Contact Us

ISO7310FCDR

Brand: Texas Instruments
Texas Instruments ISO7310FCDR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO7310FCDR — Power Management & Signal Chain | Superb Automation

ISO7310FCDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO7310FCDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO7310FCDR: single channel digital isolator with a default low output at 25 Mbps

ISO7310FCDR is a single channel digital isolator in a SOIC body of 8 pins. It passes one digital signal across a 3000 V RMS barrier at up to 25 Mbps with a filter on the input that rejects short noise pulses, and the F suffix makes the output low when the input side is unpowered. The DR order code is the eight pin SOIC on a 2500 piece reel.

Order code and package

Order codeISO7310FCDR
Package8-pin SOIC, D
Packingtape and reel, 2500 pieces
Channelsone, forward direction
Signalling rate25 Mbps
Isolation3000 V RMS for one minute per UL, 4242 V peak per VDE
Default stateoutput low when input power or signal is lost, F suffix
Supply3 V to 5.5 V on each side, level translation between rails

Electrical parameters that decide the application

Propagation delay32 ns typical at 5 V
Supply current1.9 mA at 1 Mbps and 3.8 mA at 25 Mbps on 5 V supplies
Low supply current1.4 mA at 1 Mbps and 2.6 mA at 25 Mbps on 3.3 V
Input thresholdTTL compatible
Noise filterintegrated at the input pin
Temperature rangeminus 40 to plus 125 degrees

Family variants and how they differ

ISO7310Csingle channel, default output high
ISO7310FCsingle channel, default output low, this order code
ISO7320Cdual channel, both forward
ISO7310FCDR2500 piece reel in the eight pin SOIC

Points to check before this part goes on a BOM

The F suffix is the whole point of this order code. A default low output means a loss of power on the input side pulls the output low, so a gate enable or a reset line that must fail safe in the off state needs the F part, while a signal that must fail high needs the plain ISO7310C.

The integrated noise filter at the input rejects short pulses that would otherwise cross the barrier as data. That filter also sets the minimum pulse width the part will pass, so a link carrying a very narrow strobe has to check the pulse width against the filter rather than only against the 25 Mbps rate.

Propagation delay of 32 ns typical at 5 V is what allows the part to sit in a control loop. The same signal through an optocoupler with a 100 ns to 500 ns delay adds phase lag that a current loop has to be detuned around, and that difference is usually why a part like this replaces an older coupler rather than a faster one.

Supply current is quoted per side and rises with the data rate: 1.9 mA at 1 Mbps and 3.8 mA at 25 Mbps on 5 V. A link that runs at 1 Mbps for most of its life should be specified at the 1 Mbps figure, because the isolated supply behind it is sized from the average rather than the peak.

Both sides accept 3 V to 5.5 V and translate between rails, so a 3.3 V controller can talk to a 5 V gate driver without a level shifter. The two rails are separate pins on both sides, and tying them together defeats the barrier even though the part still passes data.

An eight pin body carries one channel and one supply pair, so a two signal link needs two parts or the dual channel family. Board area is the reason the dual parts exist, and a single channel part is the cheaper choice only when the second channel is not needed.

The default state matters most at power up, before the controller has configured anything. A driver enable line that defaults high can turn a bridge on during the interval between the two supplies arriving, which is why the F part exists and why the order code has to match the signal rather than the price list.

The isolated side needs its own supply and that supply is usually a transformer driver. The current is 1.9 mA at 1 Mbps on the logic side and comparable on the isolated side, so the isolated rail is a milliampere scale load, but the rail has to be up before the signal is meaningful and its own start up time belongs in the sequencing.

An isolator in a gate drive path carries a signal that changes state only a few times per switching period, so its supply current is dominated by quiescent draw rather than by the data rate. At 1.9 mA typical on a 5 V rail the part is a 10 mW load, and the isolated supply behind it is sized by that figure plus the driver it feeds, not by the 25 Mbps headline rate.

Where this order code fits

It isolates a single control or feedback line in motor drives, power supplies, battery management, instrumentation and any board where one digital signal crosses a ground barrier. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

What does the F mean? Default output low. Without the F, the output goes high when the input side loses power, which is the wrong state for an enable or a reset line.

Does it work with 3.3 V on one side and 5 V on the other? Yes. Each side has its own supply pin from 3 V to 5.5 V and the part translates between them.

How fast can it run? 25 Mbps, but the input filter sets a minimum pulse width, so very short pulses are rejected rather than passed.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.