SN65C3232PWR
Product Specifications
SN65C3232PWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65C3232PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65C3232PWR: a two driver, two receiver RS-232 port in a 5 mm body
The SN65C3232PWR is the compact member of the SN65C3232 family: two line drivers, two line receivers and a dual charge pump in a 16 pin TSSOP that measures 5.00 mm by 4.40 mm. It runs from a single 3 V to 5.5 V supply with four 0.1 uF capacitors, and it accepts 5 V logic inputs while powered from 3.3 V, which keeps it compatible with older controllers that still drive 5 V levels.
The speed depends on the rail. At 3 V to 4.5 V the part carries 250 kbit/s, and from 4.5 V to 5.5 V it carries 1 Mbit/s because the charge pump has more headroom for the output swing. That split matters when a product is offered in two versions: the same board with a 5 V rail moves four times the data of the 3.3 V version without a change to the silicon.
Key data for the SN65C3232PWR
| Channels | Two drivers and two receivers, the classic TX, RX, RTS, CTS four line port |
| Supply | 3 V to 5.5 V single rail, four 0.1 uF capacitors at 3.3 V and 0.33 uF on the negative pump at 5 V |
| Speed | 250 kbit/s from 3 V to 4.5 V, 1 Mbit/s from 4.5 V to 5.5 V, slew rate 18 to 150 V per microsecond at 3.3 V |
| Current | 0.3 mA typical and 1 mA maximum with no load, which is what makes the part usable on a bus powered node |
| Protection | 15 kV HBM on the receiver inputs and driver outputs, 3 kV on the remaining pins, 1.5 kV charged device model |
| Skew | 300 ns maximum pulse skew between the two edges of one channel, 1000 ns settling into a 1000 pF load |
Body, marking and reel data
| Body | PW, TSSOP 16 at 5.00 mm by 4.40 mm, the smallest of the four bodies the family publishes |
| Reel | 2000 pieces on a large reel, carrier tape 12.4 mm wide, 330 mm reel |
| Marking | CB3232 on the plain, .A and G4 rows, so the reel label is the only thing that separates them |
| Temperature | Minus 40 C to 85 C on the plain SN65C3232PWR row, 0 C to 70 C printed on the .A and G4 rows of the same string |
| Handling | Moisture level 1, 260 C peak, unlimited floor life on all three rows |
What the four line port covers in practice
A two driver, two receiver port carries transmit, receive, request to send and clear to send, which is enough for a console port with hardware handshake. That is the reason this body stays popular on industrial gateways, scales and telecom shelves: the host controller has a UART with flow control pins, the panel has a DE9 connector, and nothing else is needed between them. Software flow control instead of hardware handshake frees the second driver for a second connector, and the part supports that too.
Because the charge pump is internal, the negative rail for the driver is generated on chip. The 0.1 uF capacitors have to be placed close to the C1 and C2 pins with a short ground return, and the vendor asks for the 0.33 uF part on C2 to C4 at 5 V. Builders who mix capacitor values from two suppliers with different dielectric classes sometimes see the negative rail sag at 1 Mbit/s, and the cure is a stable X7R part rather than a larger value.
Questions we get when this code is on a BOM
The addendum is where the surprises are. The plain SN65C3232PWR row prints the package as SOIC (DW) with a minus 40 C to 85 C range, while the .A and G4 rows of the same order string print TSSOP (PW) at 0 C to 70 C. The string ends in PW, so the TSSOP body is the one a buyer expects, and the SOIC label on the plain row reads as a column shift in the vendor file. We confirm the body on every offer rather than trusting the package column.
The other question is whether a 16 pin part can drive a cable at 1 Mbit/s. The answer depends on the load: the 1 Mbit/s figure is published into a 250 pF load at 5 V, and a long unshielded cable adds capacitance quickly. A short rear panel cable is fine, a 15 m run is not, and we say that before the part is committed.
How SUPERB supports this line item
The SN65C3232PWR is a stocked catalogue line for us, supplied with the row suffix, the body and the temperature grade named on the offer. Where the board can accept a different body, our pin to pin cross reference page shows how we compare the four packages of this family pin by pin before proposing a swap.
For customers moving a serial interface from an older 5 V transceiver, how to verify a drop in replacement lists the four things we check on the bench: pinout, capacitor network, logic thresholds and the data rate at the actual rail voltage.