Contact Us

SN65DPHY440SSRHRR

Brand: Texas Instruments
Texas Instruments SN65DPHY440SSRHRR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65DPHY440SSRHRR — Power Management & Signal Chain | Superb Automation

SN65DPHY440SSRHRR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65DPHY440SSRHRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65DPHY440SSRHRR: MIPI D-PHY retimer that restores up to four lanes at 1.5 Gbps through a cable or a long board run

SN65DPHY440SSRHRR is a one to four lane retimer for MIPI CSI-2 and DSI links, with a configurable input equaliser, a selectable output pre-emphasis and automatic skew correction between the clock and the data lanes in a WQFN body of 28 pins. It runs from a single 1.8 V supply between 1.62 V and 1.98 V, carries up to four data lanes and a clock at 1.5 Gbps per lane with clock rates from 100 MHz to 750 MHz, and draws 150 mW with four lanes active at 1 Gbps, falling to 14 mW in the LP11 state and 0.75 mW with the reset asserted. The device is compliant to the MIPI D-PHY 1.1 specification, supports the low power and ultra low power states including bidirectional DSI low power mode, and the industrial member is characterised from minus 40 to plus 85 degrees.

Order code and package

SN65DPHY440SSRHRRWQFN RHR body, 28 pins, 3000 pieces on a large reel, Active in the addendum dated 10 August 2026, NIPDAU finish, moisture level 1 with no floor life limit, marking DPHY440, minus 40 to plus 85 degrees
SN65DPHY440SSRHRTthe same body on a 250 piece small reel, and the addendum prints that row with a 0 to 70 degree range while the same document characterises the SN65 device from minus 40 to plus 85. The row print is inconsistent with the device section and the reel label is the only reliable source
SN75DPHY440SSthe commercial member, 0 to 70 degrees, same die and same package, which is the row to quote for a consumer product where the ambient never goes below freezing
SN65DPHY440SSRHRRG4the lead free declaration row of the same 3000 piece reel, printed with the same NIPDAU finish, which is the string a material declaration has to name
The RHRT small reel250 pieces is a prototype and repair quantity. A production build that quotes the small reel row discovers a four to eight week lead time where the large reel was in stock, because the two rows are stocked separately

Electrical parameters that decide the application

Lanes and rateone to four data lanes plus a clock, 1.5 Gbps per lane, with the clock between 100 MHz and 750 MHz, which covers the camera and display links used in tablets, notebooks and industrial cameras
ComplianceMIPI D-PHY 1.1, in either a CSI-2 or a DSI application, so the same part serves a camera input and a display output as long as the lane count and the rate fit
Supply1.62 V to 1.98 V on a single rail, 1.8 V nominal, and the input pins tolerate the MIPI low power levels without a separate 1.2 V rail on the control side
Power150 mW with four lanes at 1 Gbps, 115 mW with two lanes, 14 mW in the LP11 state with the supplies stable, and 0.75 mW with the reset asserted, which is the set of numbers that decides whether the part can stay powered in a phone that sleeps
Equalisationan adjustable input equaliser on every lane, which is the function that recovers a signal after a cable and a connector have removed the high frequency content
Output controlselectable pre-emphasis levels, a configurable output edge rate and an adjustable output swing set by the VSADJ_CFG0 pin, so the same part drives a short board trace and a flex cable
Skew correctionthe output pins compensate for uneven skew between the clock lane and the data lanes received at the input, which is the failure mode that a flexible cable produces when its lanes are not equal length
Low power statesboth ULPS and LP states are supported, with activity detection on the link interface that moves the device into a lower power state when the link goes idle
ESD3 kV human body model, which is modest for a connector facing part and is the number to quote when a customer asks about handling rather than about cable discharge
Temperatureminus 40 to plus 85 degrees on the SN65 member and 0 to 70 on the SN75 member, with the reel row print inconsistency noted above
Body size5.5 mm by 3.5 mm in a 28 pin WQFN, which is the number that matters on a camera board where the retimer sits between two connectors
Bidirectional low powerDSI low power mode is supported in both directions, so a display link that needs to read back from the panel works through the part

