Contact Us

SN6501DBVR

Brand: Texas Instruments
Texas Instruments SN6501DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN6501DBVR — Power Management & Signal Chain | Superb Automation

SN6501DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN6501DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN6501DBVR: push-pull transformer driver that builds an isolated rail inside a five pin SOT-23

SN6501DBVR is an oscillator and a pair of ground referenced N-channel switches in one package, built to drive the primary of a small centre tapped transformer in a SOT-23 body of 5 pins. It runs from a single 3 V to 5.5 V supply, drives 350 mA of primary current at 5 V and 150 mA at 3.3 V, switches between 400 and 550 kHz on the 3.3 V rail and between 300 and 620 kHz on the 5 V rail, and holds a break before make gap of 150 ns between the two switches. Everything on the secondary side, including the turns ratio, the rectifier and the post regulator, stays outside the part, which is why the same five pin device serves an isolated CAN port and an isolated gate drive rail.

Order code and package

SN6501DBVRSOT-23 DBV body, 5 pins, 3000 pieces on a large reel, Active in the addendum dated 10 August 2026, NIPDAU finish, moisture level 1 with no floor life limit, marking Q3, minus 40 to plus 125 degrees
SN6501DBVTthe same body on a 250 piece small reel, which is the column a prototype build or a repair order comes from, and the reel that arrives when a line needs twenty pieces rather than three thousand
SN6501DBVRG4the G4 row of the same reel, printed with the same 3000 piece quantity and the same NIPDAU finish, and the string a material declaration has to name when the customer asks for the lead free variant explicitly
SN6505A and SN6505Bthe later members of the same idea in a six pin SOT-23, with a higher current capability, a spread spectrum option and an enable pin, so a board that needs to switch the isolated rail off in standby moves one number up the family rather than adding a load switch
Diodes and capacitorsnot in the part. The centre tapped primary, the two rectifiers and the output capacitor are the bill of materials around this device, and the output voltage is set by the turns ratio and the rectifier drop rather than by a resistor divider inside the chip

Electrical parameters that decide the application

Supply3 V to 5.5 V on VCC, with 3.3 V and 5 V as the two rails the electrical table is written around, so a 3.3 V logic board and a 5 V industrial board share the same part number
Primary drive current350 mA maximum per switch at a 5 V supply with a swing of at least 3.8 V, and 150 mA per switch at 3.3 V with a swing of at least 2.5 V, which is the number that sets the transformer primary rating
Switch on resistance1 ohm typical and 3 ohm maximum, so at 350 mA the two switches together drop about 1.05 V of the primary swing in the worst case and this is the loss term that decides the efficiency at full load
Switching frequency400 to 550 kHz on a 3.3 V supply and 300 to 620 kHz on a 5 V supply, with a 300 kHz start up frequency, which puts the switching noise above the audio band and inside the band a small ferrite transformer is efficient
Break before make150 ns typical between the two switches, which is the gap that stops a shoot through through the transformer primary when the drive crosses over
Output edge times70 ns rise and 110 ns fall at 3.3 V against 80 ns rise and 60 ns fall at 5 V, which is what the transformer leakage inductance and the switch resistance produce into the primary winding
Quiescent current150 uA typical and 400 uA maximum at 2.4 V with no load, and 300 uA typical and 700 uA maximum at 3.3 V and 5 V with no load, so the driver itself costs about a milliwatt before any secondary current is drawn
Isolationset by the transformer and not by the device. The package carries no barrier rating, so the creepage, the clearance and the test voltage all come from the transformer the customer selects, and the datasheet section on recommended transformers is the list to quote from
Output voltageany value the secondary can be wound for. The rectified output follows the turns ratio and the load, and a low dropout regulator after the rectifier is the normal way to turn that into a fixed 5 V or 3.3 V isolated rail
Ripplethe push-pull drive at twice the switching frequency with a small output capacitor is what keeps the ripple low enough for a linear regulator to follow, and the datasheet calls the low rectified ripple out as the reason small capacitors work here
Temperatureminus 40 to plus 125 degrees ambient, the full industrial range, with the thermal table giving a junction to ambient figure of 208 degrees per watt in the DBV body
Ordering precisionthe reel size is the difference between DBVR and DBVT. The R suffix is a large reel and the T suffix is a small reel, and a purchase order that names the base number only can be filled either way

