LM239DR
Product Specifications
LM239DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The LM239DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LM239DR: four comparators on a 2500 piece reel
LM239DR is the quad comparator in the 14 pin SOIC body on tape and reel. It is the volume string of the family: the same die as the LM339 with a wider minus 25 to plus 85 degree window, the base offset grade, and the carrier that a placement machine expects. Most of the boards that use it are not precision instruments, and the part is chosen because four thresholds in one body is cheaper than four single comparators and four sets of decoupling.
The interesting engineering is not in the comparator. It is in how four of them share a supply, a ground, a pull-up and a board edge. A quad that is laid out as four independent circuits wastes the package; a quad that shares a reference and a pull-up node turns into a compact threshold bank with one decoupling capacitor.
The rows below are the ones that decide whether that sharing works, with the numbers from the vendor document for the LM239 grade.
The electrical rows that matter for a threshold bank
Offset is 2 millivolts typical and 5 millivolts maximum at 25 degrees, and the maximum holds over the full minus 25 to plus 85 degree window rather than widening at the ends. For a threshold bank that is a useful promise: the error does not grow with temperature inside the window, so a chain calibrated at 25 degrees stays calibrated at 70.
Bias current is 25 nanoamps typical and 250 maximum, offset current 5 nanoamps typical and 50 maximum. On a divider built from 10 kilo ohm resistors those currents are 2.5 millivolts of error in the typical case and 25 millivolts in the worst case, which is five times the offset window. That ratio is why the resistor values, not the offset grade, decide the accuracy of most threshold banks.
| Orderable code | LM239DR |
| Comparators per body | 4 |
| Body and carrier | SOIC, 14 pins, tape and reel, 2500 pieces |
| Offset at 25 degrees | 2 millivolts typical, 5 maximum |
| Offset current | 5 nanoamps typical, 50 maximum |
| Bias current | 25 nanoamps typical, 250 maximum |
| Common mode range | ground to 1.5 volts below the positive rail |
| Supply current, four comparators | 0.8 milliamps typical at 5 volts, 2 milliamps maximum |
| Supply current at 30 volts | 0.55 milliamps typical, 2.5 milliamps maximum |
| Output sink at 1.5 volts | 16 milliamps typical |
| Output saturation at 4 milliamps | 150 millivolts typical, 400 maximum |
| Response time | 1.3 microseconds typical |
| Temperature window | minus 25 to plus 85 degrees |
Supply current that does not follow the rail
The supply current of this family is set by an internal current source rather than by the rail, so it stays near 0.8 milliamps at 5 volts and 0.55 milliamps at 30 volts. That is unusual enough to be worth stating on a data sheet, and it has a practical consequence: a board powered from 24 volts does not need a bigger regulator for the comparator bank than a board powered from 5.
The worst case is 2 milliamps at 5 volts and 2.5 milliamps at 30 volts, which is the number a regulator budget should use. The quiescent figure is four comparators, not one, so a board that uses two of the four still pays for four.
Decoupling is one capacitor for the body, placed within a few millimetres of the supply pin, plus the usual bulk capacitor on the rail. The part has no internal regulator and no reference pin, so the supply rejection is whatever the input stage provides, which is adequate for threshold work and not adequate for precision measurement.
Input protection and the 0.3 volt rule
The inputs may not go more than 0.3 volts below the negative rail. Above the positive rail there is more room: one input may exceed the rail as long as the other stays inside the common mode range, and both may go to the full supply without damage. That asymmetry is the reason this family survives in boards that watch a 24 volt line with a 5 volt supply.
A signal that can go negative needs a series resistor, a Schottky clamp to ground, or a split supply. The series resistor is the cheapest and works because the input current is limited to what the resistor passes at 0.3 volts of forward bias, typically a few milliamps into the internal clamp.
On a board with long sensor cables, the input also needs a capacitor to ground and a resistor to the rail. A comparator that picks up a transient and toggles is a comparator that will be blamed for a firmware bug.
Sharing one pull-up across four outputs
Wire OR is the natural use of four open collector outputs. One pull-up, four collectors, and a node that is low when any comparator is low. That is a fault bus, a multi level alarm, or a window comparator with the outside window output taken from a single node.
The pull-up is chosen for two limits. The first is saturation: at 4 milliamps the output is guaranteed below 400 millivolts, and at 8 milliamps it is still usable but the guaranteed number is no longer printed. The second is rise time: the node rises with the pull-up against the capacitance of the trace and the four collectors, and a 10 kilo ohm pull-up with 20 picofarads gives about 200 microseconds of rise.
Where the four outputs drive different logic families, the wired OR approach needs a level shift. The output transistor is rated to 30 volts, so a 12 volt pull-up with a divider into a 3.3 volt logic input works, at the cost of a slower edge and a small standing current.
A fault bus on one node
Four open collectors on one pull-up make a fault bus. Any comparator that pulls low drags the node down, the logic behind it sees a single signal, and the firmware does not have to poll four pins. The node only rises when all four release, so the release time is the slowest of the four plus the pull-up rise.
The pull-up has to satisfy the worst case sink. One comparator sinking 4 milliamps is guaranteed below 400 millivolts, and if two pull low at once the node still sits at that level because the transistors share. What changes is the current through the pull-up, which doubles and has to be inside the resistor rating.
The node capacitance is the other limit. Four collectors, a trace and a logic input add up to 20 picofarads on a small board, and a 10 kiloohm pull-up gives about 200 microseconds of rise. A fault bus that has to react within a millisecond is comfortable; one that has to react within 100 microseconds needs a smaller pull-up.
Quad versus four singles, and where the reel wins
Four singles give isolation, independent placement and the freedom to use a different grade per threshold. A quad gives one footprint, one decoupling capacitor, one reel and a lower total cost. On a board with four thresholds that share a reference, the quad is almost always the right answer.
The reel matters for the same reason it matters on any high volume line: a 2500 piece reel runs a placement machine for hours without a reload, and the feeder setup is amortised. A tube of 50 pieces is the right carrier for a prototype and the wrong one for a production run.
Our power management cross reference page lists the quad and dual equivalents with their grades, and the date code management page covers how a reel is traced into a build.
Buying questions that come with this code
Is LM239DR the same part as LM339DR? Same die, different temperature window and offset grade. The LM339 is 0 to 70 degrees, the LM239 is minus 25 to plus 85.
Does the part work at 3.3 volts? Yes, from 2 volts, and the input range still includes ground. The response time lengthens slightly at the lower rail.
What is the difference between the DR and the D string? The carrier only. One is a reel, the other a tube.