Contact Us

LMK6CE04800DDLFR

Brand: Texas Instruments
Texas Instruments LMK6CE04800DDLFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LMK6CE04800DDLFR — Power Management & Signal Chain | Superb Automation

LMK6CE04800DDLFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The LMK6CE04800DDLFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LMK6CE04800DDLFR: a 48 MHz LVCMOS clock from a bulk acoustic wave resonator

The LMK6CE04800DDLFR is a fixed 48.000 MHz oscillator in the LMK6C group, the single ended LVCMOS branch of the LMK6x family. Inside the package a bulk acoustic wave resonator takes the place of a quartz blank, and a fractional divider turns the resonator output into the exact frequency the board needs. Because the resonator sits on the same die as the oscillator circuit, the part arrives factory trimmed and needs no load capacitors, no tuning and no crystal qualification step at goods inwards.

Frequency coverage for the LMK6C group runs from 1 MHz to 200 MHz, and the jitter figure for this branch is 350 fs typical and 500 fs maximum root mean square over the 12 kHz to 20 MHz band at 100 MHz. That is not the lowest number in the family, and it does not need to be. An LVCMOS clock at 48 MHz usually feeds a microcontroller, a USB controller, an Ethernet PHY or an audio subsystem, where 500 fs of integrated jitter sits well below what the receiving block can resolve.

Total frequency stability is plus or minus 25 ppm, and that figure already includes ten years of aging together with every other drift term the vendor specifies. Start up time is under 5 ms, so the clock is present before a controller has finished its own reset sequence. The integrated low dropout regulator gives about 72 dBc of power supply rejection at 500 kHz of ripple, which is what keeps a switching regulator on the same rail from turning into phase noise.

Key data for the LMK6CE04800DDLFR

OutputLVCMOS, single ended, 48.000 MHz fixed at the factory
Frequency range1 MHz to 200 MHz for the LMK6C group, any fixed value inside that window
Jitter350 fs typical and 500 fs maximum root mean square, 12 kHz to 20 MHz, measured at 100 MHz
StabilityPlus or minus 25 ppm total, inclusive of ten years of aging
Supply2.5 V or 3.3 V nominal at plus or minus 5 per cent on the A rating rows, 1.8 V on the B rows
Current45 mA typical and 62 mA maximum at 100 MHz from 2.5 V or 3.3 V with the load connected, so 48 MHz draws less
Start upUnder 5 ms from power on to a valid clock
Control pinPin 1 output enable, active high or left open on the E option

Body, packing and marking data

BodyVSON DLF, 4 pins, 2.5 mm by 2.0 mm, the smaller of the two package sizes in the family
Packing3000 pieces on a large reel on the published row of this string
FinishLead finish marked Call TI on the summary row, moisture level 1, 260 C peak, unlimited floor life
TemperatureMinus 40 C to plus 105 C, which is the LMK6C grade and one step wider than the differential members

Order code note before you place the string on a purchase order

Read the code from the left. LMK6 is the family, C is the LVCMOS output, E puts the output enable on pin 1, 04800 is the frequency code, and DLF is the 2.5 mm by 2.0 mm body with R standing for the large reel. The letter that follows the frequency is the one to watch. The decoder in the document explains A as 2.5 V to 3.3 V over minus 40 to 85 C and B as 1.8 V over the same window, and it does not explain D at all, while the addendum row for this exact string prints minus 40 to 105 C.

That gap matters because an inspector comparing the code against the decoder will not find the letter. The practical answer is to confirm the supply voltage in writing before the first order and to check the reel label against the addendum row rather than against the decoder picture. The same family is also split across two bodies, so a 48 MHz requirement that has to sit in a 3.2 mm by 2.5 mm land pattern cannot be filled by this string without a footprint change.

Where a 48 MHz single ended clock earns its place

USB 2.0 controllers, Ethernet PHYs, microcontrollers with an external clock input and audio converters all take a single ended clock in this range, and each of them cares about a different number. The PHY cares about jitter and about the tolerance over temperature, the audio part cares about phase noise close to the carrier, and the controller usually cares about nothing except that the clock is present within a few milliseconds of power on.

When a board is moving off a quartz oscillator because the lead time on the crystal part has stretched, the component lead time solutions page covers the qualification steps that a swap of this kind needs, and the pin to pin cross reference page is the place to check whether the land pattern and the enable pin behave the same way as the part being replaced.

Questions we get on this code

The first question is whether a bulk acoustic wave part can be treated like a crystal. It cannot, in one respect. There is no external load capacitor to tune, so the frequency is what the factory programmed and the board contributes nothing to it. That removes one production step, and it also removes the escape route of trimming a frequency at test.

The second question is about the enable pin. On this option the pin is active high, and leaving it open enables the output. A board that expects a low to enable the clock will hold the output off, and the symptom looks like a dead oscillator. The standby current on this family is 6 mA typical and 13 mA maximum, which is the figure to use when the clock is parked rather than removed from the board.