driver and receiver on a 5 V rail, built to the RS-485 and ISO 8482 standards and used where a 5 V bus has to keep working for a decade without a firmware change in a SOIC body of 8 pins. It is a single 5 V part with a three state differential driver and a differential receiver, receiver sensitivity of plus or minus 200 mV and 50 mV of typical hysteresis, thermal shutdown, positive and negative current limiting on the driver, a disabled supply current of 200 uA maximum, a common mode range of minus 7 V to plus 12 V, and glitch free behaviour on power up and power down. The driver differential output delay is 8 ns typical and 25 ns maximum into 54 ohm with 50 pF, and the enable times are 35 ns, which is why the part is still used on parallel and serial buses that need tight skew.
Order code and package
| SN65LBC176DR | SOIC D body, 8 pins, Active in the addendum dated 10 August 2026, 2500 pieces on a large reel, NIPDAU finish, moisture level 1 with unlimited floor life, minus 40 to plus 85 degrees |
| Part marking | the plain DR row prints 9318301QPA and the DRG4 row prints 6LB176, so two reels of the same electrical part can arrive with two different top marks and an incoming inspection that keys on the mark will reject one of them |
| SN65LBC176D and PDIP | the tube and through hole rows, for a repair or a legacy board that still has a socket. The PDIP body is 9.81 mm by 6.35 mm |
| SN55LBC176 and SN75LBC176 | the military temperature and the commercial temperature members of the same family. The 55 is the LCCC and CDIP part, the 75 stops at 70 degrees, and the 65 on this page is the minus 40 to plus 85 industrial one |
| SN65LBC176Q | the automotive qualified member of the family, printed in the same document and listed with the Q temp option in the same table |
Electrical parameters that decide the application
| Supply | a single 5 V rail, which is what keeps this part in production: a large installed base of 5 V industrial controllers has no 3.3 V rail to switch to |
| Standards | TIA/EIA-485-A and ISO 8482:1987(E) are both named in the feature list, and the driver meets the differential output requirements of TIA/EIA-485-A above 0 degrees only, which the datasheet states in a footnote |
| Receiver sensitivity | plus or minus 200 mV maximum, the standard RS-485 threshold, with 50 mV of typical hysteresis for noise rejection on a long pair |
| Common mode | minus 7 V to plus 12 V on the bus terminals, the full RS-485 window, so a ground potential difference between two cabinets stays inside the part rather than on the connector |
| Driver delay | 8 ns typical and 25 ns maximum differential output delay into 54 ohm with 50 pF, and 12 ns of pulse skew, which is a tight enough window for parallel bus use |
| Enable times | 35 ns to enable to either level and 60 ns to disable from a high level, which is fast enough that the part can share a bus with a processor that turns the driver on per byte |
| Current limiting | positive and negative output current limiting on the driver, so a shorted pair pulls a bounded current instead of the supply rail |
| Disabled current | 200 uA maximum with driver and receiver disabled, which is what makes a multidrop node that is not transmitting cheap to keep powered |
| Thermal shutdown | on the driver, with the junction protected against a sustained short at high ambient |
| Fail safe | open circuit fail safe receiver, so an unplugged connector produces a defined output rather than noise |
| Power sequencing | glitch free on power up and power down, so a card inserted into a live rack does not drive the bus |
| Temperature | minus 40 to plus 85 degrees on this string, with the 55 and 75 members covering the military and commercial ends of the same family |
Family variants and how they differ
| LBC176 against LBC176A | the A suffix is a later die with the same pinout and the same 5 V rail but a different differential output specification. A substitution between them changes the margin on a long bus |
| LBC176 against the 3.3 V family | the SN65HVD72 family runs on 3.3 V with IEC level ESD ratings and a wider temperature range. It is the part for a new board, and the LBC176 is the part for a board that cannot change its rail |
| LBC176 against LBC174A | the 174 is a quad driver with no receiver, for a parallel bus that needs four differential outputs. The 176 is one driver and one receiver, the transceiver for a two wire port |
| Against an isolated transceiver | an ISO3082 class part isolates the port and needs an isolated supply. A 5 V bus inside one cabinet does not need the barrier |
| Against a modern 5 V part | a 65HVD3082E class device is a lower power 3.3 V or 5 V part with a shutdown mode. The LBC176 is chosen when the existing board and the existing firmware are fixed |
Points to check before this part goes on a BOM
The footnote on the driver output is the most important line in the document for anyone using this part below freezing. The minimum differential output may not fully comply with TIA/EIA-485-A at operating temperatures below 0 degrees, and the vendor says so in a note rather than in the feature list. A product rated to minus 40 that has to meet the standard at the cold end needs the margin checked on a cold chamber, not assumed from the headline.
