Contact Us

SN65HVD76DGSR

Brand: Texas Instruments
Texas Instruments SN65HVD76DGSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD76DGSR — Power Management & Signal Chain | Superb Automation

SN65HVD76DGSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD76DGSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD76DGSR: a 50 Mbps full duplex RS-485 transceiver with enable pins

The SN65HVD76DGSR is the fastest enabled member of the SN65HVD7x family: a 3.3 V full duplex RS-485 transceiver rated to 50 Mbps, with an active high driver enable and an active low receiver enable so the node can release the pair when it is not talking. It comes in a DGS VSSOP 10 body, which is the ten pin version that carries both enables plus the separate driver and receiver pins.

The electrical and protection figures match the rest of the family: above 30 kV HBM, above 12 kV IEC 61000-4-2 contact discharge, above 4 kV fast transient burst, 70 mV of receiver hysteresis, below 1.1 mA quiescent and a standby current of 10 nA typical with under 5 uA maximum when both halves are disabled. The 1/8 unit load option allows 256 nodes on a segment.

Key data for the SN65HVD76DGSR

RateUp to 50 Mbps, the top of the family, against 20 Mbps on the 73 and 74 and 400 kbps on the 70 and 71
EnablesActive high driver enable and active low receiver enable, so the transceiver can be parked between messages
Loading1/8 unit load option, up to 256 nodes on one bus segment
ProtectionAbove 30 kV HBM, above 12 kV IEC 61000-4-2 contact, above 4 kV IEC 61000-4-4 burst
Receiver70 mV hysteresis, wide common mode range, glitch free power up and power down for hot plugging
CurrentBelow 1.1 mA quiescent, 10 nA typical standby and under 5 uA maximum with both halves disabled

Body, marking and reel data

BodyDGS, VSSOP 10 at 3.00 mm by 3.00 mm, the ten pin body that carries both enables
Reel2500 pieces on a large reel, carrier tape 12.4 mm, 330 mm reel
Tube rowsThe DGS tube rows publish around 75 to 80 pieces, which is a hand assembly quantity rather than a line quantity
Body noteThe .A row of the DGS string prints an 8 pin body and the .B row prints a SOIC D body, so the suffix and the body do not line up in the vendor file
TemperatureMinus 40 C to 125 C on every published row of the family

When 50 Mbps and an enable pin are both needed

A multi drop bus at high rate is the case this part was built for. The node has to be able to stop driving the pair so another node can talk, and at 50 Mbps the window between messages is short, so the enable path has to be fast and clean. The active low receiver enable lets the controller park the receiver as well, which drops the current to the standby figure and keeps the bus quiet during an image load.

The 50 Mbps rate is only usable over a short pair. At that speed the bit time is 20 ns, and a few metres of cable with a stub is enough to close the eye. Boards that need 50 Mbps usually place the transceivers within one enclosure or across a backplane connector, and they terminate at both ends with 120 ohm resistors that match the pair. The enable path also has to be short: a driver that turns on while another node is still finishing a byte will corrupt the frame, so the controller has to gate the enable on the bus idle state and not only on its own transmit flag.

Questions we get when this code is on a BOM

Most questions are about the enable polarity. The driver enable is active high and the receiver enable is active low on this member, which is the opposite of the 70 and 73 in the same family. A board that was laid out for one polarity and fitted with the other will hold the driver on permanently and collide with the bus, so the polarity is the first thing we confirm.

The second question is about the body. The DGS body has ten pins and the D body has eight, and the two are not interchangeable without a land pattern change. The order string ends in DGSR, so the ten pin body is the one to expect, and we say so on the offer rather than letting the warehouse pick the eight pin row.

How SUPERB supports this line item

We supply the SN65HVD76DGSR with the body, the enable polarity and the reel quantity stated, because the vendor file mixes 8 pin and 10 pin rows under the same string. Customers comparing the 20 Mbps and 50 Mbps members can use our pin to pin cross reference page, which sets out the pin count and enable differences.

For backplane links where the transceiver sits next to a connector, the one stop BOM sourcing route lets the interface parts, the termination resistors and the connector arrive on one order with date codes declared.