Contact Us

SN65HVD75DGKR

Brand: Texas Instruments
Texas Instruments SN65HVD75DGKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD75DGKR — Power Management & Signal Chain | Superb Automation

SN65HVD75DGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD75DGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD75DGKR: 20 Mbit/s RS-485 transceiver in a 3 mm VSSOP body

SN65HVD75DGKR is a 3.3 V half duplex RS-485 differential transceiver in a VSSOP body of 8 pins. It drives and receives a two wire RS-485 bus at 20 Mbit/s from a 3.3 V rail and carries 80 mV of receiver hysteresis for noise rejection. The DGKR order code is the 8-pin VSSOP measuring 3.00 mm by 3.00 mm, and the same die is offered in SOIC and VSON bodies for boards that cannot take the small package.

Order code and package

Order codeSN65HVD75DGKR
Package8-pin VSSOP, DGK body, 3.00 mm by 3.00 mm
Packingtape and reel
Bushalf duplex, A and B differential pair
LogicD, DE and RE, with R as the receiver output
Signaling rate20 Mbit/s on this member of the family
Node loadinglow unit load, over 200 nodes on one bus

Electrical parameters that decide the application

Supply3 V to 3.6 V, 3.3 V nominal
Differential output1.5 V minimum into a 54 ohm load, 2 V typical
Receiver hysteresis80 mV typical, 50 mV minimum
Receiver thresholdminus 200 mV to minus 20 mV positive going
Common mode rangeminus 7 V to plus 12 V
Quiescent currentunder 1 mA with the driver and receiver enabled
Standby currentunder 2 microampere with both disabled
ESDplus or minus 15 kV HBM and plus or minus 12 kV IEC contact on the bus pins

Family variants and how they differ

SN65HVD72250 kbit/s version with a 4 microsecond bit time
SN65HVD7520 Mbit/s version with a 50 ns bit time, the part on this page
SN65HVD7850 Mbit/s version for short backplanes
BodiesD SOIC, DGK VSSOP and DRB VSON of the same die

Points to check before this part goes on a BOM

The bit time at 20 Mbit/s is 50 ns, and the driver propagation delay is specified from 7 ns to 17 ns with 2 ns of pulse skew. Adding the receiver delay on the far node and the cable delay of about 5 ns per metre, a 20 Mbit/s link is a backplane part rather than a field bus part: the round trip timing budget runs out at a few metres.

The 80 mV of hysteresis is the reason a slow moving or noisy differential signal does not produce bursts of edges at the receiver output. It also sets the minimum signal the bus has to deliver: a differential amplitude that falls below about 100 mV at the far end of a long cable sits inside the threshold window and the receiver output becomes indeterminate.

The 1.5 V minimum differential output into 54 ohm is measured with the standard RS-485 load, which is two 54 ohm resistors and a 50 pF capacitor. A bus terminated with 120 ohm at both ends presents 60 ohm and a slightly higher swing, so the load in the table is the harder case rather than the easier one.

The standby current under 2 microampere is the figure that matters in a battery instrument that keeps the bus wired while the product sleeps. A board that pulls DE high and leaves RE low keeps the receiver live and draws about 600 microampere instead, so the standby number belongs to a state the firmware has to enter deliberately.

The ESD rating on the bus pins is plus or minus 15 kV HBM and plus or minus 12 kV IEC contact discharge, and the family also carries a 4 kV fast transient burst rating. Those numbers describe the pins, not an unprotected cable in a factory; a surge that arrives with kilovolts of energy still needs a TVS array and a series element between the connector and the part.

The receiver threshold window is minus 200 mV to minus 20 mV, which is the RS-485 fail safe arrangement for a terminated but undriven bus. A bus with no termination resistors and no bias network sits at 0 V differential, outside that window, and the receiver output goes high or low on noise. The bias resistors are a board decision and not a part feature.

Thermal shutdown at about 170 degrees protects the driver against a shorted bus. In a 8-pin VSSOP the junction to ambient resistance is 168.7 degrees per watt, which is the highest of the three bodies, so a fault that keeps the driver on for seconds heats the small package faster than the SOIC version and the shutdown is what saves it.

The 200 node figure comes from the receiver input resistance, not from the driver. Each node loads the bus by a fraction of a unit load, so a bus can carry more receivers than the classic 32 node limit, but the driver still has to produce 1.5 V into a bus whose parallel termination and leakage have to be added up. A 200 node segment needs repeaters for other reasons long before the electrical limit is reached.

Driver enable and receiver enable are separate pins on an 8-pin body, and the turnaround time is set by firmware rather than by the part. A node that enables the driver while the previous talker is still driving sees a bus contention that looks like a fault and is really a software race. The minimum time to wait is one bit time plus the driver disable delay of the other node, which is published in its own data sheet and not in this one.

The 54 ohm load in the differential output specification is two 54 ohm resistors with a 50 pF capacitor, the standard RS-485 test load. A product that terminates with 120 ohm at both ends sees 60 ohm and a slightly larger swing, so passing the test load is the conservative case, not the worst case for ringing.

Fail safe biasing is a board decision. The receiver threshold window of minus 200 mV to minus 20 mV makes a terminated but undriven bus read as idle, and a bus without terminators sits at 0 V and does not. A small pull up on A and pull down on B fixes that and costs a milliamp of standby current per node.

Where this order code fits

It is used in factory automation, motion control, power meters and telecom shelves where a 3.3 V controller talks to a multi drop RS-485 segment. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Can the 20 Mbit/s part replace a 250 kbit/s part? Electrically yes, and it is the direction that is safe: a faster transceiver works at a slower rate. The reverse is not true, so a board built for a low rate part cannot be upgraded by fitting this reel without checking the cable and the termination.

Why does the receiver threshold sit below zero volts? That is the RS-485 fail safe window. A terminated bus with no active driver sits near 0 V differential, and the minus 20 mV upper edge makes the receiver read that state as a defined idle rather than as noise.

Is the VSSOP body a problem for hand assembly? The 0.65 mm pitch on the DGK body is solderable by hand with drag soldering, but the SOIC body of the same die is the easier part for a repair bench. Both are the same electrical part.

What ends a 20 Mbit/s link? Cable length and termination, not the transceiver. At 50 ns per bit the round trip has to fit inside one bit, so a few metres of cable with correct termination is the practical ceiling.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.