LM311D
Product Specifications
LM311D
Texas Instruments — Power Management & Signal Chain
Product Overview
The LM311D from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LM311D: the commercial grade strobed comparator in a tube for prototypes
LM311D is the single high speed differential comparator of the LM111, LM211 and LM311 family in the eight pin small outline body, supplied in a 75 piece tube, guaranteed from 0 to plus 70 degrees. It is the member of the family that a lab reaches for first, because the tube is the carrier that survives a prototype bench and because the commercial window covers every room the board will see before it is qualified.
The part is older than most of the engineers who use it, and that is the point. The pinout is shared with several vendors, the output stage can sit on a 50 volt rail, and the response time of 115 nanoseconds is fast enough for a zero crossing detector in a switching supply. A comparator that does all three is easy to keep in a bill of materials.
What follows is the detail that a distributor page leaves out: which electrical rows decide a threshold, how the strobe and balance pins have to be driven, what the output does into a 24 volt load, and what the tube carrier means for a build that is still in prototype.
What the part is and what the code says
LM is the family prefix, 311 is the commercial grade of the input stage, and D is the eight pin small outline body. There is no carrier letter, which in this family means the tube, and that is the only difference between this string and the reel code that carries the same die.
The grade matters more than the carrier. The LM111 is guaranteed from minus 55 to plus 125 degrees, the LM211 from minus 40 to plus 85, the LM211Q from minus 40 to plus 125 and the LM311 from 0 to plus 70. Each grade carries its own table, so the offset window printed for the LM311 at room temperature is not the window that holds at 125 degrees on the LM211Q.
| Orderable code | LM311D |
| Channels | 1, differential input, strobed |
| Body | SOIC, 8 pins, 4.9 by 3.9 millimetres nominal |
| Carrier | tube, 75 pieces |
| Temperature window | 0 to plus 70 degrees |
| Lead finish | nickel palladium gold, level 1 moisture rating at 260 degrees |
| Part marking | LM311 |
| Family document | SLCS007K, first issued September 1973, revised March 2017 |
The rows that decide a threshold
Offset voltage is 0.7 millivolts typical and 3 millivolts maximum at 25 degrees, widening to 4 millivolts across the full range. That is a narrow window for a part of this age, and it is the reason the family survived in analogue threshold chains long after faster comparators appeared.
Input bias current is 75 nanoamps typical and 100 maximum, and offset current is 4 nanoamps typical with 10 maximum, which sets the source impedance the input can tolerate. A 100 kilo ohm divider with 100 nanoamps of bias current sits 10 millivolts off, three times the offset window, so the divider belongs in the low kilo ohm range or the bias current has to be balanced on both inputs.
| Input offset voltage at 25 degrees | 0.7 millivolts typical, 3 maximum |
| Input offset voltage over the full range | 4 millivolts maximum |
| Input offset current | 4 nanoamps typical, 10 maximum |
| Input bias current | 75 nanoamps typical, 100 maximum |
| Common mode range on plus or minus 15 volts | minus 14.5 to plus 13 volts |
| Large signal gain | 40 volts per millivolt minimum, 200 typical |
| Response time, low to high output | 115 nanoseconds typical |
| Response time, high to low output | 165 nanoseconds typical |
| Positive supply current, output low | 5.1 milliamps typical, 6 maximum |
| Negative supply current, output high | minus 4.1 milliamps typical, minus 5 maximum |
Strobe, balance and the pins that must not float into a short
The strobe pin forces the output off whatever the differential input is doing, and the document is direct about the drive: it needs 3 to 5 milliamps, it must not be shorted to ground, and a resistor from a logic rail is the normal source. From 5 volts, 1 kilo ohm gives 5 milliamps and 1.5 kilo ohm gives 3.3, both inside the window. Ten kilo ohms gives half a milliamp and leaves the output in a state the table does not promise.
The reason for the warning is that the pin feeds a current mirror rather than a gate, so a hard short pulls an unbounded current through a small device. A board that drives the strobe from an open collector gate with no series resistor comes back from the field with a dead comparator, and the failure reads as a threshold fault rather than a drive fault.
The two balance pins are the other half of the story. A potentiometer between them with the wiper on the positive rail moves the offset through its window, and the trim is a production step set once at final test. The electrical rows assume the balance and strobe pins are open, so leaving them open is allowed and tying them somewhere is not.
The output into a load that sits above the logic rail
The output is a floating transistor with collector and emitter both brought out, rated at 50 volts and 50 milliamps. The collector can sit on a 24 volt rail while the input sits on a 5 volt rail, and the emitter output can drive a load referenced to the negative rail instead of ground. That is what keeps the part in mixed voltage boxes where a logic level comparator would need a level shifter behind it.
Saturation voltage is 0.75 volts typical and 1.5 volts maximum at 50 milliamps, so a relay or an optocoupler driven straight from the collector sees about a volt of drop at full current. That suits a 12 volt relay with 5 volts of coil margin and it does not suit a low headroom load, where a small signal MOSFET is the better switch. Leakage when the output is off is 0.2 nanoamps at 25 degrees and 0.5 microamps over temperature, which on a 100 kilo ohm pull up is 50 millivolts in the worst case, and that is the number to compare against the threshold of whatever reads it.
Why a tube still makes sense on a bench
A tube of 75 parts is the right carrier while a board is in prototype, because a reel cannot be split without losing the carrier and a feeder setup costs more than the parts. A lab that builds five boards, changes a resistor, builds five more, and repeats for a month will use 20 pieces and damage a handful, and the tube absorbs that pattern.
The handling differences are small but real. The tube body carries the same nickel palladium gold finish and the same level 1 moisture rating at 260 degrees as the reel, so nothing changes on the assembly floor when the build moves to production and the carrier changes. Our production launch checklist covers the point where the carrier changes, and the date code management page shows how a partially used tube is recorded against a build.
Questions that come with this code
Does the LM311D work at 85 degrees? Not on paper. The commercial grade is guaranteed from 0 to plus 70, and the part that holds its rows at 85 is the LM211 with the same pinout and a wider offset budget over that window.
Can the output pull down a 5 volt logic input directly? Yes, with a pull up to 5 volts on the collector and the emitter grounded. The saturation voltage of 0.75 volts typical is a valid logic low for TTL and for most CMOS inputs.
What is the fastest edge it can resolve? The response time rows are 115 nanoseconds low to high and 165 high to low for a 100 millivolt step with 5 millivolts of overdrive, so a 1 microsecond edge is comfortable and a 100 nanosecond edge is marginal. Our pin to pin cross reference page lists the faster comparators that share this footprint when the edge gets shorter.