ISO7720DWVR
Product Specifications
ISO7720DWVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7720DWVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7720DWVR: two channels, one direction, 100 Mbps
The ISO7720DWVR is a two channel digital isolator with both channels in the same direction, packaged in the 8 pin wide body. It is the small member of the ISO772x family: 100 Mbps, 5000 VRMS, and a propagation delay of 11 ns typical and 17 ns maximum at 5 V. Where a board only needs two lines to cross a barrier, this part does the job in half the pins of a four channel device, which matters on a dense card.
The barrier is rated to 5000 VRMS for one minute under UL 1577 with a projected lifetime of more than 30 years at 1500 VRMS of working voltage, and the surge capability reaches 12.8 kV. Common mode transient immunity is 100 kV per microsecond typical with 85 kV per microsecond minimum in the electrical table, which is the figure that keeps a fast switching node from corrupting the isolated side.
Both sides accept 2.25 V to 5.5 V, so the part translates between a 2.5 V processor and a 5 V interface, or between 3.3 V and 5 V, without a level shifter. Supply current is 1.8 mA typical on the input side at 1 Mbps and rises to 2.5 mA at 100 Mbps, which is low for a part at this rate.
Key data for the ISO7720DWVR
| Channels | Two, both in the same direction on this member, with the opposite direction map in the sibling part |
| Data rate | 100 Mbps maximum specified, with higher rates possible according to the vendor note |
| Isolation | 5000 VRMS for 60 s per UL 1577, 1500 VRMS working voltage, 12.8 kV surge capability |
| Supply | 2.25 V to 5.5 V on each side, 2.25 V to 5.5 V level translation |
| Timing | Propagation delay 11 ns typical and 17 ns maximum at 5 V, with time interval error of about 1 ns on a 100 Mbps pseudo random pattern |
| Immunity | CMTI 100 kV per microsecond typical and 85 kV per microsecond minimum |
| Default state | Output high on loss of input power or signal on the plain part, low on the F part |
Body, packing and marking data
| Body | SOIC DWV, 8 pins, the wide 8 pin outline rather than the narrow SOIC 8 |
| Packing | 1000 pieces on a large reel on the plain and the A row |
| Finish | NIPDAU, moisture level 2, 260 C peak, one year floor life |
| Marking | 7720 printed on the body, without the reel or the default suffix |
| Temperature | Minus 55 C to plus 125 C |
Packing and footprint checks before the order
The 8 pin wide body is not the same land pattern as the 8 pin narrow SOIC that older isolators used. A board that is being changed from an older part has to have the pads checked, not just the pin count, because the wide body spreads the leads further apart and the pad ring will not fit the narrow footprint. This is the single most common reason a substitution fails at the first article.
The reel also differs from the rest of the family. This body ships 1000 pieces on a large reel where the 16 pin members ship 2000, so a production run needs twice the reels for the same quantity. Our component lead time solutions page covers how we plan around a reel size that differs from the family, and the pin to pin cross reference page is the right starting point for a footprint comparison.
Where a two channel wide body is used
Serial links that need only a transmit and a receive line across a barrier use this part. So do isolated gate drive channels on a small inverter, where two signals cross and the return path is not needed. The 100 Mbps rate means the part can carry an isolated USB or Ethernet style link, not only a slow control line.
The 5000 VRMS rating with a 1500 VRMS working voltage is the reinforced class, so the part covers mains referenced equipment without the extra spacing that a basic barrier would need. The one caution is the creepage across the 8 pin body: the wide outline helps, but the board still has to keep the isolation slot and the required distance from the pads to the barrier edge.
Questions we get on this code
Buyers ask whether both channels can run at 100 Mbps in the same direction. They can, and the timing table gives a single delay figure for both. What changes with two channels switching together is the supply current, which rises from 1.8 mA at 1 Mbps to 2.5 mA on the input side at the full rate.
The second question is whether the part can be used in the reverse direction by turning it around. Electrically the channels are one way on this member, so turning the package around moves the input side to the other rail, which is legal only if both rails are within the 2.25 V to 5.5 V window and the board can accept the rotated pin numbering. The sibling part with the opposite direction map is usually the cheaper answer.