SN65HVD72DR
Product Specifications
SN65HVD72DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65HVD72DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65HVD72DR: 250 kbps half duplex RS-485 transceiver with IEC ESD protection in the eight pin SOIC
SN65HVD72DR is a 3.3 V RS-485 driver and receiver pair intended for the slow end of the family, where cable length matters more than data rate in a SOIC body of 8 pins. It runs from a single 3.3 V supply with 5 V tolerant logic inputs, carries more than 15 kV of human body model and 12 kV of IEC contact discharge protection on the bus pins, and holds 80 mV of receiver hysteresis for noise rejection. The 250 kbps rate is a slew limited part for long cable, and the unit loading allows more than 200 nodes on one bus.
Order code and package
| SN65HVD72DR | SOIC D body, 8 pins, 2500 pieces on a large reel, Active in the addendum dated 18 September 2026, NIPDAU finish, moisture level 1 with no floor life limit, marking HVD72, minus 40 to plus 125 degrees |
| SN65HVD72D | the same SOIC body in a 75 piece tube at the same moisture level, which is the prototype and repair quantity |
| SN65HVD72DGKR | VSSOP DGK body, 8 pins, 2500 pieces on a large reel, marking HVD72, for a board where the 3 mm by 3 mm body is the difference between fitting and not |
| SN65HVD72DRBR | SON DRB body, 8 pins, 3000 pieces on a large reel, and the small reel row for the same body is 250 pieces, so both quantities exist on this body |
| SN65HVD75DR | the 20 Mbps member in the same SOIC body and the same reel, which is the string to move to when 250 kbps stops being enough and the cable is short |
Electrical parameters that decide the application
| Signalling rate | 250 kbps on this member, against 20 Mbps on the SN65HVD75 and 50 Mbps on the SN65HVD78, all in the same eight pin bodies |
| Supply | single 3.3 V rail with 5 V tolerant logic inputs, so a 5 V controller drives the driver enable and the data input directly |
| Bus protection | more than 15 kV human body model, more than 12 kV IEC 61000-4-2 contact discharge and more than 4 kV IEC 61000-4-4 fast transient burst on the bus pins |
| Receiver hysteresis | 80 mV, which is what keeps a slow or attenuated edge from producing multiple transitions at the receiver output |
| Unit loading | more than 200 nodes on one bus, against the 32 nodes of a standard one unit load transceiver |
| Quiescent current | under 2 uA in standby and under 1 mA during operation, which is what a loop powered node needs |
| Common mode range | the standard RS-485 window of minus 7 V to plus 12 V, which is what makes a multi-point bus with separate grounds workable |
| Power up and power down | glitch free bus inputs and outputs, so a node that powers up in the middle of traffic does not corrupt the bus |
| Driver output | differential output into a 54 ohm load, with the short circuit current limited so a fault does not destroy the driver |
| Temperature | minus 40 to plus 125 degrees, the extended industrial range rather than the 85 degree one |
Family variants and how they differ
| The three rate members | 72 at 250 kbps, 75 at 20 Mbps and 78 at 50 Mbps, all in SOIC, VSSOP and VSON bodies with the same pinout, so the rate is a part number change rather than a board change |
| SN65HVD72 against SN65HVD3082E | the 3082E is the older 200 kbps part with a lower ESD rating, and the 72 is the drop in with the IEC contact discharge protection |
| SN65HVD72 against an isolated transceiver | an isolated part such as the ISO1450 adds a barrier and removes the ground difference problem, at several times the price, and the choice is made by whether the nodes share a ground |
| Against the SN65HVD230 CAN part | CAN and RS-485 use different framing and different arbitration, so the two are not substitutes even though both are differential bus transceivers in eight pin bodies |
| Body options | the D, DGK and DRB bodies are the same silicon, so the choice is footprint and reel size |
Points to check before this part goes on a BOM
The 250 kbps rate is a deliberate slew limit rather than a process limit. A slower edge radiates less and survives more cable, which is why the part exists alongside the 20 and 50 Mbps members. A link that needs 1 Mbps cannot use this part and cannot fix the problem with a shorter cable; the SN65HVD75 is the correct move and it shares the pinout.
The 80 mV of hysteresis is the number that decides whether a bus with 200 nodes and long stubs works. Reflections at the end of a stub arrive as a small oscillation around the threshold, and a receiver with 20 mV of hysteresis turns that into multiple transitions while one with 80 mV ignores it. This is the reason the part is used on multi-drop buses where the topology is not clean.
The 200 node figure comes from the unit loading rather than from a driver strength claim. A standard RS-485 receiver presents one unit load, and this part presents a fraction of that, so the same driver can feed six times as many receivers. On a bus with more than 32 nodes this is the specification that makes the bus legal rather than the driver current.
The 12 kV of IEC contact discharge is a system level claim only when the bus pins are brought out to a connector with a short return path. A long trace from the connector to the part adds inductance and turns the same 8 kV into a failure. The datasheet application section shows the arrangement with a transient suppressor and a series resistor, and the ESD rating assumes it.
The 3.3 V supply with 5 V tolerant logic is what allows a mixed logic board to use this part without level shifters. The 5 V tolerance applies to the logic pins and not to the bus pins, and a bus pin driven to 5 V by a fault is outside the common mode window and will clamp through the internal diodes. That distinction matters when a 5 V node and a 3.3 V node share a bus.
Under 2 uA in standby is the figure that makes a battery or loop powered node possible. The receiver keeps its input impedance in standby, so a sleeping node does not load the bus, and it wakes on the next transition. A part without that behaviour draws milliamps continuously and drains a loop powered node's budget before the measurement is taken.
Choosing between the three rate members
The rate is set by the cable and the node count, not by the microcontroller. A 250 kbps part over 1000 m of twisted pair works because the edge is slow enough that the reflections settle before the sample point; a 20 Mbps part over the same cable fails regardless of the transceiver. Moving to the faster member is a decision about cable length, and the pinout compatibility makes the decision reversible.
The faster members in the same family carry the same ESD and hysteresis specifications, so the trade is only speed against cable. That is unusual in a transceiver family and it is why the three strings appear together in one document with one electrical table per rate.
Grounding a multi-point bus
The minus 7 V to plus 12 V common mode window is what allows a bus to run between cabinets on separate grounds, and the 200 node figure assumes those grounds are within the window. A lightning strike or a fault that lifts a ground beyond 12 V puts the transceiver outside its rating, and the transceiver is then the fuse. An isolated part or a ground clamp is the answer, and the transceiver rating is not.
Where this order code fits
Factory automation, telecom infrastructure, motion control and building buses are the applications the vendor names, and each of them runs a multi-drop bus over tens or hundreds of metres where the edge rate and the noise margin matter more than the data rate. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Can it run at 1 Mbps? No. This member is the 250 kbps one, and the 20 Mbps SN65HVD75 is the string to order for a faster bus in the same footprint.
How many nodes can share the bus? More than 200, because the receiver presents a fraction of a unit load rather than a full one.
Does it need a 5 V supply for 5 V logic? No. The logic inputs are 5 V tolerant while the part runs from 3.3 V, so a 5 V controller connects directly.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.