Contact Us

SN65HVD230QDR

Brand: Texas Instruments
Texas Instruments SN65HVD230QDR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD230QDR — Power Management & Signal Chain | Superb Automation

SN65HVD230QDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD230QDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD230QDR: 3.3 V CAN transceiver with a standby mode that drops the bus to 370 uA

SN65HVD230QDR is an ISO 11898-2 physical layer transceiver for a 3.3 V controller, with slope control on the driver, a split reference output and a standby mode on the 230 member in a SOIC body of 8 pins. It runs from a 3 V to 3.6 V supply, carries data at up to 1 Mbps, allows 120 nodes on one bus, survives 16 kV human body model on the bus pins and holds a defined recessive level on an open circuit. The 230 member adds a standby mode that draws 370 uA typical, the 231 member goes further into a sleep mode at 40 nA typical, and the RS pin sets either the slew rate of the driver through a resistor or the low power state through a logic level.

Order code and package

SN65HVD230QDRthe string in this catalogue entry carries a Q after the base number. The addendum inside SLOS346O prints the industrial rows only, SN65HVD230D, SN65HVD230DR, DR.A and DRG4, so the Q row is not described by this document and its reel, grade and marking have to be confirmed from the vendor or from the reel label
SN65HVD230DRSOIC D body, 8 pins, 2500 pieces on a large reel, Active, minus 40 to plus 85 degrees, marking VP230, and the row a plain industrial order should name
SN65HVD230DR.Athe same reel and the same body with a NIPDAU finish printed on the row, moisture level 1 with no floor life limit, which is the string to quote when the customer asks for the lead free variant by name
SN65HVD230Dthe 75 piece tube row, printed Obsolete in the current addendum. A bill of materials that still names the tube has no orderable path and every quote against it should say so
SN65HVD231 and SN65HVD232the other two members in the same body: the 231 replaces standby with a sleep mode at 40 nA and the 232 has neither standby nor sleep, so the three strings are three different power strategies on the same pinout

Electrical parameters that decide the application

Supply3 V to 3.6 V, which is the 3.3 V logic rail directly and the reason this part exists next to the 5 V CAN transceivers
Data rateup to 1 Mbps, the high speed CAN physical layer rate, with the loop timing set by the transceiver rather than by an external component
Nodesup to 120 on one bus, which is the figure the high input impedance of the receiver allows and the number to quote against a multi drop harness
Standardcompatible with ISO 11898-2, so the differential levels, the recessive bias and the dominant drive follow the standard rather than a vendor variation
Standby current370 uA typical and 600 uA maximum on the 230 member with the RS pin high, which is the mode a parked vehicle uses to keep the bus monitored without flattening the battery
Sleep current40 nA typical and 1 uA maximum on the 231 member, which is two orders of magnitude below the standby figure and needs a wake path back into the controller
Propagation70 ns typical and 125 ns maximum, the loop delay that sets the usable bus length at 1 Mbps
ESDmore than 16 kV human body model on the bus pins, which is the level a service technician produces on a dry day and the number fleet maintenance asks about
Slope controla resistor from the RS pin to ground sets the driver transition time, which trades edge rate against radiated emissions, and a direct logic low on that pin selects the fast mode
Reference outputthe VREF pin on the 230 and 231 holds half the supply for a split termination, which is one resistor pair per node removed from the bill of materials
Protectionthermal shutdown and an open circuit fail safe receiver, so a shorted bus or an unplugged connector does not leave the controller reading noise
Temperatureminus 40 to plus 85 degrees on the printed rows of this document, which is narrower than the 125 degree range the RS-485 families carry

Family variants and how they differ

230 against 231standby at 370 uA against sleep at 40 nA. Standby keeps the receiver alive and wakes on bus activity, sleep turns more of the device off and needs the controller to bring it back, so the choice follows the wake strategy rather than the current figure
230 against 232the 232 has no low power mode and no VREF pin, which makes it the cheapest member and the wrong one for a module that has to sit on a sleeping bus
Against a 5 V transceivera 5 V part such as the SN65HVD255 needs a level shift to a 3.3 V controller. This family removes the shifter and keeps the same bus levels, which is why a 3.3 V microcontroller board starts here
Against an isolated transceiveran ISO1050 class part puts a barrier in the package for a bus that crosses a ground boundary. The 230 family has no barrier and costs a fraction of the isolated part, so the decision is a system one about grounds
Against a CAN FD parta CAN FD transceiver carries the faster data phase at 2 Mbps and beyond. This family stops at 1 Mbps, so a controller with a CAN FD peripheral still needs a 1 Mbps transceiver if the network is classic CAN

