SN65HVD30MDREP
Product Specifications
SN65HVD30MDREP
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65HVD30MDREP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65HVD30MDREP: enhanced product grade of the 26 Mbps 3.3 V full duplex RS-485 transceiver, with the driver permanently enabled
SN65HVD30MDREP is a differential driver and receiver with separate pins for each direction, no enable pins, built for 26 Mbps and for 64 nodes on one bus in a SOIC body of 8 pins. It runs from a 3.3 V supply, carries 26 Mbps over cable runs up to 1500 m at the slow end of the family, presents one half of a unit load so 64 nodes fit on one bus, and carries separate driver and receiver pin pairs with no enable pins at all. The differential output is 1.5 V minimum into 54 ohm, the driver propagation is 29 ns typical, pulse skew is held to 5 ns, the bus pins survive 15 kV human body model, and the part is characterised from minus 40 to plus 85 degrees.
Order code and package
| SN65HVD30MDREP | the string in this catalogue entry carries an M and a REP, which is the enhanced product grade of this device. The document this page was written from prints the industrial rows only and points to a separate SN65HVD30-EP document for the enhanced grade, so the reel size, the grade and the marking for this exact string have to be read from that file or from the reel label |
| SN65HVD30DR | SOIC D body, 8 pins, 2500 pieces on a large reel, Active in the addendum dated 10 August 2026, marking VP30, minus 40 to plus 85 degrees, which is the industrial row a plain order would name |
| SN65HVD30D | the 75 piece tube industrial row, printed Obsolete in the current addendum, so a bill of materials that still names the tube has no orderable path in that grade |
| SN65HVD30DR.A and DRG4 | the lead free declaration rows of the same 2500 piece reel, printed with a NIPDAU finish and moisture level 1, which is the string a material declaration has to name |
| SN65HVD31 and SN65HVD32 | the other two fully enabled members: 5 Mbps and 1 Mbps with one eighth of a unit load and 256 nodes, so the three strings are the same function at three rates and two load classes |
| SN65HVD33 and SN65HVD35 | the same rates with an active high driver enable and an active low receiver enable, which is the row to quote when a node has to be silenced |
Electrical parameters that decide the application
| Signalling rate | 26 Mbps on this member, against 5 Mbps on the 31 and 1 Mbps on the 32, and the same 26 Mbps on the 33 which adds enables |
| Unit load | one half of a unit load, which is 64 nodes on one bus, against 256 nodes on the one eighth load members. The faster the driver, the heavier the input, and the node count follows |
| Duplex | full duplex, so the driver pair and the receiver pair are separate pins and the two directions run at the same time on four wires |
| Driver differential output | 1.5 V minimum into a 54 ohm load per RS-485 and 2 V minimum into 100 ohm per RS-422, with the change between states held inside 0.2 V |
| Common mode output | 1.6 V to 2.3 V steady state, with a peak to peak of 0.5 V on this member and the 33, which is larger than the 0.25 V on the slower members and is the price of the faster edge |
| Receiver thresholds | a positive threshold at minus 0.02 V maximum and a negative threshold at minus 0.20 V minimum, with 50 mV of hysteresis between them |
| Driver propagation | 29 ns typical and 70 ns maximum, with a pulse skew of 5 ns, which is what 26 Mbps needs and what keeps the duty cycle of a returned clock close to fifty per cent |
| Short circuit current | limited to 250 mA on the output, with the datasheet noting that a short to a negative voltage can exceed that limit and that continuous exposure affects reliability |
| ESD | more than 15 kV human body model on the bus pins, measured to the JEDEC specification |
| Enable pins | none on this member. The driver and the receiver are on whenever the supply is, which is the property that decides the topology |
| Failsafe | a defined output on an idle bus, an open circuit and a shorted pair |
| Temperature | minus 40 to plus 85 degrees, which is the narrower of the two ranges in this family and the one to check against a hot enclosure |
Family variants and how they differ
| 30 against 33 | same rate, same body size, the 33 adds enables and a standby current below 1 uA. A point to point link saves two control lines with the 30 and a shared bus needs the 33 |
| 30 against 31 | 26 Mbps against 5 Mbps, 64 nodes against 256. The faster part is the one for a short cabinet link, the slower one for a long field run |
| Against the HVD1477 family | 50 Mbps, 30 kV of protection and 125 degrees, at a higher price. A link with margin at 26 Mbps stays on this part |
| Against the HVD1794 | 70 V fault protection and a cable invert pin at 115 kbps. That part is for a bus that can meet a supply rail, this one is for a clean cabinet link |
| Against a 5 V full duplex part | the same function on a 5 V rail, which needs a level shifter for a 3.3 V controller. This family removes the shifter and keeps the bus levels |
Points to check before this part goes on a BOM
The half unit load is the number that separates this member from its slower siblings. Sixty four nodes on one bus instead of 256, because each receiver presents twice the load. A customer replacing a 1 Mbps member with this one to gain speed and keeping the same node count has a bus that will not hold its differential amplitude at the far end.
