SN65HVD72DRBR
Product Specifications
SN65HVD72DRBR
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65HVD72DRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65HVD72DRBR: 3.3 V RS-485 transceiver at 250 kbps in the 3 mm SON body
SN65HVD72DRBR is a half duplex differential driver and receiver on a single 3.3 V rail, with IEC level ESD protection on the bus pins and a receiver hysteresis wide enough to hold a long, slow bus in a SON body of 8 pins. It runs at 250 kbps, the slowest of the three members in its family, over a common mode window wide enough for long cable runs, with more than plus or minus 15 kV human body model protection, more than plus or minus 12 kV IEC 61000-4-2 contact discharge, more than plus or minus 4 kV IEC 61000-4-4 fast transient burst, an 80 mV receiver hysteresis, and a quiescent current under 1 mA. It loads the bus lightly enough to allow more than 200 connected nodes, and the logic pins take 5 V levels so a 5 V controller can drive it without a shifter.
Order code and package
| SN65HVD72DRBR | SON DRB body, 8 pins, 3 mm by 3 mm, Active in the addendum dated 10 August 2026, 3000 pieces on a large reel, NIPDAU finish, moisture level 1 with unlimited floor life, minus 40 to plus 125 degrees, marking HVD72 |
| SN65HVD72DRBT | the same body on a 250 piece small reel, which is the row a prototype or a repair order comes from when 3000 pieces is not a quantity the line can absorb |
| SN65HVD72DR | the SOIC D body at 2500 pieces on a large reel, for a board that was routed for the wider outline and has to keep the same footprint through a second source |
| SN65HVD75 and SN65HVD78 | the same silicon at 20 Mbps and 50 Mbps. The pinout and the protection are identical, and only the driver edge rate and the receiver bandwidth change, so a bus that has to be upgraded for a new protocol is a part number change on one line of the bill of materials |
| Against the older 5 V family | a 75176 class part needs a 5 V rail and has no IEC contact discharge rating. The 3.3 V rail plus the IEC numbers is the reason this family replaced the older one in new industrial boards |
Electrical parameters that decide the application
| Supply | a single 3.3 V rail, with the logic inputs tolerant of 5 V, so the same part sits behind a 3.3 V microcontroller and behind a 5 V one |
| Signalling rate | 250 kbps on this member, which is the rate that a 1200 m run at 120 ohm termination supports without a repeater, and the reason it is the part chosen for a meter network rather than for a backplane |
| Node count | more than 200 nodes because the bus loading is a fraction of a unit load, which removes the repeater from a long multidrop trunk |
| ESD | more than plus or minus 15 kV human body model, more than plus or minus 12 kV IEC 61000-4-2 contact discharge and more than plus or minus 4 kV IEC 61000-4-4 fast transient burst, all three printed as bus pin ratings rather than board level claims |
| Hysteresis | 80 mV of receiver hysteresis, which is the number that keeps a slow, attenuated edge at the far end of a long cable from producing two counts per transition |
| Quiescent current | under 1 mA during operation and under 2 uA in standby, so a port that stays powered overnight costs less than a milliwatt |
| Common mode | wide enough for a long run between buildings with a ground potential difference, and the receiver stays inside its specified window across the full minus 40 to plus 125 degree range |
| Driver output | specified into the standard 54 ohm test load, which is what a terminated pair looks like to the driver at the near end |
| Fail safe | the receiver holds a defined output with the bus open, shorted or idle, so a controller does not see a false start bit when a connector is pulled |
| Power sequencing | glitch free on power up and power down, so a node inserted into a live bus does not drive the pair while its rail is still rising |
| Package | the DRB body is 3 mm by 3 mm, which is half the board area of the SOIC and the reason it appears on modules that have no room for an eight pin SOIC |
| Temperature | minus 40 to plus 125 degrees on every printed row, which is 40 degrees beyond the plain industrial parts and the number a cabinet mounted in a tropical enclosure needs |
Family variants and how they differ
| 72 against 75 | the same silicon at 250 kbps and 20 Mbps. The faster member has a driver edge rate that needs a short, well terminated bus, so moving up is a change to the cable and the termination as much as to the part |
| 72 against 78 | the 78 is 50 Mbps and is the part for a backplane or a short cabinet link. At 250 kbps the extra bandwidth buys nothing and costs emissions |
| Against an isolated part | an ISO1450 class device puts a barrier in the package, needs an isolated supply, and removes the ground difference problem. A run inside one cabinet does not need it |
| Against a fault protected part | the SN65HVD1794 survives 70 V on the bus pins and this part does not. A bus that can be miswired to a supply rail needs the fault rating, and a bus that is wired once and tied down does not |
| Against a 5 V transceiver | no level shifting, one rail instead of two, and the same 8 pin outline. The only thing given up is the 5 V common mode headroom, which matters only on a very long run |
Points to check before this part goes on a BOM
The three protection numbers are printed with a greater-than sign and each one covers a different event: the human body model covers a technician handling a cable, the IEC contact discharge covers a charged connector shell touching a pin, and the fast transient burst covers a contactor or a relay in the same cabinet. A customer who asks whether the port is protected usually means the third one, and it is the one a plain transceiver does not carry.
