ISO7641FMDWR
Product Specifications
ISO7641FMDWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7641FMDWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7641FMDWR: A 150 Mbps Quad Isolator With Three Channels Out and One Back
ISO7641FMDWR is a high speed four channel digital isolator in a SOIC (DW) body of 16 pins. It moves four digital lines at 150 Mbps each across a 6000 VPK barrier with a 7.5 ns typical propagation delay, three channels from side 1 to side 2 and one back, and the F suffix makes every output sit low when the input side loses power.
Order code and package
| Ordering string | ISO7641FMDWR |
| Package | SOIC, 16 pins, DW wide body, 10.30 mm by 7.50 mm nominal |
| Carrier | 2000 pieces on a large reel |
| Tube sibling | ISO7641FMDW at 40 pieces in a tube, same die |
| Moisture level | Level 3, 260 C peak reflow, 168 hour floor life |
| Lead finish | NIPDAU |
| Temperature range | Minus 40 to plus 125 degrees Celsius |
| Part marking | ISO7641FM |
| Channel direction | Three channels forward, one reverse |
| Default output | Low, set by the F suffix |
Electrical parameters that decide the application
| Signaling rate | 150 Mbps |
| Propagation delay at a 3.3 V input and a 5 V output | 7.5 ns typical, 12.5 ns maximum |
| Propagation delay with both rails at 3.3 V | 8.5 ns typical, 14 ns maximum |
| Pulse width distortion | 2 ns |
| Channel to channel skew | 3.5 ns same direction, 2.5 ns opposite direction at the mixed rails |
| Part to part skew | 6 ns at the mixed rails, 6.5 ns with both rails at 3.3 V |
| Rise and fall time | 1.7 ns at the mixed rails, 2 ns with both rails at 3.3 V |
| Fail-safe delay | 9.5 microseconds at the mixed rails and 9.2 microseconds with both rails at 3.3 V |
| Supply range | 2.7 V, 3.3 V or 5 V, with 5 V tolerant inputs when the part runs from 3.3 V or 2.7 V |
| Supply current per channel | 2.4 mA typical at 25 Mbps on a 3.3 V rail for this channel split, 2 mA for the all-forward member |
| Input threshold | TTL |
| Isolation rating | 6000 VPK and 4243 VRMS for one minute per UL 1577 |
| VDE ratings | 6000 VPK transient overvoltage and 1414 VPK working voltage per DIN V VDE V 0884-10 |
| Reinforced working voltage | 400 VRMS for the end equipment standards named in the document |
| Common mode transient immunity | 50 kV per microsecond typical |
| Enable pins | One per output, driving the output to high impedance |
| External clearance | Wide body, printed for the DW package in the insulation table |
Family variants and how they differ
| ISO7640FMDWR | All four channels forward, same body and same reel, for a bus that only ever sends |
| ISO7640FMDW | The same all-forward part in a 40 piece tube |
| ISO7641FMDW | This channel split in a 40 piece tube, for a first article build |
| ISO7742FDWR | The 100 Mbps successor family, 5000 VRMS, when the 150 Mbps rate is not needed |
| ISO7842FDWWR | The 8000 VPK reinforced quad in the extra wide body when the barrier has to be higher |
| ISO6741FDWR | A 50 Mbps quad at lower cost when 150 Mbps is a margin the board will never use |
Points to check before this part goes on a BOM
150 Mbps is a mid grade rate, not a top one. The same wide body is used by the 100 Mbps ISO774x and by the 8000 VPK ISO784x, so a board that later needs a stronger barrier can often keep the footprint and change the ordering string, but the pin functions have to be compared before that is assumed.
The fail-safe behaviour is low on this suffix. When the input side loses power the output goes low after about 9.5 microseconds, which is long enough for a gate driver downstream to see a low as a command rather than as a fault. A line that must read high when the far side is dead needs the non-F part.
The moisture level is 3, not 2. The floor life is 168 hours at 30 degrees and 60 per cent relative humidity, so a reel that has been open across a weekend has to be baked before reflow or the parts have to be counted as suspect.
Supply current is quoted per channel at 25 Mbps, not at the 150 Mbps ceiling. At the full rate the dynamic current rises with the switching frequency, so the rail budget has to be taken from the supply current curves rather than from the single line in the feature list.
The enable pins are per output and they put the output into high impedance, not into a defined level. A bus that shares the isolator output with another driver needs a pull resistor that holds the line where the system expects it while the channel is disabled.
Why three forward and one back is the common split
A servo interface carries a clock, a data line and an enable toward the power stage, and a fault or index signal back. That is three and one, and it is the reason this part outsells the all-forward member of the same family in motor drive boards. The reverse channel is often left unused and its input tied to the local ground, which keeps it from toggling on noise.
Where the fourth line also runs forward, the all-forward part removes the reverse channel entirely. Buyers who hold both strings on the shelf should mark them clearly, because the two reels carry the same package, the same quantity and a nearly identical marking.
Where the 6000 VPK barrier comes from
The rating is a package property in this family, not a feature of one channel count. The same barrier sits under the four channel parts and the earlier single and dual parts, which is why a board that already carries one member can usually keep the same creepage distances when it moves to another.
The 4243 VRMS figure is the one minute withstand value, and the 6000 VPK figure is a transient overvoltage rating. Quoting one where the other belongs is the most common mistake in a datasheet summary, and it matters because a surge requirement is written against the transient number.
What this part does not do
It does not translate between a 1.8 V logic domain and a 5 V domain in the way the newer families do. The supply options are 2.7 V, 3.3 V and 5 V, and the level translation works across those rails only. A 1.8 V processor needs a different member of the family rather than a resistor divider.
It also has no isolated power. The barrier carries signals only, and the far side still needs its own rail, which on most boards means a small isolated converter beside the isolator. That converter is the part that decides the channel to channel timing, not the isolator.
Two numbers the board review has to carry
The clearance and the creepage are package figures, and both are printed for the wide body in the insulation table. The pads under the part cannot shorten either distance, so the copper keep-out under the body is part of the isolation review and not a matter for the assembly house.
The 4243 VRMS figure is a one minute withstand value and the 6000 VPK figure is a transient overvoltage rating. A surge requirement is written against the second, and a certificate is written against the first, so both are needed on the same page.
Where this order code fits
It is chosen where four fast digital lines cross one barrier and the board is already laid out for the wide body, most often on a servo interface, a fieldbus node or an isolated data acquisition front end. Teams comparing it with a neighbouring part start from our Component Lead Time Solutions page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
Does the part work with a 3.3 V input side and a 5 V output side? Yes. The switching table is written for exactly that combination, with a 7.5 ns typical and 12.5 ns maximum delay, and the inputs are 5 V tolerant when the part runs from 3.3 V or 2.7 V.
What does the F suffix change? Only the state the output takes when the input side loses power or the input signal stops. The F suffix drives the output low after the fail-safe delay and the non-F part drives it high. Rate, current and barrier are identical.
Is the tube version the same silicon? Yes, ISO7641FMDW is the same die in 40 piece tubes. It matters for a first article build, because a reel of 2000 is a large commitment for a board that is still in qualification.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.