Contact Us

ISO7742FDBQR

Brand: Texas Instruments
Texas Instruments ISO7742FDBQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO7742FDBQR — Power Management & Signal Chain | Superb Automation

ISO7742FDBQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO7742FDBQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO7742FDBQR: two channels each way at 100 Mbps

The ISO7742FDBQR is the bidirectional member of the ISO774x family: four channels, two forward and two reverse, low default, in the 16 pin shrink body. Two and two is the map for a full duplex link, a pair of request and acknowledge lines, or a serial port where the transmit and receive pairs both have to cross the barrier.

Each direction has its own buffer on its own side of the barrier, so the forward and reverse paths are specified together but behave as separate channels. Propagation delay is 6 ns minimum, 12.7 ns typical and 17 ns maximum at 5 V. Pulse width distortion is 5.9 ns on same direction channels, which is the number that matters when a data line and its clock run through the same package.

The F letter sets the default low on loss of power or signal. On this part that means a lost field supply drives both return channels low, which is the state a fault handler usually treats as an alarm rather than as a valid message. Isolation in this body is 3000 VRMS and 4242 VPK, and the wide body of the same family reaches 5000 VRMS and 8000 VPK.

Key data for the ISO7742FDBQR

ChannelsFour, two forward and two reverse, with an output enable per side
Data rate100 Mbps maximum specified on either direction
Isolation in this bodySSOP DBQ gives 3000 VRMS and 4242 VPK, the wide SOIC body gives 5000 VRMS and 8000 VPK
Supply2.25 V to 5.5 V on each side, level translation across the barrier
TimingPropagation delay 12.7 ns typical and 17 ns maximum at 5 V, pulse width distortion 5.9 ns same direction
ImmunityCMTI 100 kV per microsecond typical and 85 kV per microsecond minimum
Default stateOutput low on loss of input power or signal, the F variant

Body, packing and marking data

BodySSOP DBQ, 16 pins, 4.9 mm by 4.9 mm
Packing2500 pieces on a large reel on the plain and the A row
FinishNIPDAU, moisture level 2, 260 C peak, one year floor life
Marking7742F on the body, which does not show the body size to the eye
TemperatureMinus 55 C to plus 125 C

Two directions, one barrier, one temperature

A full duplex link through one package means the forward and reverse paths sit within a few millimetres of each other across the same barrier. That is good for skew and bad for crosstalk if the board routes the two directions in parallel for a long distance on the same layer. Keep the pairs apart and let the barrier do its job, and the 100 Mbps rate is available in both directions at once.

The default matters more here than on an all forward part. When the isolated supply fails, two return channels fall low and the controller sees a start bit pattern on a UART, which some receivers read as a break condition. That is usually the desired outcome, but it has to be checked against the receive logic rather than assumed. Our how to verify a drop in replacement page covers that kind of functional check, and the pin to pin cross reference page covers the pin map comparison.

Where a two and two map is used

Isolated RS-485 or CAN interfaces put the transceiver on the field side and the controller on the other side, and the digital isolator carries the transmit data and the receive data in opposite directions, plus one or two enable lines. Four channels covers a transceiver with a driver enable and a receiver enable, which is why this map is common on interface cards.

Motor control uses the same part where a position sensor talks back over a second pair. Instrument front ends use it for a full duplex serial port at a rate the older optocoupler rows cannot reach, and the 100 Mbps rating leaves room for a protocol overhead that grows after the first release.

Questions we get on this code

Buyers ask whether the two directions are independent in timing. They are specified in one table but each path has its own buffer, so a forward edge and a reverse edge do not share a delay element. What they do share is the supply on each side, which is why each side needs its own decoupling close to the pins.

The second question is whether the shrink body can replace the wide body on an existing board. It cannot, because the pads and the creepage differ. The two bodies are the same die in different packages, and the substitution question is a mechanical and a certificate question before it is an electrical one.

One last point on this part: the two reverse channels share a supply pin with the forward pair on the same side, so a board that wants to disable the return path to save current cannot do it by cutting one rail. The enable pin is the only switch, and it moves the outputs to high impedance without cutting the barrier.