Contact Us

OPA237UA

Brand: Texas Instruments
Texas Instruments OPA237UA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA237UA — Power Management & Signal Chain | Superb Automation

OPA237UA

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA237UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA237UA: single-supply operational amplifier with 750 microvolt maximum offset in an 8-pin SOIC

OPA237UA is a single operational amplifier that runs from one 2.7 V to 36 V supply, with an input common mode that reaches below the negative rail in a SOIC body of 8 pins. The UA suffix on this order code is the 8-pin SOIC body, which carries a junction to ambient figure of 180.4 C per watt against 115.8 C per watt for the same die in SOT-23-5. The amplifier is specified at 2.7 V and at 5 V and at 30 V, so the numbers that matter depend on which rail the board actually uses: gain bandwidth is 1.2 MHz at 2.7 V and 1.4 MHz at 5 V, and the offset window at the low rail is 250 microvolts typical and 950 microvolts maximum with the input held 1 V above ground.

Order code and package

Order codeOPA237UA
Functionsingle operational amplifier, single or dual supply
PackageSOIC, 8 pins, body code D
Supply range2.7 V to 36 V total, or plus or minus 1.35 V to plus or minus 18 V
Supply current350 microamps maximum
Gain bandwidth1.2 MHz at 2.7 V, 1.4 MHz at 5 V
Slew rate0.45 volts per microsecond at unity gain
Input common mode200 millivolts below the negative rail to 1.5 V below the positive rail
Output swingto within 10 millivolts of ground, 1 V from the positive rail
Offset trimno trim pins on the single in this body
Junction rangeminus 40 to plus 85 C
DatasheetSBOS057B, revision of April 2025

Electrical parameters that decide the application

Offset at 2.7 V250 microvolts typical, 950 microvolts maximum, common mode at 1 V
Offset drift2 microvolts per degree typical, 7.5 microvolts per degree maximum
Input bias current10 nanoamps typical, 40 nanoamps maximum
Input offset current0.5 nanoamps typical, 10 nanoamps maximum
Voltage noise28 nanovolts per root hertz at 1 kHz, 1 microvolt peak to peak from 0.1 to 10 Hz
Current noise60 picoamps per root hertz at 1 kHz
Common-mode rejection71 dB minimum, 85 dB typical
Open-loop gain75 dB minimum, 88 dB typical into 10 kilohms
Settling to 0.01 percent8 microseconds on a 1 V step
Short-circuit current7 milliamps sourcing
Thermal resistance180.4 C per watt in SOIC, 115.8 C per watt in SOT-23-5

Points to check before this part goes on a BOM

The 750 microvolt headline belongs to a 5 V supply. At 2.7 V the same table gives 950 microvolts maximum, and that is 0.78 of a least significant bit on a 12 bit converter running from the same 2.7 V rail, where a bit is 660 microvolts. A 12 bit channel that expects one bit of total error cannot spend it all on the amplifier offset, so this part belongs on a 10 or 12 bit channel with calibration, not on an uncalibrated 16 bit one.

Drift is the term that outgrows the offset. At 7.5 microvolts per degree over the 125 degree industrial span the drift alone is 938 microvolts, which is the same size as the maximum offset at room temperature. Trimming the amplifier at 25 C therefore buys nothing on a board that has to hold its reading from minus 40 to plus 85 C unless the trim network drifts with the amplifier, and a network that does that is more expensive than the next grade up.

Bias current sets the source impedance ceiling. At 40 nanoamps maximum, a 10 kilohm source contributes 400 microvolts, a 100 kilohm source contributes 4 millivolts, and a 1 megohm source contributes 40 millivolts. Anything above roughly 10 kilohms of source resistance is being measured through the bias current rather than through the signal, which is why this part is a poor match for a photodiode or a high impedance bridge.

The input range is asymmetric and it matters on a single supply. The common mode reaches 200 millivolts below the negative rail, so ground sensing works, but it stops 1.5 V below the positive rail, which on a 5 V board leaves 3.5 V as the ceiling. A high side current sense at 4.5 V, or a divider that parks the input near the rail, is outside the specified window and the output will follow the wrong node.

0.45 volts per microsecond is the real bandwidth limit for large signals. With a 4 V peak to peak sine the slew rate allows 0.45 divided by two pi times 2 V, which is about 36 kHz, while the 1.4 MHz gain bandwidth would allow 140 kHz at a gain of 10. On any signal above a volt or so this amplifier is slew limited long before it is gain limited, and a 100 kHz square wave arrives as a rounded edge.

350 microamps maximum is modest until the count grows. Ten of these on a 5 V rail draw 17.5 milliwatts, and the SOIC body adds 180.4 C per watt on top of that, so the thermal question is negligible here but the supply current is not free on a battery board. The same die in SOT-23-5 halves the thermal resistance and is the better choice when the part sits next to a regulator.

Where this order code fits

Battery and 5 V industrial boards use this part as a general signal stage where the input has to work near ground, and the swing to within 10 millivolts of ground with a 100 kilohm load makes it a workable low-side sensor amplifier. It also appears in older instrumentation where a 36 V supply ceiling is needed and the offset budget is loose. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is the OPA237UA the same amplifier as the OPA2237 in the same datasheet? Yes, same silicon and same table. The OPA237 is the single and the OPA2237 is the dual in SOIC or VSSOP, and the two share every specification except channel separation and package thermal figures.

Can this part run from a 3.3 V rail? Yes, 2.7 V is the minimum specified supply. Note that the offset window widens to 950 microvolts at that rail and the gain bandwidth drops to 1.2 MHz, and the output can then only reach 2.3 V on the high side.

Does the amplifier need a negative supply to sense ground? No. The input common mode goes 200 millivolts below the negative rail, so a ground referenced signal is inside the window with a single supply, and the output swings to within 10 millivolts of ground with a 100 kilohm load.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Obsolete RF Part Replacement page sets out the checks that keep a substitute from failing on the bench.