Contact Us

SN6505ADBVR

Brand: Texas Instruments
Texas Instruments SN6505ADBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN6505ADBVR — Power Management & Signal Chain | Superb Automation

SN6505ADBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN6505ADBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN6505ADBVR: 1 A push-pull transformer driver for an isolated supply at 160 kHz

SN6505ADBVR is a push-pull transformer driver for isolated power in a SOT-23 body of 6 pins. It drives the primary of a centre tapped transformer with two 1 A switches from a 2.25 V to 5.5 V input, producing the isolated rail that an isolated data barrier needs on its far side. The DBVR order code is the six pin SOT-23 on a 3000 piece reel.

Order code and package

Order codeSN6505ADBVR
Package6-pin SOT-23, DBV
Packingtape and reel, 3000 pieces
Input range2.25 V to 5.5 V
Output drive1 A per switch at 5 V
Switching frequency160 kHz internal oscillator
External partscentre tapped transformer, rectifier, output capacitor
Protection1.7 A current limit, UVLO, thermal shutdown, soft start

Electrical parameters that decide the application

Switch on resistance0.25 ohm maximum at 4.5 V
Current limit1.7 A
Under voltage lockout2.25 V rising, 1.7 V falling, 0.3 V hysteresis
Shutdown currentbelow 1 microampere with the enable low
Spread spectruminternal clock modulation for lower emissions
Temperature rangeminus 55 to plus 125 degrees

Family variants and how they differ

SN6505A160 kHz oscillator, this order code
SN6505B420 kHz oscillator, smaller transformer
SN6501lower current driver in the same family
SN6505ADBVT250 piece reel instead of the 3000 piece reel

Points to check before this part goes on a BOM

The part drives a transformer and does not regulate. Output voltage follows the turns ratio and the input voltage, so a rail that must hold 5 V from a 2.5 V to 5 V input needs either a post regulator or a transformer ratio chosen for the worst case input, and the data sheet examples show both arrangements.

One ampere per switch at 5 V is a peak switch current, and the delivered power is roughly half of the input power after the transformer and rectifier losses. A barrier that needs 5 V at 100 mA is asking for about 1 W, which is inside a small transformer at 160 kHz and outside it at a much lower frequency.

The A and B versions differ only in oscillator frequency: 160 kHz here and 420 kHz on the B version. The transformer has to be chosen for the frequency it will actually see, because a part chosen for 420 kHz saturates at 160 kHz and a part chosen for 160 kHz wastes core volume at 420 kHz.

On resistance of 0.25 ohm maximum at 4.5 V means about 0.25 W in each switch at 1 A, so the package dissipation is a real constraint at the top of the current range. A 100 mA load draws only 200 mA of switch current and the loss falls with the square of that ratio.

Under voltage lockout rises at 2.25 V and falls at 1.7 V with 0.3 V of hysteresis, so a 2.5 V input runs with only 250 mV of margin and a battery that sags crosses the threshold. The 1.7 V falling point keeps the driver running through a short dip rather than restarting the isolated rail and resetting the far side.

Spread spectrum clocking modulates the switching frequency to spread emissions, which helps a module pass a conducted emissions limit. The trade is that the transformer sees a moving frequency, so the core has to be rated at the lowest frequency in the modulation band and not at the nominal 160 kHz.

An external clock can replace the internal oscillator, which allows several drivers on one board to run in step and keeps their beat frequencies out of the measurement band. That option is one reason the part is used in multi channel isolated instruments rather than a fixed frequency driver.

Transformer selection is the whole circuit around this part. The turns ratio sets the output voltage, the primary inductance sets the magnetising current at the switching frequency, and the saturation current has to exceed the 1.7 A limit. A transformer chosen only by turns ratio saturates on the first current limited start.

The output is unregulated, so a rail that must hold a tolerance needs a low dropout regulator behind the rectifier. That regulator costs headroom, which means the transformer ratio has to produce more than the required output at the lowest input voltage, and the whole chain is specified from the bottom of the input range rather than from the nominal 5 V.

Soft start limits the current a large output capacitor draws when the isolated rail first comes up. A 10 microfarad capacitor at 5 V charged through a transformer with no soft start looks like a short circuit for the first few cycles, and the 1.7 A current limit then holds the rail below its target until the capacitor has charged. A larger output capacitor makes the start slower, not the rail stronger.

Where this order code fits

It supplies the isolated side of digital isolators, isolated CAN and RS-485 transceivers, gate drivers, isolated analog front ends and medical or industrial modules that need a small galvanically separated rail. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does it regulate the output? No. The output follows the transformer ratio and the input voltage, so a regulated rail needs a post regulator or a closed loop elsewhere.

What is the difference between the A and B versions? Oscillator frequency: 160 kHz on the A and 420 kHz on the B. The transformer must be specified for the frequency in use.

How much power can it deliver? About 1 W with a suitable transformer at 5 V input, limited by the 1 A switch rating and the thermal capability of the six pin package.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.