Contact Us

LM239DRG4

Brand: Texas Instruments
Texas Instruments LM239DRG4 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM239DRG4 — Power Management & Signal Chain | Superb Automation

LM239DRG4

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM239DRG4 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM239DRG4: the current green code for the quad comparator reel

LM239DRG4 is the plain grade of the quad differential comparator in the fourteen pin small outline body, on a large tape and reel, under the current G4 material code. It is the string that most production orders actually carry, because it is the row the vendor keeps active while the older G3 code has been withdrawn.

The part behind the string is unglamorous and hard to replace. Four comparators, a supply range from 2 to 36 volts, an input range that reaches ground, and open collector outputs that can be wired together. Those four properties cover a large share of the threshold, window and fault detection circuits that sit around a power supply, and the family has been second sourced by so many vendors that a shortage is usually a paperwork problem rather than a silicon problem.

What the string declares

LM is the family, 239 is the quad comparator with the minus 25 to plus 85 window, D is the fourteen pin small outline body, R is the reel, and G4 is the current green material declaration. There is no A in the string, so this is the plain offset sort: 2 millivolts typical and 5 millivolts maximum at room temperature, widening to 9 millivolts over the full window.

Orderable codeLM239DRG4
Status on the current addendumactive
Comparators per body4, independent
BodySOIC, 14 pins
Carrierlarge tape and reel
Material codeG4, current green declaration
Offset at 25 degrees2 millivolts typical, 5 maximum
Offset over the window9 millivolts maximum
Bias current at 25 degrees25 nanoamps typical, 250 maximum
Supply voltage2 to 36 volts, split rails to plus or minus 18 volts
Supply current0.8 milliamps typical, 2 maximum
Response time1.3 microseconds typical
Outputopen collector, 36 volts, 16 milliamps sink
Temperature windowminus 25 to plus 85 degrees

The offset budget on the plain grade

Nine millivolts over the window is the number that a plain grade circuit has to absorb. On a 5 volt rail that is 0.18 percent of full scale, and on a 3.3 volt rail it is 0.27 percent. A 12 bit converter over 3.3 volts has a step of 0.8 millivolts, so the offset window is eleven codes, and a calibration table taken at one temperature will be wrong at the other end by several codes.

There are three ways to live with it. Buy the A sort and halve the window. Trim each threshold at final test with a potentiometer or a stored constant. Or make the threshold ratiometric, so the offset moves with the reference and cancels in the comparison. The third is the cheapest and the one most often skipped, because it constrains the divider to the same rail as the reference.

Bias current is the second term. At 250 nanoamps maximum and a 100 kilo ohm source, the error is 25 millivolts, five times the offset window. A circuit that worries about the offset grade and ignores the source impedance is optimizing the wrong term, which is why the divider resistor values matter more than the sort letter on a high impedance sensing node.

Reel handling, moisture and the bake question

The body is rated at moisture level 1 with an unlimited floor life at 260 degrees, which means no bake is required regardless of how long the reel has been open. That is not an invitation to leave it open on a bench. Level 1 covers moisture induced cracking during reflow and does not cover solderability, and a reel that has sat in a humid room for a year will wet differently from one that came out of a sealed bag last week.

A 2500 piece reel is a single traceability unit. It cannot be split without creating a second record, and a partial reel returned to stock is the most common source of a count that does not reconcile at the end of a build. A build of a few hundred boards is better served by a cut tape length than by a full reel, and a prototype is better served by a tube.

Where this code sits in a sourcing plan

Because the family is second sourced and cheap, the buying decision is rarely about price and usually about continuity. Two rules cover most of it. Keep one active orderable code per approved vendor on the bill of materials, and treat any change of material code as a customer approval event rather than a purchasing decision.

Our drop in replacement verification page sets out the checks we run before a substitute string is offered, and the kitting service page describes how a reel is counted, labelled and issued against a build. The BOM consolidation page covers the case where four order codes for the same die are sitting on one bill and one of them can go.

There is a second consolidation that costs nothing. If the board already carries an A grade string elsewhere in the same family, the plain grade reel is a candidate for deletion rather than the other way round, because one offset window across the board simplifies the test limits as well as the purchasing line.

Two reels of the same die on one bill

Boards often carry both the plain grade and the A sort of this comparator, because one threshold needed the tighter window and another did not. That is a reasonable engineering decision and an expensive purchasing one, since the two rows are separate part numbers, separate reels and separate feeder positions for a part that differs only in a sorted offset window.

The consolidation test is simple. Take the tightest threshold on the board, work out whether the plain grade meets it over temperature, and if it does, delete the A grade line. If it does not, work out whether the A grade is needed on the other channels as well, because buying one sort for the whole board removes a feeder change and a second date code record.

Storage, counting and the year end audit

A level 1 moisture rating means the reel can sit on a shelf without a bake, so the storage rule is about the room rather than the bag. Keep the reel in a closed cabinet away from solder paste and flux, keep the label facing out, and keep the count on the label rather than in a notebook.

At the year end audit the reconciliation is over reels, not pieces. A reel with 1600 pieces left after a build is a record that says 900 were consumed, and a board count that says 920 is a question. That question is much cheaper to answer from a kitting record than from a physical recount of a partially used reel in a bag.

There is a version of this problem that is worth preventing rather than solving. A buyer who keeps one active code per approved vendor, and who deletes the withdrawn row at the moment it is withdrawn, never faces a year end question about which material code a reel carries. The discipline costs one document per change and saves the reconciliation every December.

Questions that come with this code

Is the part lead free? Yes, G4 is the current lead free and RoHS compliant declaration, and the finish is nickel palladium gold.

Can it replace the G3 code? Electrically yes, and the body and pinout are identical. The change is a material declaration revision and needs the customer's approval on a controlled programme.

Does the window cover an industrial panel at 70 degrees inside a cabinet? The ambient rating is 85, and the offset maximum of 9 millivolts already covers the whole window, so the constraint is the local board temperature rather than the datasheet figure.

What is the response time into a 5 volt pull up? 1.3 microseconds typical with 5 millivolts of overdrive, which is the figure to use when the comparator is driving a gate rather than a relay.