ISO6720FBDR
Product Specifications
ISO6720FBDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO6720FBDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO6720FBDR: A Dual 50 Mbps Isolator With Both Channels Facing Forward and a Low Default
ISO6720FBDR is a basic dual-channel digital isolator in a SOIC (D-8) body of 8 pins. It puts two 50 Mbps channels in an eight pin body of 4.90 mm by 3.91 mm, both driving from side 1 to side 2, with the F suffix making both outputs sit low when the input side loses power, and 3000 pieces on a reel at level 2.
Order code and package
| Ordering string | ISO6720FBDR |
| Package | SOIC, 8 pins, D body, 4.90 mm by 3.91 mm nominal |
| Carrier | 3000 pieces on a large reel |
| Sibling rows | ISO6720FBDR.A at the same 3000 pieces, ISO6720BDR for the high default |
| Moisture level | Level 2, 260 C peak reflow, one year floor life |
| Lead finish | NIPDAU |
| Temperature range | Minus 40 to plus 125 degrees Celsius |
| Part marking | 6720FB |
| Tube rows | None printed in this addendum, the family ships on reel only |
| Channel direction | Two channels, both from side 1 to side 2 |
| Default output | Low, set by the F suffix |
Electrical parameters that decide the application
| Signaling rate | 50 Mbps |
| Isolation rating | 3000 VRMS per UL 1577 in the D body |
| Maximum repetitive peak voltage | 637 VPK |
| Maximum working voltage | 450 VRMS and 637 VDC |
| Maximum transient voltage | 4242 VPK |
| Maximum impulse voltage | 5000 VPK |
| Maximum surge voltage | 6500 VPK, 1.2 by 50 microsecond waveform |
| Common mode transient immunity | 150 kV per microsecond typical, 100 kV per microsecond minimum |
| Supply range | 1.71 to 1.89 V, or 2.25 to 5.5 V, set independently on each side |
| Level translation | 1.71 V to 5.5 V |
| Supply current per channel | 1.8 mA typical at 1 Mbps |
| Propagation delay | 11 ns typical, 18 ns maximum at a 5 V rail |
| Pulse width distortion | 0.2 ns typical, 7 ns maximum at a 5 V rail |
| External clearance | Above 4 mm |
| Distance through insulation | Above 17 micrometres |
| Tracking index | Above 400 V |
| ESD across the barrier | Plus or minus 8 kV IEC 61000-4-2 contact discharge |
| Barrier capacitance | About 0.5 pF from input to output |
| Enable pin | None in the eight pin body |
| Climatic category | 40/125/21, pollution degree 2 |
Family variants and how they differ
| ISO6720BDR | Both channels forward with the high default |
| ISO6721FBDR | One channel each way with the low default |
| ISO6721BDR | One channel each way with the high default |
| ISO6721RFBDR | The reversed pin arrangement with the low default |
| ISO6731FDWR | A triple at 50 Mbps with a 5000 VRMS barrier when a third line has to cross |
| ISO7641FMDWR | A quad at 150 Mbps in the wide body when the rate has to be higher |
Points to check before this part goes on a BOM
Both channels face the same way, so this part cannot carry a bidirectional line. A UART with flow control, an I2C bus or an SPI link with a return data line needs ISO6721B, which puts one channel in each direction and is the same body, the same reel and the same price band.
The eight pin body has no enable pin. Both channels run whenever both rails are above their lockout, so a system that has to park a bus during power up has to hold the far side in reset or add a buffer that can be tri-stated.
The default state is the state the output takes when the input side is unpowered, not the level the input pin is sitting at. Where a downstream gate must not fire while the rails are coming up, the low default is the safer choice and it is the reason this suffix exists.
3000 VRMS in the narrow body is a basic rating. A mains referenced circuit under the reinforced class needs the wide body parts, and the ISO672x-Q1 string named in the same document is the automotive and reinforced option rather than an equivalent of this ordering string.
1.8 mA per channel is quoted at 1 Mbps. At 50 Mbps the current follows the switching frequency and the load, so a rail budget written from the feature list will be low by a factor that has to be taken from the supply current curves.
The eight pin body is 4.90 mm by 3.91 mm, which is small enough to sit between two ground pours without moving anything else. That is the reason the family survives next to the wide body parts on boards that are already tight, and the reason a two channel requirement rarely becomes a four channel part.
Why a dual forward part survives in a market full of quads
Most isolated interfaces need two lines, not four. A converter synchronisation signal and a fault flag, a clock and a chip select, or two gate drive channels are the common cases, and an eight pin body that carries exactly two channels is cheaper in area and in cost than a quad in a wide body.
The narrow body also shortens the path between the two grounds, which helps on boards where the isolated section is a small island at the edge of the board. The trade is the 4 mm clearance and the basic rating, and both are adequate inside one enclosure.
Reading the two ratings that are easy to confuse
The 637 VPK repetitive peak figure is a continuous rating across the barrier, and the 4242 VPK transient figure is a short event. A specification that asks for a 2 kV working voltage cannot be met by this part even though its transient rating is above 4 kV, because the two numbers describe different stresses.
The 3000 VRMS one minute value is the UL 1577 withstand test, run at 1.2 times for one second on every unit and at the full value for sixty seconds on qualification. It is the number printed on the certificate, and it is the one a safety file should quote.
What the four supply options cost in practice
Each side accepts 1.71 to 1.89 V or 2.25 to 5.5 V, so a 1.8 V FPGA and a 5 V driver can share one barrier with no level shifter in between. The two ranges are selected by the rail itself and not by a pin, which keeps the eight pin body possible.
The catch is that the 1.8 V range is narrow. A rail that sits at 1.95 V is outside the low range and below the high one, so the supply has to be checked against the two windows before the part is committed, not after the first prototype.
Why the transient rating is not the working rating
The 4242 VPK transient figure describes a short event and the 450 VRMS working figure describes a continuous stress. A circuit that holds a mains derived voltage across the barrier permanently is limited by the second number, whatever the first one says.
For a mains boundary the answer is a different family, in a wider body, with a reinforced class printed on the certificate. This part is built for signals between grounds inside one piece of equipment.
Where this order code fits
It is chosen where two fast digital lines cross one barrier in one direction and the board has room for an eight pin body rather than a wide body, most often on an isolated converter or a field side driver stage. Teams comparing it with a neighbouring part start from our BOM Shortage Recovery page, and teams replacing a part that has gone end of life start from the Vendor Consolidation page.
Questions buyers ask
Can it be used for a bidirectional bus? No. Both channels drive from side 1 to side 2. The one-each-way member of the same family is ISO6721B or ISO6721FB, and it uses the same body and the same reel quantity.
What happens when the rails come up at different times? Each side has its own undervoltage lockout, and the output holds the default low until the far side is powered. That is the behaviour a gate drive wants, which is why the F suffix is the common choice for that application.
Does the reel quantity change with the suffix? No. Every industrial row of this family prints 3000 pieces on a large reel at level 2, and the suffix changes the default state or the finish paperwork rather than the packing.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.