With no enable pins the driver is always on, which makes this a point to point or a star link part. A shared two wire bus with a permanently enabled driver is a contention fault that no firmware can avoid, because the pin does not exist. The 33 is the same silicon with the enables brought out, and that is the substitution to quote when a customer's topology is a shared bus.
The 26 Mbps rate and the 1500 m cable figure appear in the same document and they belong to different members. The cable length figure is the family statement and the rate is per member; a 1500 m run at 26 Mbps is not a link, it is a hope. The rate table and the cable table have to be read together, and the slowest member is the one that reaches the far end of the cable.
Pulse skew of 5 ns is the figure that matters when a recovered clock comes back over the bus. At a 38 ns bit time, 5 ns of skew is thirteen per cent of a bit, which is inside a UART's tolerance and outside the tolerance of a link that expects a clean eye. The faster members of the family hold a tighter skew and cost more, and a customer clocking data from a transceiver output is the one who needs to know the difference.
The obsolete tube row is a live procurement problem rather than a historical note. A customer with a tube part number in a bill of materials that has not been revised since the part was released will find no orderable path, and the answer is the reel with a re reeling cost or a move to the .A row. Saying that at the quoting stage is cheaper than discovering it at the purchase order.
The M and REP in this catalogue string are the enhanced product grade, and that grade is published with its own document and its own qualification. The features section of this file names SN65HVD30-EP as the enhanced member for defense, aerospace and medical applications, and it prints the industrial rows in the addendum. An offer that quotes the industrial reel for an enhanced grade order is quoting a part the customer did not ask for, which is the substitution that surfaces at an incoming inspection rather than at the order.
The short circuit limit of 250 mA comes with a caveat for shorts to a negative voltage, where the current can exceed the limit and continuous exposure affects reliability. That is the honest sentence to put in front of a customer whose bus can be shorted during service: the part survives short events, and a bus that can be shorted indefinitely needs series protection rather than a reliance on the transceiver's limit.
Why a full duplex part at 26 Mbps exists
Encoders, resolvers and motion controllers stream position data one way and commands the other at the same time, and a two wire link would spend a large share of the bit time turning around. Four wires remove the turnaround and let both directions run at the full rate, which is why this family appears in machine tools and in robotics rather than in building networks.
The price of the arrangement is a permanently enabled driver at one end, which is why the parts with enables exist in the same document. A board team choosing between the 30 and the 33 is choosing a topology, not a feature.
Reading the order code
SN65HVD30 reads as the family, HVD for the transceiver and 30 for the first of the six member table, which is the 26 Mbps fully enabled row. The D at the end is the SOIC body and the R is a 2500 piece large reel. The rate is in the number and not in a suffix, and the string carries no temperature code because the family has one range per member.
Where this order code fits
Utility meters, DTE and DCE interfaces, industrial and building automation and point of sale networks are the stated applications, and the ones that use this member are the short cabinet links rather than the long field runs. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the CAN Bus Transceiver Selection page.
Questions buyers ask
Can this part be silenced on a shared bus? No. It has no enable pins, so the driver is on while the supply is. The 33 is the same rate with enables.
How many nodes does it allow? 64, from the half unit load. The slower members of the same family allow 256.
Is the tube still available? No. SN65HVD30D is printed Obsolete, so only the 2500 piece reel rows are live.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.