Contact Us

SN65HVD485EP

Brand: Texas Instruments
Texas Instruments SN65HVD485EP is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD485EP — Power Management & Signal Chain | Superb Automation

SN65HVD485EP

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD485EP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD485EP: a 5 V half duplex RS-485 transceiver in a DIP body

The SN65HVD485EP is a 5 V half duplex RS-485 transceiver that carries up to 10 Mbps, connects 64 nodes at a 1/2 unit load, and sits in a P DIP 8 body, which is the through hole package that legacy boards and small volume builds still use. It meets TIA/EIA-485A and matches the industry standard SN75176 footprint, so an existing land pattern takes it without change.

The current profile is modest: less than 2 mA typical in the active state, and below 1 mA in shutdown. The bus pins are protected to 15 kV human body model, the receiver is fail safe on a bus that is open, shorted or idle, and power on reset keeps the outputs high impedance until the supply has settled. The part is characterised from minus 40 C to 85 C.

Key data for the SN65HVD485EP

RateUp to 10 Mbps over twisted pair, the fast member of the family it belongs to
Loading1/2 unit load, up to 64 nodes on one bus segment
CurrentLess than 2 mA typical active, below 1 mA in shutdown, both exclusive of the bus load
ProtectionBus pin ESD up to 15 kV HBM, thermal shutdown, glitch free power up and down
ReceiverBus open fail safe, so an idle or disconnected pair reads as a defined level rather than noise
SupplySingle 5 V rail, matched to the SN75176 logic thresholds that older controllers expect

Body, marking and reel data

BodyP, DIP 8, the through hole body that suits socketed and hand assembled boards
Packaging50 pieces in a tube, not a reel, so a pick and place line needs a tube feeder
Family bodiesThe same silicon is published in a DGK VSSOP 8 and a D SOIC 8 for reel placement
HandlingDIP bodies are not moisture sensitive in the usual sense, but the tube is open at both ends and needs a dry store
TemperatureMinus 40 C to 85 C operating range, the industrial band rather than a commercial one

Why the DIP body still matters

Most of the RS-485 traffic in new builds goes into a surface mount package, and the DIP part looks like a leftover. It is not, in three situations. Service spares for equipment installed fifteen years ago are often ordered as DIP because the board has a socket or because the repair is done by hand in the field. Low volume builds of a few hundred boards sometimes cannot justify a stencil and a reflow profile. Test fixtures and evaluation boards are assembled and modified by hand.

The 10 Mbps rate is the other reason the part is chosen. Half duplex RS-485 at 10 Mbps over a short pair is a common way to move a block of data between two boards inside one enclosure without a parallel bus, and the 5 V rail matches the logic that older microcontrollers use. The 1/2 unit load limit of 64 nodes is well above what an in-cabinet link needs. Two protection details are worth naming for a service part. The thermal shutdown holds the driver off rather than letting it cook when a fault pins the pair, and the current limit works in both directions so a negative fault is handled like a positive one. A board that comes back from the field with a dead transceiver usually saw one of those two events and had no series resistor in front of the connector.

Questions we get when this code is on a BOM

The first question is about packaging. A customer who expects a reel and receives a tube of 50 will stop the line, so we say on the offer that the EP row ships in tubes and that the DGK or D rows are the reel alternatives. Changing the body is a board change, which is a different decision from changing the packaging.

The second question is whether a 3.3 V controller can drive this part directly. The logic thresholds of a 5 V transceiver are not guaranteed at 3.3 V, so the answer is a level shifter or a 3.3 V transceiver. We check the controller rail before quoting, and where the answer is a 3.3 V part we quote the low power family instead.

How SUPERB supports this line item

We keep the SN65HVD485EP for service and low volume builds, and we state the tube quantity on the offer so a production planner is not surprised. Customers who want the same silicon on a reel can move to the DGK or D body, and our pin to pin cross reference page shows how we compare the three bodies of this family.

For spares and repair kits, the kitting service lets a service organisation receive the transceiver, the connector and the termination parts counted per kit, which removes a stockroom step from every repair.