Contact Us

ISO6441DWR

Brand: Texas Instruments
Texas Instruments ISO6441DWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO6441DWR — Power Management & Signal Chain | Superb Automation

ISO6441DWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO6441DWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO6441DWR: four digital channels, one of them reversed, at 150 Mbps

The ISO6441DWR is a four channel digital isolator with three channels in the forward direction and one in the reverse direction. It is built on a silicon dioxide barrier rated to 5000 Vrms under UL 1577, with a working voltage up to 1061 Vrms and 1500 Vdc, a surge capability of 10.4 kV, and a minimum common mode transient immunity of 200 kV per microsecond against a typical figure of 250 kV per microsecond.

The channel speed is 150 Mbps, with a maximum propagation delay of 10 ns at a 5 V supply and 12 ns at 3.3 V, and pulse width distortion of 1.8 ns at 5 V. That timing supports a serial peripheral interface at 25 MHz on a 5 V rail or 20.8 MHz on 3.3 V. The supply range is 2.25 V to 5.5 V with overvoltage tolerant inputs, and the device is offered with a default output high or, with the F suffix, a default output low.

Key data for the ISO6441DWR

ChannelsFour channels, three forward and one reverse, with output enable pins per channel group
Rate150 Mbps, serial peripheral interface to 25 MHz at 5 V and 20.8 MHz at 3.3 V
Timing10 ns maximum propagation delay at 5 V, 12 ns at 3.3 V, 1.8 ns pulse width distortion
Isolation5000 Vrms per UL 1577, 1061 Vrms working voltage, 10.4 kV surge
Immunity200 kV per microsecond minimum and 250 kV per microsecond typical common mode transient immunity
Supply2.25 V to 5.5 V on both sides, overvoltage tolerant inputs, minus 40 C to 125 C

Body, marking and reel data

BodyWide body SOIC DW, 16 pins, 10.30 mm by 10.30 mm
Reel2000 pieces on a large reel on the DWR row, 2500 on the narrow SSOP row
MarkingISO6441 printed on the body
HandlingMoisture level 2, 260 C peak, one year floor life
Functional safetyDocumentation available to support an IEC 61508 system case

Three forward and one back is the shape of a converter interface

A controller that talks to an isolated analogue front end typically sends a clock, a chip select and a data line out, and receives one data line back. Three forward and one reverse matches that exactly, which is why this channel arrangement is the most common four channel isolator. The same pattern fits a gate driver interface where three commands go out and one fault comes back.

The 10 ns delay matters when the isolated side is inside a control loop. Every nanosecond of delay eats phase margin, and a part with 30 or 40 ns of delay forces the loop bandwidth down. A 150 Mbps isolator with 10 ns of delay lets the loop run at the speed the converter would allow without isolation.

Checks before this code is bought

The first is the default state. Without the F suffix the output goes high when the input side loses power; with the F suffix it goes low. A gate drive signal that must stay off during a fault needs the low default, and a chip select that must stay inactive needs the high default. Getting this backwards turns a safe state into a commanded state.

The second is the channel direction. The 6440 is all forward, the 6441 is three forward and one back, and the 6442 is two and two. A board that needs two reverse channels cannot use this part even though the pin count and the price match.

The third is the body. The narrow SSOP row is a different creepage class from the wide body, and the safety certificate belongs to the wide body. The fourth is the supply matching: the two sides may run at different voltages within the 2.25 V to 5.5 V window, which is how a 3.3 V controller talks to a 5 V isolated stage.

Four channel isolators and the default state

The single most expensive mistake with this family is the default state, and it is a mistake that only appears in a fault. A part without the F suffix drives its outputs high when the input side loses power, and a part with the F suffix drives them low. A gate signal that must be off during a fault needs the low default, and a chip select that must stay inactive needs the high default. We ask for the safe state of every channel before quoting, and we name the suffix on the order.

The second point is the channel direction. Three forward and one back suits most converter and driver interfaces, and the two and two member covers the rest. A board that needs a second reverse channel cannot use this part, and the pin count and the price will not reveal that difference.

Where the isolator sits in a drive or a power stage, the incoming check we run is on our incoming inspection plan page. Where a long production life needs a second source qualified in advance, the method is on our supplier quality audit page.