Family variants and how they differ

SN6505A against SN6505Bthe later pair in a six pin body adds an enable pin, a soft start and up to 1 A of switch current, and the A and B letters select the switching frequency band, which is the option to read when a board needs the isolated rail to start in a controlled ramp
SN6501 against a modulean isolated DC to DC module in a single package takes no external transformer and passes a certification file with it, at three to five times the board area and a fixed output. The driver plus transformer route wins when the output voltage or the barrier has to be chosen
Against a push-pull controllera controller with an external pair of MOSFETs carries far more power, but it also carries a gate drive loop, a current sense and a compensation network. This part is the smallest complete answer for a rail under about 1 W
Against a charge pumpa charge pump inverter needs no magnetic part, but it cannot hold isolation and it cannot deliver the tens of milliamps an isolated RS-485 port draws, so it is not a substitute in this slot
Against an opto coupled supplyan opto plus a discrete oscillator was the older route to the same rail, with more parts, a worse efficiency and a lifetime that follows the opto. The transformer driver removes the opto from the power path

Points to check before this part goes on a BOM

The first number to check is the primary current against the transformer, not against the load. At 5 V the part drives 350 mA into the primary, and with a 1 to 1 ratio that is 350 mA of secondary current before losses, which is roughly 1.7 W at 5 V out. A customer asking for a 1 W isolated rail has margin, and a customer asking for 2 W from a 3.3 V supply is asking this part to do something the 150 mA figure does not allow.

The output is unregulated, and that is the property that surprises buyers most often. The rectified secondary falls as the load rises because the primary current is limited by the switch resistance and the transformer leakage, so the datasheet curves show the output against load rather than a flat line. A 5 V rail that has to stay inside five per cent needs a linear regulator after the rectifier, and the drop across that regulator at full load is what the turns ratio has to be chosen for.

The 150 ns break before make is what makes the push-pull safe, and it is also why the part cannot be replaced by two plain MOSFETs driven from a microcontroller pin pair. A firmware driven bridge without that gap turns both switches on for the length of one instruction and the transformer saturates. Teams that move from a discrete bridge to this part usually find the rail quieter and the current lower, and the reason is that gap plus the fixed frequency.

The transformer is the part of the order that fails first in production. Recommended transformers are listed in the datasheet with their turns ratios, their isolation ratings and their footprint, and a substitute with the same footprint but a different leakage inductance changes the output curve. When a customer sends a bill of materials with a transformer that is not on that list, the honest answer is that the rail will work but the output against load curve has to be measured rather than assumed from the table.

The five pin body carries no isolation rating of its own, so a claim about barrier voltage belongs to the transformer and to the spacing on the board, not to this device. That matters at the quoting stage: an offer that lists 2.5 kV of isolation against SN6501 is describing something the part does not contain, and a test house reading the offer will ask which component provides it.

The G4 and plain rows differ only in the finish declaration. Both are NIPDAU in the current addendum, and the G4 string exists so a customer who asks for the lead free variant by name can be quoted the row that matches. Substituting the plain row for a G4 order is normally harmless in function and still wrong on the paperwork, and paperwork is what an incoming inspection checks.

Where the isolated rail comes from

The device drives a centre tapped primary with two switches in antiphase, so the secondary sees an alternating square wave at the switching frequency and a pair of rectifiers turns it into a DC rail. That is why the output can be any voltage, why the ripple is at twice the switching frequency, and why the output capacitor can be small: the ripple frequency is high and the duty cycle is fixed at fifty per cent by the internal logic.

The usual chain is driver, transformer, two Schottky rectifiers, a capacitor and then a low dropout regulator. The regulator sets the final accuracy and the rejection of the switching ripple, and the transformer sets the isolation. Removing the regulator to save cost leaves a rail that moves with load, which is acceptable for a gate drive bias and not acceptable for an ADC reference.

What the order code decides

The string reads SN6501 for the device, DBV for the five pin SOT-23 and R for a large reel. The T in the same position is a small reel, and the G4 suffix is the lead free declaration row. Nothing in the string selects the switching frequency or the current, because this device has one version of each, which is why a buyer comparing it with the SN6505 family has to look at the extra pin and the enable function rather than at a suffix.

Where this order code fits

Isolated interface supplies for CAN, RS-485, RS-422, RS-232, SPI, I2C and low power LAN, industrial automation, process control and medical equipment are the applications the vendor names, and every one of them needs a few tens of milliamps behind a barrier rather than a watt. Teams comparing it with a neighbouring part start from our Component Lead Time Solutions page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can SN6501DBVR supply a 1 W isolated rail? At 5 V it drives 350 mA into the primary, which is about 1.7 W at a 1 to 1 ratio before losses, so 1 W is inside the part with margin. At 3.3 V the 150 mA figure puts the practical ceiling near 0.7 W.

Does it regulate the output? No. The output follows the transformer ratio and the load, and a linear regulator after the rectifier is what makes the rail accurate. The part sets the switching and the drive, not the voltage.

Does the part provide the isolation? No. Isolation comes from the transformer, its creepage and the spacing on the board. The five pin body carries no barrier rating.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.