The 80 mV hysteresis is the quiet reason this part works at 1200 m and a cheaper part does not. Attenuation on a long cable rounds the edges and slows them, and a receiver with 20 mV of hysteresis counts the noise on a slow edge as extra transitions. The vendor prints the hysteresis in the feature list because it is a system level property, not a detail.
The 250 kbps ceiling is not a limitation of the silicon, it is the rate the cable supports. A customer who needs 1 Mbps at 1200 m is asking for a cable that does not exist, and the honest answer is a repeater or a different physical layer. Quoting a 20 Mbps member for that run produces a link that fails intermittently in wet weather.
The DRB body is a SON with the pads under the package, so the solder joint is not visible after reflow and the footprint has to be checked against the vendor drawing rather than copied from the SOIC. Boards that were laid out for the SOIC and then changed to the SON usually keep the same pin order but need a different stencil aperture, and that is a production note rather than an electrical one.
The quiescent current under 1 mA is what makes a 3.3 V port viable on a solar or battery fed node, and it holds in the standby state at under 2 uA. The figure that is usually missed is the driver current in the dominant state, which follows the bus load, so a bus with a short across it draws the current limit rather than the quiescent figure.
The part does not test or guarantee the bus. A port that reports a fault has to detect it with the controller, and the fail safe receiver only guarantees a defined level with the bus open, shorted or idle. Any diagnostic claim on a data sheet page belongs to the firmware that reads the receiver, not to the transceiver.
Why the SON body is on this line
The DRB outline is 3 mm by 3 mm with the leads folded under the body, which saves about half the board area of an eight pin SOIC and shortens the stub from the pin to the connector. On an RS-485 port the stub length is part of the signal path, so the smaller body is not only a space decision.
The trade is inspection. A SON joint cannot be seen from the side, and a board that goes through a reflow profile built for the SOIC sometimes shows a void under the thermal pad. The vendor drawing gives the pad geometry and the paste ratio, and a customer moving from the SOIC should treat the first build as a process qualification rather than a drop in.
What the order code decides
The string reads SN65HVD72 for the device, DRB for the SON body and R for the large reel of 3000. The T in the same position is the 250 piece small reel, and the plain DR string is the SOIC body. Nothing in the string selects the data rate, because the rate is set by the device number, so a purchase order that changes 72 to 75 by hand is buying a different part with the same outline.
Where this order code fits
Factory automation, telecommunications infrastructure and motion control are the applications the vendor lists, and a metering or building bus that runs several hundred metres at low rate is where this member earns its place. Teams comparing it with a neighbouring part start from our Component Lead Time Solutions page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
What data rate does SN65HVD72DRBR support? 250 kbps. The same family is offered at 20 Mbps as the SN65HVD75 and at 50 Mbps as the SN65HVD78, with the same pinout and the same protection.
How many nodes can one bus carry? More than 200, because the bus loading is a fraction of a unit load, so no repeater is needed below that count.
Is the reel 3000 pieces? Yes on the DRBR row, 3000 on a large reel, moisture level 1 with unlimited floor life. The DRBT row of the same body is 250 pieces on a small reel.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.