Contact Us

ISO7240CDWR

Brand: Texas Instruments
Texas Instruments ISO7240CDWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO7240CDWR — Power Management & Signal Chain | Superb Automation

ISO7240CDWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO7240CDWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO7240CDWR: A Quad 25 Mbps Isolator With All Four Channels Facing Forward

ISO7240CDWR is a quad-channel digital isolator in a SOIC (DW) body of 16 pins. Four channels at 25 Mbps, all in the same direction, in the same 16 pin wide body that the triple family uses, with output enables on both sides.

Order code and package

Ordering stringISO7240CDWR
PackageSOIC, 16 pins, DW body, 10.30 mm by 10.30 mm by 7.50 mm
Carrier2000 pieces on a large reel on the G4 and .A rows of the same body
Temperature rangeMinus 40 to plus 125 degrees Celsius
Part markingISO7240C
Status noteISO7240CDW tube row is printed obsolete, the DWR reel row is active
Channel directionFour channels, all forward
Default outputThe CF member holds the outputs low on input power loss
Output enableEN1 on the input side, EN2 on the output side

Electrical parameters that decide the application

Signaling rate25 Mbps on the C members
Isolation rating2500 VRMS per UL 1577
Transient isolation4000 VPK
External clearance8 mm
Channel to channel skew1 ns maximum
Pulse width distortion2 ns maximum
Barrier life25 years typical at the rated working voltage
ESD protection4 kV
Magnetic field immunity1000 A per metre
Supply range3.15 V to 5.5 V
Level translation3.3 V to 5 V in either direction
Input thresholdApproximately 1.5 V
Junction limit150 degrees
Fail state on the CF memberOutputs driven low

Family variants and how they differ

ISO7240CFour forward at 25 Mbps, this part
ISO7240CFFour forward with the outputs forced low on input power loss
ISO7240MFour forward at 150 Mbps
ISO7241CThree forward and one back at 25 Mbps
ISO7242CTwo forward and two back at 25 Mbps
ISO7740Newer 100 Mbps quad with the same channel count

Points to check before this part goes on a BOM

Four channels in one direction leaves no return path for a fault flag. A gate drive that needs a desaturation return should take the ISO7241C and give up one forward channel.

The CF member is the one to choose where an unpowered input side must produce a defined low at the output. Without the F letter the outputs sit at their normal state and a driver may see a false high.

The tube row is obsolete while the reel row is active. An engineering sample that was bought as a tube cannot be reordered as a tube, and the reel is the only published packing.

25 Mbps is the highest rate at which this family is specified. A 50 Mbps requirement moves to the ISO674x or ISO774x series, which have a different pin map.

The default low member is the one to pick when the four lines drive a power stage. A high default at power up would turn on a gate signal for as long as the controller takes to boot, which is a real hazard rather than a theoretical one.

The quad body has the same 16 pin footprint as the triple family, so a board can be laid out once and populated with either channel count. That is worth knowing when a product line uses both.

The body is the same 16 pin footprint used by the triple family, so the same board can carry either channel count. A product family that uses both should keep the two strings on one approved list.

The quad body and the triple body share the 16 pin outline, so a board can be assembled with either channel count and the same footprint. That is also the reason a wrong line item passes a visual check and fails at functional test.

The enable delay on the F member of this family is stated in microseconds, not nanoseconds. A controller that mutes the barrier and then applies a reset in the same microsecond window will still let one edge through before the outputs reach high impedance.

Four lines in one direction in a motor drive

Four forward channels cover three gate signals and one enable, or four parallel data lines in an isolated ADC interface. Both uses share the property that nothing has to come back across the barrier, which is what keeps the channel count at four rather than six.

Four forward channels in an isolated data path

An isolated analogue front end sends a serial clock, a frame sync and two data lines across the barrier, and nothing has to come back. Four forward channels in one body cover that interface, and the enable pins allow the whole path to be muted while the converter is calibrated.

The alternative is two dual isolators, which costs two packages, two sets of decoupling capacitors and a wider keep-out around the barrier. On a board where the isolated region is small, the quad part is usually the cheaper answer even at a higher unit price.

What a 25 Mbps ceiling means for a serial port

Twenty five megabits per second is a data rate, and a serial port with a clock and a frame sync consumes two channels for one byte stream. A 12 MHz clock with a data line that changes on one edge fits, and a 25 MHz clock does not, even though the number in the title looks larger than the clock.

The delay is the other half of the budget. At this rate the parts of the family are specified with skew and pulse width distortion figures that matter more than the delay itself, because a clock and its data have to arrive with the setup time the receiver expects.

Gate signals through a four channel barrier

Four forward channels map onto three gate signals and one enable, or onto four parallel data lines in an isolated converter interface. In both cases nothing returns, which is the property that keeps the channel count at four and the package at 16 pins.

The enable pins are the only way to silence the barrier without removing power. On a drive that has to hold its gates off during a fault, the enable is the pin the controller toggles, and the delay through it is much longer than the data path.

Four channels and one barrier in a drive

Three gate signals and one enable, or four parallel lines into an isolated converter, are the two patterns this part was made for. Both put the whole interface in one body, which keeps the isolated region narrow and the creepage easy to hold. The enable pins on both sides are what let the controller mute the barrier during a fault without losing the other direction.

Where this order code fits

It is used where four digital lines leave a controller and nothing has to come back, such as an isolated ADC interface or a bank of gate signals. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Incoming Inspection Plan page.

Questions buyers ask

How does ISO7240C differ from ISO7241C? The channel split. ISO7240C is four forward and ISO7241C is three forward with one reverse, on the same body and the same rate.

Why is the tube row obsolete? The vendor has consolidated this family onto tape and reel. The reel strings are active and the tube string is not, so a small quantity has to come from a broken reel.

Can this part translate 5 V to 3.3 V? Yes. Each side can sit on a different rail inside 3.15 to 5.5 V, and the part translates in either direction across the barrier.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.