Points to check before this part goes on a BOM

The Q in this catalogue string is the one thing on the page that cannot be confirmed from the document. Every other row of the family is printed, and none of them carries a Q. That letter usually marks an automotive qualified part, and an automotive part is published with its own qualification document, so the reel size, the moisture level and the marking for this string have to be read from that file. An offer that assumes the industrial row's 2500 piece reel without saying so is a substitution the customer has not agreed to.

The standby current of 370 uA is quoted with the RS pin high and the driver off, and it is the receiver that stays alive. On a vehicle that sits for a month, 370 uA is 0.27 Ah, which is a real fraction of a small battery. The 231 member at 40 nA is 0.03 mAh over the same month, and the difference is why the two members exist side by side in the same body.

The loop delay of 125 ns at the maximum is what limits the bus length at 1 Mbps. The signal has to travel to the far node and the acknowledgement has to come back inside the arbitration window, and the transceiver delay is part of that budget twice. A 40 m bus at 1 Mbps is comfortable and a 200 m bus at 1 Mbps is not, whatever the cable specification says.

Slope control is where most emissions problems are solved or created. A resistor from the RS pin to ground slows the driver edges, which reduces the high frequency content that a harness radiates. Too much resistance and the bit time is eaten at the receiver, which shows up as errors at long cable lengths. The datasheet gives the relation between the resistor and the transition time, and a value chosen by experiment on one harness does not transfer to another.

The VREF pin is a convenience that has to be used with care. It holds half the supply for a split termination, and it can only source or sink a small current. A node that uses it to bias a long stub, or that ties two nodes' VREF pins together, loads the reference and shifts the recessive level for every node on the bus. The datasheet limits the pin current and that limit is the one to quote.

Thermal shutdown protects the driver from a bus shorted to a supply for a long time, and it is a latch that recovers when the fault clears. What it does not protect is the controller: a bus shorted to 12 V puts a fault on the CAN pins of the microcontroller through the digital side of the transceiver, and the isolation between the two is a rating to check rather than assume.

Why 3.3 V CAN is its own family

A 3.3 V microcontroller with a 5 V transceiver needs either a level shifter on the TX and RX lines or a controller with 5 V tolerant pins. Both cost board area and both add a failure mode. The 3.3 V transceiver removes the shifter and keeps the bus levels at the standard differential values, which is why a 3.3 V board starts with this family and not with a level shifted 5 V part.

The differential bus levels do not depend on the supply, so a 3.3 V node and a 5 V node can share a bus. What they cannot share is a termination strategy that assumes a particular recessive common mode, because the two families bias the bus slightly differently. A mixed bus is legal and worth mentioning in a quote for a retrofit.

Reading the order code

SN65HVD230 breaks down as the family, HVD for the high speed CAN transceiver and 230 for the member with standby. The D at the end is the SOIC body and the R is a large reel. The 231 and 232 are different numbers rather than suffixes, and the Q in this catalogue string sits where a qualification letter normally sits, which is exactly why it has to be confirmed rather than inferred.

Where this order code fits

Industrial automation, motor and robotic control, building and climate control, telecom and basestation status links, and the CANopen, DeviceNet and CAN Kingdom stacks are the applications the vendor names. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is the Q string described by this document? No. The addendum prints the industrial rows only, so the reel, the grade and the marking for SN65HVD230QDR have to be confirmed from the vendor or from the reel label.

Can it share a bus with 5 V transceivers? Yes. The differential levels are set by the standard rather than by the supply, so a mixed bus works, with the caveat that the recessive bias differs slightly between families.

Is the tube row still orderable? No. SN65HVD230D is printed Obsolete in the current addendum, and only the reel rows are Active.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.