Contact Us

SN65C3243DBR

Brand: Texas Instruments
Texas Instruments SN65C3243DBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65C3243DBR — Power Management & Signal Chain | Superb Automation

SN65C3243DBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65C3243DBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65C3243DBR: three driver and five receiver RS-232 interface in the twenty eight pin SSOP with an always active ring indicator output

SN65C3243DBR is a complete RS-232 port on one chip, with the charge pump and the receivers that a serial connector needs in a SSOP body of 28 pins. It provides three line drivers and five line receivers with a dual charge pump that runs from a single 3 V to 5.5 V supply using four 0.1 uF capacitors, reaches 1 Mbit/s with a slew rate between 24 and 150 V per microsecond, and draws 1 uA in standby. The ROUT2B output stays active while the device is powered down, which is what allows a ring indicator to wake the host.

Order code and package

SN65C3243DBRSSOP DB body, 28 pins, 2000 pieces on a large reel in the addendum dated 12 February 2026, NIPDAU finish, moisture level 1 with no floor life limit, marking 65C3243, minus 40 to plus 85 degrees
SN65C3243DBR reel sizethe same page prints two different reel quantities for this string: the addendum prints 2000 pieces on a large reel and the package materials table prints 1000 in its quantity column, so the reel size has to be named on the purchase order rather than assumed
SN65C3243DWSOIC DW body, 28 pins, 20 pieces in a tube at the same moisture level, which is the through hole style body for a repair or a hand assembled prototype
SN65C3243DWRthe same DW body on a large reel, printed at 1000 pieces in the addendum against 2000 in the materials table, the same disagreement as the SSOP row
SN65C3243PWRTSSOP PW body, 28 pins, 2000 pieces on a large reel, and the addendum prints this body at 0 to plus 70 degrees rather than the minus 40 to plus 85 of the SSOP and SOIC rows

Electrical parameters that decide the application

Drivers and receiversthree line drivers and five line receivers, which is a full nine pin serial port including the ring indicator and the two handshake lines
Supply3 V to 5.5 V single rail, with the charge pump generating the positive and negative RS-232 levels from four 0.1 uF capacitors
Data rate250 kbit/s to 1 Mbit/s, with a slew rate between 24 and 150 V per microsecond that keeps the edges inside the RS-232 standard at both rates
Standby current1 uA typical, which is what a battery powered terminal needs between transmissions
Logic compatibilityaccepts 5 V logic inputs while running from a 3.3 V supply, so a 5 V controller connects without a shifter
Bus pin protectionplus or minus 15 kV human body model on the serial port pins including ground, which is the connector level rating rather than a chip level one
Always active outputROUT2B stays valid with the device powered down or in force off, so a modem can assert ring indicator against a sleeping host
Charge pumpdoubles and inverts the supply with the four external capacitors, and the capacitor values are fixed at 0.1 uF rather than scaled with the supply
Interoperabilitybuilt to interoperate with the SN65C3238 and SN75C3238, so a board that carries the older part can take this one on the same footprint
Temperatureminus 40 to plus 85 degrees on the SSOP and SOIC rows, but 0 to plus 70 degrees on the TSSOP row

Family variants and how they differ

DB against DW and PWthe SSOP, SOIC and TSSOP bodies carry the same silicon, but the PW row is printed at 0 to plus 70 degrees while the other two are minus 40 to plus 85, so a TSSOP substitution can narrow the operating range without changing the function
SN65C3243 against SN65C3238the 3238 is the five driver and three receiver arrangement, and the two interoperate at the protocol level while the pin functions differ, so a board laid out for one does not take the other
Against a single driver parta one driver and one receiver part such as the MAX3221 class saves pins and loses the handshake lines, so the port count decides the family
SN65C3243 against SN75C3243the 75 prefix is the same function on a different process, and its SOIC body is the DW with a wider temperature print, so the two are read from the same table
Against an isolated RS-232 partan isolated transceiver adds a barrier for a port that leaves the enclosure, at several times the price, and the choice is made by whether the connector is accessible to the user

Points to check before this part goes on a BOM

The reel size is printed twice on this page and the two numbers disagree. The addendum says 2000 for the SSOP and the materials table says 1000 for the same string, and the SOIC row disagrees the other way. That is a documentation fault rather than a part change, and the practical consequence is that a purchase order has to name the quantity and the carrier rather than relying on the suffix to imply a reel.

The TSSOP row is rated 0 to plus 70 degrees while the SSOP and SOIC rows are minus 40 to plus 85. A substitution from DB to PW for footprint reasons therefore narrows the temperature range by 40 degrees at the cold end without any change in the part number prefix. An industrial terminal that runs at minus 20 degrees will fail on the PW body and pass on the DB body.

The always active ROUT2B output is the feature that distinguishes this part from a plain three and five transceiver. It remains valid while the device is powered down, so a modem can assert ring indicator against a host that is asleep and wake it through an interrupt. A part without that output leaves the host with no way to detect an incoming call while powered down, which is a system level difference rather than a pin difference.

The 1 Mbit/s rate is above the 20 kbit/s that the RS-232 standard specifies, and the slew rate window of 24 to 150 V per microsecond is what makes both work. At the fast end the edges are still inside the standard's limit, and at the slow end a long cable is driven without ringing. A board that pushes the rate higher than 1 Mbit/s leaves the standard and the cable behaviour becomes the limiting factor.

The four 0.1 uF capacitors are not optional and cannot be scaled down. The charge pump needs them to hold the positive and negative rails under load, and a board that substitutes 1 uF for a smaller one sees the rails sag on a long cable and the receiver thresholds move. The datasheet asks for them to be ceramic and close to the pins, and that is a board arrangement requirement rather than a suggestion.

The minus 40 to plus 85 range on the SSOP body is the industrial range and not the automotive one. A serial port in an outdoor cabinet at 70 degrees ambient is inside the range at the top but the junction rise under continuous transmission can push past 85, and the part has no thermal shutdown. That is a thermal budget question rather than a part rating question, and the answer is usually airflow rather than a different transceiver.

What five receivers buy on a nine pin port

A nine pin serial port carries two data lines, six handshake lines and a ground. Three drivers and five receivers covers the two transmit paths and the handshakes in one direction, and the fifth receiver is there for the ring indicator. A part with fewer receivers leaves a handshake line unconnected, which shows up as a terminal that works with one host and hangs with another.

The always active output is mapped to the ring indicator receiver rather than to a data line because that is the only signal that has to work with the host asleep. Reading the pin table before choosing the part is what keeps that function on the right pin, since the naming between the 3238 and the 3243 arrangements differs even though the two interoperate.

Reading the two tables on this page

The addendum is generated from the vendor's orderable database and the materials table is generated from the packaging database, and on this page they disagree by a factor of two on the reel quantity for the SSOP and SOIC rows. Neither is a part change. The safe reading is that both quantities exist as reel options and that the order has to state which one is wanted, which is also the practice that keeps a production line from receiving a 1000 piece reel when the feeder was set for 2000.

Where this order code fits

Battery powered systems, notebooks, hand held terminals and any product with a nine pin serial connector are the applications the vendor names, and all of them need a complete port rather than a single transceiver. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

How many pieces are on the SSOP reel? The addendum prints 2000 and the materials table prints 1000 for the same string, so the quantity has to be named on the order.

Can the TSSOP body replace the SSOP? Only within 0 to plus 70 degrees, because the PW row is printed at that range while the DB and DW rows are minus 40 to plus 85.

What is ROUT2B for? It is the always active receiver output that stays valid with the device powered down, used for the ring indicator line.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.