The marking difference between the plain and G4 rows is a production problem rather than an electrical one. The plain row prints an OEM style mark and the G4 row prints 6LB176, and both are the same silicon from the same reel family. A customer whose incoming inspection compares the top mark against a drawing will need both marks on the approved document, or the second shipment will sit in quarantine.
The 8 ns typical driver delay is why the part is still used on parallel buses after three decades. A modern transceiver with the same delay costs less, but the LBC176 is already qualified in the customer's product, and requalification costs more than the price difference. That is the ordinary reason a 1990 data sheet is still revised in 2022.
The 200 uA disabled current applies with both the driver and the receiver disabled. A node that keeps the receiver enabled to listen for its address draws the operating current instead, and the difference on a 32 node bus is what decides the size of the 5 V supply. The datasheet print both figures, and the operating one is the one to use for a listening node.
The thermal shutdown protects the driver and not the receiver. A bus that is shorted while the node is only listening stays functional, which is correct behaviour and is often reported as a part that works until it tries to talk. A field report of that shape points at the pair, not at the transceiver.
The family spans military and commercial temperature grades in one document, and the suffix decides which one ships. A 5962 style part number on a military drawing is not interchangeable with the industrial string even when the die is the same, because the test flow and the traceability differ.
Why a 5 V bus is still specified
A large installed base of industrial controllers, drives and meters runs on a 5 V rail and has an RS-485 port that works. The cost of moving that product to 3.3 V is a new board, a new qualification and a new firmware image, and the cost of keeping the 5 V transceiver is the price of one part. That trade is why the 5 V family is still active and still receiving document revisions.
The other reason is the common mode window. A 5 V transceiver has more headroom above the rail than a 3.3 V one, and on a long run between two buildings with a ground difference the extra headroom is the difference between a working link and an intermittent one. A 3.3 V part with an isolated barrier is the modern answer, and it is a bigger change than a part substitution.
What the order code decides
The string reads SN65LBC176 for the device, D for the SOIC body and R for the large reel of 2500. The G4 suffix is the lead free declaration row and carries a different top mark. The 55 and 75 prefixes are different temperature grades in the same document, and the Q suffix on the plain number is the automotive grade, so none of these positions can be changed without buying a different part.
Where this order code fits
Multipoint bus transmission in noisy environments, parallel and serial links, and long bus lines in industrial cabinets are the applications the vendor prints, and a 5 V retrofit port on an installed controller is the case this part is bought for. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.
Questions buyers ask
Does SN65LBC176DR meet RS-485 at minus 40 degrees? The driver meets the TIA/EIA-485-A differential output requirements above 0 degrees according to the datasheet footnote. Below that the minimum output may not fully comply, so a cold chamber check is needed for a product rated to minus 40.
How much current does it draw when disabled? 200 uA maximum with driver and receiver both disabled. A listening node keeps the receiver on and draws the operating current instead.
What is the reel size? 2500 pieces on a large reel for the DR row, NIPDAU finish, moisture level 1, minus 40 to plus 85 degrees.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.