Contact Us

LM211QDRQ1

Brand: Texas Instruments
Texas Instruments LM211QDRQ1 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM211QDRQ1 — Power Management & Signal Chain | Superb Automation

LM211QDRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM211QDRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM211QDRQ1: the same automotive comparator without the green material code

LM211QDRQ1 is the automotive temperature grade of the single strobed comparator in the eight pin small outline body, on tape and reel, ordered without the green material code. It sits one character away from the green variant that carries G4 in the same position, and the two strings are bought against the same reel size, the same die and the same temperature window.

The reason to keep both strings on a bill of materials is continuity. A programme that was released years ago may still carry the non green code, and a line that is moving to a lead free process may carry the green one, so the same assembly can show both on the same purchase order list. Knowing that they are interchangeable at the silicon level is what lets a buyer consolidate the two lines into one reel.

What the string declares, in order

LM is the family prefix, 211 is the industrial input stage in the extended temperature grade, Q is the minus 40 to plus 125 degree window, D is the eight pin small outline body, R is the tape and reel carrier, and Q1 is the automotive option that the data sheet lists with configuration control, print support and qualification to automotive standards.

Compared with the green sibling, the only difference in the string is the absence of G4. The material declaration differs, the electrical rows do not, and the moisture rating printed against the rows is level 1 at 260 degrees on both. A purchaser who consolidates the two codes is consolidating the material paperwork, not the silicon.

Orderable codeLM211QDRQ1
Channels1, differential input, strobed
BodySOIC, 8 pins, 4.9 by 3.9 millimetres nominal
Carriertape and reel, 330 millimetre reel, 12.4 millimetre tape
Temperature windowminus 40 to plus 125 degrees, Q grade
Lead finishnickel palladium gold
Moisture levellevel 1, unlimited floor life at 260 degrees
Difference from the green codematerial declaration only

The Q window read against the base grade

Offset voltage is 0.7 millivolts typical and 3 millivolts maximum at 25 degrees, and 4 millivolts maximum across the full window. The base LM211 guarantees its rows to plus 85 degrees, so the Q grade buys 40 degrees at the top with the same die, and the numbers printed for the wider window are the ones that hold at 125 degrees.

Bias current is 75 nanoamps typical and 100 nanoamps maximum at room temperature, offset current is 4 nanoamps typical and 10 maximum, and both rise at the hot end. The input stage is a bipolar pair, so the leakage doubles roughly every ten degrees of junction temperature, and at 125 degrees the bias current, not the offset, is the parameter that decides whether a high impedance divider can be used at all.

Input offset voltage at 25 degrees0.7 millivolts typical, 3 maximum
Input offset voltage over the Q window4 millivolts maximum
Input bias current75 nanoamps typical, 100 maximum
Input offset current4 nanoamps typical, 10 maximum
Common mode range on plus or minus 15 voltsminus 14.5 to plus 13 volts
Large signal gain40 volts per millivolt minimum
Response time, low to high output115 nanoseconds typical
Response time, high to low output165 nanoseconds typical
Negative supply current, output highminus 4.1 milliamps typical, minus 5 maximum

The heat path that decides whether 125 degrees is real

A 125 degree rating is a junction or ambient promise, and the difference matters. In a motor drive enclosure the ambient next to a switching stage can be 30 degrees above the air at the panel, and the comparator's own dissipation is small but not zero: 5.1 milliamps on the positive rail and 4.1 on the negative rail at plus or minus 15 volts is about 135 milliwatts, which in an eight pin small outline body with a typical 120 to 150 degrees per watt junction to ambient path is 16 to 20 degrees of self heating.

The practical consequence is that a part rated to 125 degrees ambient is not the same as a part rated to 125 degrees junction. The Q grade buys operating range, and it does not buy permission to sit on top of a heatsink. Placing the comparator away from the hot copper, keeping the pull up resistor modest and using the emitter output rather than the collector output where the load allows all reduce the self heating.

The pull up resistor deserves its own moment. With a 5 volt pull up of 1 kilo ohm the output sinks 5 milliamps when it is low, which adds 25 milliwatts to the device, and with a 10 kilo ohm pull up it sinks half a milliamp and adds 2.5 milliwatts. The lower value gives a sharper edge into a capacitive load and the higher value runs cooler. On a board at 110 degrees ambient, the difference between the two is 2 to 3 degrees of junction, which is the margin that decides whether the offset row still holds at the end of a shift.

The other thermal detail is the copper under the body. An eight pin small outline package with no copper spreading pad sits near 150 degrees per watt, and the same package on a 2 centimetre square pad on the component side drops towards 110. A comparator that measures 20 degrees of self heating on the bench can measure 30 in the box, and the temperature coefficient of the offset is the parameter that turns that into a threshold shift.

Reel, tube and the consolidation case

The orderable addendum prints the reel row as 2000 pieces on a 330 millimetre carrier with 12.4 millimetre tape, a 6.4 by 5.2 millimetre pocket 2.1 millimetres deep, and the tube body at 75 pieces per tube. Neither carrier changes the silicon, and both are printed under the LM211Q device column at minus 40 to plus 125 degrees.

The consolidation case is simple arithmetic. Two strings that differ only in the material code can be merged into one reel if the assembly is acceptable to both, which removes one line from the shortage watch list and one set of date codes from the traceability record. Our drop in replacement verification page sets out the checks we run before we sign that kind of merge off, and the traceability report page shows what is recorded per reel once a merged line ships.

There is a second consolidation that costs nothing and is often missed. The tube body and the reel body carry the same silicon and the same finish, so a prototype stock of tubes and a production stock of reels are the same line item from an engineering point of view. A buyer who keeps both strings open on the same purchase order list is buying the same part twice, and the only thing that has to be decided is which carrier the line needs at the quantity on the schedule.

Kitting is where the two carriers part company. A tube can be split across builds and the remaining pieces kept in the same labelled bag, while a reel is a single traceability unit until it is empty. For a build of a few hundred boards the reel is still the right choice, because the kitting record is then one line and the feeder setup happens once. For a build of twenty the tube is cheaper and the record is a bag with a counted quantity.

Questions that come with the non green code

Does the missing G4 mean a different lead finish? The rows print nickel palladium gold on both, and the green code is the material declaration; a customer who needs the declaration on file should order the green code and keep this one for the lines that already carry it.

Is the part still active? The addendum in this revision prints the LM211Q rows as active production, with the reel and tube rows both present, so the answer is yes at the date of the document revision.

What happens if the automotive report is asked for? The features list states the family is available in the Q-temp automotive option with configuration control and print support, and the addendum in this revision does not print a separate Q1 suffix row, so the report should be requested against the automotive revision of the body before the order is placed. Our obsolete part cross reference hub is where we keep the family notes when a grade is withdrawn.