Contact Us

ISO7342FCQDWRQ1

Brand: Texas Instruments
Texas Instruments ISO7342FCQDWRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO7342FCQDWRQ1 — Power Management & Signal Chain | Superb Automation

ISO7342FCQDWRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO7342FCQDWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO7342FCQDWRQ1: A Quad Isolator With Two Channels Each Way and a Noise Filter on Every Input

ISO7342FCQDWRQ1 is an automotive qualified four channel digital isolator in a SOIC (DW) body of 16 pins. It carries two channels in each direction at 25 Mbps, adds an integrated noise filter on every input so that short spikes on a fieldbus cable do not reach the logic, and holds a 3000 VRMS basic rating with a 4242 VPK transient. The F suffix gives a low default output when the input power or the input signal is lost.

Order code and package

Ordering stringISO7342FCQDWRQ1
FamilyISO734x-Q1 in document SLLSEK5B, automotive qualified
QualificationAEC-Q100 grade 1, minus 40 to plus 125 degrees, HBM level 3A, CDM level C6
PackageSOIC, DW body, 16 pins, 10.30 mm by 7.50 mm nominal
Reel and packing2000 pieces on a large reel, NiPdAu lead finish, 40 piece tube row also published
Moisture levelLevel 2, 260 C peak, one year floor life
Part markingISO7342FCQ
Channel arrangementTwo channels forward and two reverse
Default stateLow with the F suffix, high on the same string without F
Isolation rating3000 VRMS for one minute per UL 1577, 4242 VPK basic per VDE V 0884-10

Electrical parameters that decide the application

Signalling rate25 Mbps
Propagation delay31 ns typical and 58 ns maximum with both supplies at 5 V
Pulse width distortion2.1 ns typical and 4 ns maximum
Channel to channel skew1.7 ns typical and 2.5 ns maximum on channels running the same direction
Supply range3.0 to 5.5 V on each side with 3.3 V to 5 V level translation
Input thresholdsTTL compatible, which is what allows a 3.3 V driver to feed a 5 V side
Supply current1.3 mA per channel typical at 1 Mbps on 5 V, 0.9 mA on 3.3 V
Noise filterIntegrated on the inputs, so a spike shorter than the filter window does not pass
Common mode transient immunity70 kV per microsecond typical on 5 V supplies
Maximum repetitive peak1414 VPK basic isolation
Maximum surge6000 VPK
Working voltage800 VRMS basic and 400 VRMS reinforced per CSA and IEC 60950, 300 VRMS basic per IEC 61010

Family variants and how they differ

ISO7340CQDWRQ1Four channels forward with a high default, for four signals leaving one side
ISO7340FCQDWRQ1Four channels forward with a low default
ISO7341CQDWRQ1Three forward and one reverse
ISO7341FCQDWRQ1Three forward and one reverse with a low default
ISO7342CQDWRQ1The same two by two arrangement with a high default
ISO7342CQDWQ1The 40 piece tube row of the same body, for prototypes and repair lots
ISO7742A 100 Mbps quad when the bus rate outgrows the 25 Mbps front end

Points to check before this part goes on a BOM

The document was last revised in 2017 and it certifies 4242 VPK basic under VDE V 0884-10, the older standard, not the 0884-17 used for newer families. That matters in a safety file that quotes the newer standard: the certificate exists and is valid, but it is written against the earlier issue and the file has to say so.

The working voltage rows are the ones to read carefully. The part is rated 800 VRMS basic and 400 VRMS reinforced per IEC 60950, and only 300 VRMS basic per IEC 61010. A measurement side that sits on a 400 V rail is outside all three, even though the 4242 VPK transient figure looks generous by comparison.

The integrated input filter is a help and a limit at the same time. It removes short spikes, which is why the part survives a fieldbus cable in a cabinet with contactors, but it also sets a minimum pulse width that passes. A 25 Mbps stream has a 40 ns bit, and the filter window sits inside the specification, so a board that pushes the part faster than the rated rate loses narrow pulses rather than reporting an error.

The default state is fixed by the suffix and cannot be changed at the pin. On a bus that idles high, the non F string keeps the line in its idle state during a supply loss, and the F string drives it low, which reads as a start condition or a break on some protocols. The suffix has to be chosen against the protocol, not against availability.

The four channels are not all equal in timing. The same direction skew is 1.7 ns typical while the opposite direction arrangement has its own figure, and two channels used as a differential pair therefore carry more skew than the headline suggests.

Where a two by two quad fits

Two channels each way is the shape a serial link needs at both ends. One pair carries the transmit line and its flow control signal out, the other pair brings the receive line and its ready signal back, and the whole interface crosses on one package instead of two duals. On a servo drive or a motor control card that is the usual pattern, because the field side and the control side each own two signals.

The 25 Mbps ceiling is enough for encoder feedback, for a UART based fieldbus and for the modulation signals of a power stage. It is not enough for an isolated USB or an isolated Ethernet PHY interface, both of which start at 100 Mbps and need the faster families.

What changes when the input filter is doing the work

A filtered input is more forgiving of the cable, not more forgiving of the supply. The part still needs its own decoupling on each side, and the recommended practice is a 100 nF capacitor within a few millimetres of each supply pin plus a bulk capacitor on the rail. A filtered input with a noisy rail will still produce errors, because the filter sits in the signal path and not in the supply path.

The filter also delays the edge by a small amount that is inside the propagation figure and not separately specified. Systems that calibrate a round trip delay from the datasheet timing should measure the actual board, since the board adds its own delay through the cable and the series resistors on the field side.

Where this order code fits

The part suits a fieldbus or servo interface where two signals travel each way, the cable runs through a cabinet with contactors, and the barrier only needs basic isolation. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Is the C in the ordering string a revision or a package code? It sits in the family nomenclature between the channel configuration and the Q1 automotive suffix, and the addendum prints the C and F variants as separate orderable rows with different part markings. Treat the full string as the orderable identity and do not shorten it to ISO7342Q1.

Can this part replace an optocoupler bank directly? The channel count and the logic levels usually match, but the timing does not. An optocoupler pair with a 10 microsecond rise time has no timing constraint at 1 Mbps, while this part passes at 25 Mbps and its 58 ns maximum delay changes what a controller sees at the edge. The replacement also needs a supply on the isolated side, which an optocoupler with a pull up on the far rail may not have had.

What reel size ships for the R suffix? 2000 pieces on a large reel with NiPdAu finish and a level 2 moisture rating, and the non R string ships as a 40 piece tube. Prototype quantities therefore come from the tube row or a broken reel rather than from a small reel order code.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.