Contact Us

SN65C3232DR

Brand: Texas Instruments
Texas Instruments SN65C3232DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65C3232DR — Power Management & Signal Chain | Superb Automation

SN65C3232DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65C3232DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65C3232DR: dual RS-232 driver and receiver on 3 V to 5.5 V with a charge pump inside

SN65C3232DR is a two channel RS-232 interface that makes its own positive and negative rails from a single 3 V to 5.5 V supply with four small capacitors, for a serial port on a board that has no other negative rail in a SOIC body of 16 pins. It contains two line drivers, two line receivers and a dual charge pump, runs at up to 1 Mbps, draws 300 uA typical, needs four external 0.1 uF capacitors, accepts 5 V logic inputs while running from 3.3 V, and carries plus or minus 15 kV human body model protection on the serial port pins including ground. The driver slew rate is specified from 24 V per microsecond to 150 V per microsecond, which is the window that keeps a cable from radiating while still meeting the RS-232 transition requirement.

Order code and package

SN65C3232DRSOIC D body, 16 pins, 9.90 mm by 3.91 mm, Active in the addendum dated 10 August 2026, 2500 pieces on a large reel, NIPDAU finish, moisture level 1 with unlimited floor life, minus 40 to plus 85 degrees, marking 65C3232
SN65C3232D and SN65C3232DWthe tube rows in the D and DW bodies, for a small build or a socketed board. The plain D tube row is printed Obsolete, so a tube order needs the other body or a distributor stock check
SN65C3232DBRthe 16 pin SSOP body, 2000 on a large reel, for a board that cannot take the wider SOIC
SN75C3232the commercial temperature version of the same part, 0 to 70 degrees, with a different top mark. It is the same electrical function and a different qualification
Against a 5 V only parta MAX232 class device needs a 5 V rail and four capacitors of 1 uF or more. This part works down to 3 V and uses 0.1 uF, which is the difference on a 3.3 V board with no 5 V rail

Electrical parameters that decide the application

Supply3 V to 5.5 V, so the same part works on a 3.3 V board and on a legacy 5 V board, and the charge pump makes the plus and minus rails internally
Signalling rateup to 1 Mbps, well above the 20 kbps of an old serial port and enough for a modern console or a firmware download link
Drivers and receiverstwo of each in one package, so a port with hardware flow control fits in one device instead of two
Charge pump capacitorsfour external 0.1 uF capacitors, small ceramics rather than the 1 uF electrolytics an older part needs, which is a board area and a lifetime decision
Supply current300 uA typical, which is low for an RS-232 interface and is the reason the part appears on battery powered instruments
Logic levels5 V logic inputs are accepted while the part runs from 3.3 V, so a 5 V controller can drive it directly and a 3.3 V controller sees a valid output
ESDplus or minus 15 kV human body model on the serial port connection pins including ground, which is the level a cable plugged into a panel connector sees
Slew rate24 V per microsecond minimum and 150 V per microsecond maximum on the driver output, the RS-232 window that keeps emissions and crosstalk bounded
Output swingthe drivers produce the plus and minus levels RS-232 needs from the internal charge pump, so no external negative supply is required
Receiver thresholdthe standard RS-232 window, so a receiver sees a valid level from a legacy device that swings the full plus or minus 12 V
Pin count16 pins for two drivers, two receivers and the charge pump, which is the minimum for a full flow control port
Temperatureminus 40 to plus 85 degrees on the printed D rows, with the 75 prefix part covering 0 to 70

Family variants and how they differ

65C3232 against 75C3232the same function at two temperature grades and two prices. The 65 covers minus 40 to plus 85, the 75 stops at 0 to 70, and the top marks differ so a mixed reel is visible on the line
3232 against 3243the 3243 is a three driver, five receiver part for a full modem port. A console port needs two and two, and the smaller part leaves board area for the connector
Against a USB bridgea USB to serial bridge removes the RS-232 transceiver and the connector, and needs a driver on the host. A product with a legacy DB9 port keeps the transceiver
Against an isolated RS-232 partan isolated interface puts a barrier on the port for a link that crosses a ground difference. A port inside one enclosure does not need it
Against a discrete charge pumpfour capacitors and two ICs versus one package and four capacitors. The integrated part is smaller and its charge pump is specified as a unit with the drivers

Points to check before this part goes on a BOM

The four capacitors are part of the specification and not a suggestion. The charge pump is specified with 0.1 uF ceramics, and a board that uses 1 uF because that is what was in the bin will still work at room temperature and will show a lower output swing at the cold end, where the ceramic loses capacitance. The capacitor dielectric and its voltage coefficient belong in the incoming inspection, not just the value.

The 300 uA typical supply current is the quiescent figure with no load on the drivers. An RS-232 driver driving a 3 kohm load at plus or minus 5 V delivers milliamps, and the supply current follows with the charge pump efficiency. A battery powered product that keeps the port idle should park the drivers, and this part has no shutdown pin, so that decision is made in the controller.

The plus or minus 15 kV rating covers the connector pins including ground, which is the correct scope for a panel mounted port. It does not cover a surge on the cable from a nearby strike, and it does not cover a mistake where the port is wired to a telephone line. Both of those are external protection decisions.

The tube row for the plain D body is obsolete while the reel row is active, and that pattern is common on older parts. A prototype order that asks for a tube gets the part in a different body or a distributor's remaining stock, and the board has to accept the DW or the DB footprint. Checking the body before the first build is cheaper than a respin.

The 1 Mbps rate is limited by the slew rate window as much as by the silicon. The driver is specified between 24 and 150 V per microsecond, and at 1 Mbps with a long cable the transition is the dominant term. A customer who needs the rate over 15 m of cable is asking for a cable and a slew rate that the standard does not pair.

The RS-232 levels are made by the charge pump from the logic rail, so the port output swing depends on the 3.3 V or 5 V rail being clean. A rail with 200 mV of ripple at the switching frequency appears on the RS-232 output as a common mode term, and a receiver at the far end with a marginal threshold will show it as framing errors.

Why the charge pump stays inside the part

RS-232 needs plus and minus rails that are larger than the logic supply, and a board with only 3.3 V has no negative rail at all. The charge pump doubles and inverts the supply with four capacitors, and integrating it removes the inductor, the diode and the switching node that a discrete solution would need.

The trade is that the charge pump is only as good as its capacitors. Their value, their dielectric and their voltage rating set the output swing under load and at temperature, and the four 0.1 uF parts on the bill of materials are as much a part of the interface as the IC.

What the order code decides

The string reads SN65C3232 for the device, D for the SOIC body and R for the large reel of 2500. The DW and DB letters are the wider SOIC and the SSOP, and the 75 prefix is the commercial temperature grade. The 3243 is a different device with three drivers and five receivers, not a variant of this string.

Where this order code fits

Industrial PCs, wired networking equipment, data centre and enterprise computing, battery powered systems, notebooks and handheld equipment are the applications the vendor prints, and a console or service port on a 3.3 V board is the case this part is bought for. Teams comparing it with a neighbouring part start from our Component Lead Time Solutions page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does SN65C3232DR need a negative supply? No. The dual charge pump makes the positive and negative RS-232 levels from the 3 V to 5.5 V rail, using four external 0.1 uF capacitors.

What data rate does it support? Up to 1 Mbps, with a driver slew rate between 24 and 150 V per microsecond.

Is the tube version available? The plain SN65C3232D tube row is printed Obsolete. The active rows are the reel strings in the D, DW, DB and PW bodies.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.