OPA340PA
Product Specifications
OPA340PA
Texas Instruments — Power Management & Signal Chain
Product Overview
The OPA340PA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
OPA340PA: rail-to-rail CMOS operational amplifier with 5.5 MHz bandwidth in an 8-pin plastic DIP
OPA340PA is a single-supply CMOS operational amplifier with rail-to-rail input and output, 5.5 MHz of bandwidth and 750 microamps of supply current in a PDIP body of 8 pins. The PA suffix is the 8-pin plastic DIP, which keeps this part available for through hole boards and for sockets that already hold an older CMOS amplifier. The input works 500 millivolts beyond either rail, the output sits within 1 millivolt of the rails into a 100 kilohm load, gain bandwidth is 5.5 MHz with 6 volts per microsecond of slew, and distortion at 1 kHz is 0.0007 percent.
Order code and package
| Order code | OPA340PA |
| Function | rail-to-rail input and output CMOS operational amplifier |
| Package | PDIP, 8 pins, body code P |
| Supply range | 2.5 V to 5.5 V |
| Supply current | 750 microamps per channel |
| Gain bandwidth | 5.5 MHz at unity gain |
| Slew rate | 6 volts per microsecond |
| Offset | 150 microvolts typical, 500 microvolts maximum at 5 V |
| Offset drift | 2.5 microvolts per degree |
| Input common mode | 500 millivolts beyond either rail |
| Output swing | within 1 millivolt of either rail into 100 kilohms |
| Datasheet | OPAx340, OPA2340, OPA4340 single-supply family document |
Electrical parameters that decide the application
| Distortion plus noise | 0.0007 percent at 1 kHz |
| Power-supply rejection | 30 microvolts per volt typical, 120 microvolts per volt maximum over temperature |
| Short-circuit current | 50 milliamps |
| Output into 10 kilohms | within a few millivolts of the rails, and 1 millivolt into 100 kilohms |
| Input capacitance | small signal CMOS input, bias current in the picoamp range |
| Unity gain stability | stable at a gain of one without an external compensation capacitor |
| Package family | SOT-23-5 and SOIC for the single, SOIC and VSSOP for the dual, SSOP for the quad |
| Operating range | minus 40 to plus 85 C |
Points to check before this part goes on a BOM
500 microvolts of maximum offset is 0.41 of a bit on a 12 bit converter at 5 V and 6.6 bits on a 16 bit one. The part is therefore an AC and mid-resolution part: it is chosen for the rail-to-rail swing and the 0.0007 percent distortion rather than for DC accuracy, and a 16 bit DC channel wants a chopper in front of it instead of this amplifier.
The rail-to-rail input is a real 500 millivolts beyond each rail, which on a 5 V board means the input can sit at minus 0.5 V or at 5.5 V without damage. This is what allows a single-supply buffer to accept a signal that overshoots the rail, and it is also why the input pair changes over near mid-rail. The distortion figure of 0.0007 percent is measured in a configuration that does not cross that region, so a stage biased at exactly half supply should be checked on the bench.
The output sits within 1 millivolt of either rail into 100 kilohms, which is close enough that a 12 bit converter on the same 5 V rail can use the full code range. Into 10 kilohms the swing is a few millivolts less, and into 600 ohms the output stage current limit becomes the constraint rather than the swing. Driving a 50 ohm cable directly is outside what 50 milliamps of short circuit current will do cleanly.
5.5 MHz with 6 volts per microsecond is a balanced pair: at a 2 V peak to peak signal the slew rate allows about 477 kHz, and at a gain of 10 the bandwidth allows 550 kHz, so neither limit dominates across the useful range. That balance is why this amplifier is common in 100 kHz active filters, where both the gain and the slew rate have to hold at the same frequency.
750 microamps per channel at 5 V is 3.75 milliwatts, and a quad in the same family is 15 milliwatts. The choice against a 10 MHz part is therefore mostly about current: 400 microamps buys 10 MHz in a newer CMOS process, while this part spends 750 microamps on 5.5 MHz but delivers 0.0007 percent distortion and a 50 milliamp output stage that the lower current part does not have.
2.5 microvolts per degree of drift over 125 degrees is 312 microvolts, which is more than half the room temperature offset window. A channel that is trimmed at 25 C therefore drifts by two thirds of a bit at 12 bits over the industrial range, so trimming is worth doing only when the trim network itself is stable, and on most boards the answer is to leave the offset and accept the 0.41 bit error.
Where this order code fits
Audio and active filter stages, ADC input buffers, portable instrument front ends and 5 V signal chains use this part because the rail-to-rail input removes the need for a negative supply and the distortion figure is low enough for a 16 bit audio path. The DIP body also keeps it usable on older through hole assemblies. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the ADC DAC Cross Reference page.
Questions buyers ask
Can the OPA340 input go above the positive supply? Yes, 500 millivolts beyond either rail. That is the defined input range, and it is not the same as the absolute maximum, which is a diode drop beyond the rails.
Is this part suitable as a 16 bit ADC driver? For AC signals with filtering, yes, because the distortion and the swing are good. For DC accuracy it is not, since 500 microvolts is 6.6 bits at 16 bits on a 5 V range.
Why choose the DIP body at 5.5 MHz? Availability on through hole boards and in existing sockets. The same die is offered in SOT-23-5 and SOIC when the assembly is surface mount.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.