Family variants and how they differ

SN65 against SN75same die, same package, same electrical table, different temperature grade. The 65 is the industrial part and the 75 is the commercial part, and the price difference is small enough that most buyers take the industrial row
Against a redrivera redriver restores amplitude and does not regenerate the protocol timing. A retimer re times the link, which is what a marginal cable needs, and it also costs more and consumes more
Against a bridgea CSI-2 bridge changes the interface, for example from CSI-2 to parallel. This part does not change the interface, it restores it, so the two are not alternatives
Against a longer flex cablethe cheaper answer to a marginal link is a shorter or a better cable. When the mechanical envelope does not allow that, the retimer is the only option that keeps the same connector and the same sensor
Against two retimersa link with two retimers in series is a link with two sets of equaliser settings that interact. One retimer placed at the worst point of the channel is the normal answer

Points to check before this part goes on a BOM

The lane count and the rate are separate limits and both have to fit. Four lanes at 1.5 Gbps is the headline, and a two lane link at 1.5 Gbps is also inside the part, but a four lane link at 2.5 Gbps is not, whatever the lane count says. A camera that needs 2.5 Gbps per lane is a different device and there is no setting on this one that reaches it.

The 1.8 V single supply is the reason this part fits a camera board. It does not need a 1.2 V rail for the low power signalling, and the control pins accept the levels the link already carries. A board that has a 1.2 V rail for other reasons and no 1.8 V rail is the case where the part does not fit, and that is an architecture question rather than a substitution question.

The equaliser and the pre-emphasis are two ends of the same problem and they should not both be turned up. An input equaliser set too high amplifies noise along with the signal, and a pre-emphasis set too high adds energy to the edges that the far end then has to absorb. The vendor's tuning procedure moves one at a time and watches the eye at the receiver, and a board that is set by copying a reference configuration usually has one of the two wrong.

The skew compensation inside the part covers the difference between lanes that the cable introduces. It does not cover a difference in trace length on the board between the connector and the part, and it does not cover a lane order mistake. A lane swap on a four lane link is a board arrangement error that no retimer setting corrects, and it is the most common bring up failure on this class of part.

The power numbers are quoted at 1 Gbps and they move with the rate and with the settings. 150 mW at four lanes is the number for a mild equaliser and a mild pre-emphasis; turning both up adds tens of milliwatts. A phone with a 3.8 V battery and a 150 mW part spends 40 mA on the retimer, which is why the LP11 and reset states matter as much as the active figure.

The temperature row print is worth flagging to the customer rather than resolving silently. The device section of the document characterises the SN65 member from minus 40 to plus 85, and the addendum prints 0 to 70 on the small reel row of the same string. Either the row print is a column shift or the small reel is a different grade; the reel label and the vendor confirmation settle it, and an offer that quotes minus 40 to plus 85 against a part whose label says 0 to 70 is a claim the customer can disprove.

What a retimer does that a redriver does not

A redriver is an analogue amplifier with a fixed or a switchable equaliser. It makes the eye taller and wider and passes whatever timing it was given. A retimer recovers the clock from the data, re times the transitions and drives a new eye, which is why it also corrects the lane to lane skew and the duty cycle distortion that a long cable introduces.

The cost of that function is power and latency. This part adds a small but finite delay per link and draws 150 mW at four lanes, against a redriver that draws less and adds almost nothing. A link that is marginal because of amplitude wants the cheaper device; a link that is marginal because the eye is closed in time wants this one.

Reading the order code

SN65DPHY440SS reads as the family, DPHY440 for the function and SS for the silicon revision, and the RHR at the end is the 28 pin WQFN body. The R suffix is a large reel of 3000, the T suffix is a small reel of 250, and the G4 row is the lead free declaration. The 65 against 75 at the front is the temperature grade. Nothing in the string selects the lane count, because the part covers one to four lanes in every row.

Where this order code fits

Notebook PCs, clamshell and convertible machines, tablets and cameras are the stated applications, and the industrial version reaches machine vision heads and medical camera arms where the same flex cable problem appears with a longer life requirement. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Does it support 2.5 Gbps per lane? No. The limit is 1.5 Gbps per lane at a clock of up to 750 MHz, which is the D-PHY 1.1 ceiling this part is built to.

Can it fix a lane swap? No. The part corrects skew between lanes, not the order of the lanes. A swapped pair is a board arrangement error that has to be corrected in copper.

Is the small reel a different temperature grade? The addendum prints 0 to 70 on that row while the device section says minus 40 to plus 85 for the SN65 member. The reel label settles it, and the row print should be confirmed with the vendor before a wide temperature claim is made.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.