Contact Us

ISO3088DWR

Brand: Texas Instruments
Texas Instruments ISO3088DWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO3088DWR — Power Management & Signal Chain | Superb Automation

ISO3088DWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO3088DWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO3088DWR: The 20 Mbps Half-Duplex Member of the ISO308x Isolated RS-485 Family

ISO3088DWR is an isolated half-duplex RS-485 and RS-422 transceiver in a SOIC body of 16 pins. It puts a 5 V bus-side driver and receiver behind a 2500 VRMS barrier, so a field bus that sits at a different ground potential from the controller can be read without a ground loop.

Order code and package

Ordering stringISO3088DWR
PackageSOIC, 16 pins, DW body
Body size10.30 mm by 7.50 mm, nominal
CarrierTape and reel, 330 mm reel, 16.4 mm tape, pocket 10.75 by 10.7 by 2.7 mm, pin 1 quadrant Q1
Logic-side supply3.15 V minimum to 5.5 V maximum
Bus-side supply4.5 V minimum to 5.5 V maximum
Temperature rangeminus 40 to plus 85 degrees Celsius
DuplexHalf duplex, one differential pair with DE and RE control
Family positionFastest half-duplex member, the full-duplex equivalent is ISO3086

Electrical parameters that decide the application

Signaling rate20 Mbps
Driver differential output, 54 ohm load1.5 V minimum, 2.3 V typical
Driver differential output, 100 ohm RS-422 load2 V minimum, 2.3 V typical
Driver common-mode output1 V minimum to 3 V maximum, steady-state shift within 100 mV
Receiver thresholdPlus threshold minus 85 to minus 10 mV, minus threshold minus 200 to minus 115 mV
Receiver hysteresis4 mV typical, 30 mV maximum
Bus loading1/8 unit load, up to 256 nodes on one bus
Bus input capacitance16 pF typical
Driver propagation delay25 ns typical, 45 ns maximum
Pulse width distortion3 ns typical, 9 ns maximum
Driver rise and fall time7 ns typical, 15 ns maximum
Common-mode transient immunity50 kV per microsecond, typical
ESD, bus pins to GND2plus or minus 12 kV human body model
ESD, bus pins to GND1 and all pinsplus or minus 6 kV and plus or minus 4 kV human body model, plus or minus 1 kV charged device model
Isolation rating2500 VRMS for 60 s per UL 1577, 4000 VPK basic insulation per DIN EN IEC 60747-17
Working voltage560 VPK maximum repetitive peak isolation voltage
Clearance and creepage8 mm external, material group II, comparative tracking index above 400 V
Fail-safeReceiver output high on bus open, short and idle

Family variants and how they differ

ISO3080Full duplex, 0.7 microsecond class delay, 16 pins
ISO3082Half duplex, 0.7 microsecond class delay, 16 pins
ISO3086Full duplex, 25 ns class delay, 16 pins
ISO3088Half duplex, 25 ns class delay, 16 pins, the part on this page
Delay split inside the familyThe fast pair runs 25 ns typical and 45 ns maximum against 0.7 microsecond typical and 1.3 microsecond maximum on the slow pair
Distortion split inside the family3 ns typical on the fast pair against 20 ns typical and 200 ns maximum on the slow pair
Shared across all four5 V bus side, 2500 VRMS barrier, 1/8 unit load, 16 pF bus capacitance, fail-safe receiver, thermal shutdown
Later generationISO1430 and ISO1450 move to a 5000 VRMS barrier, a 1.71 V logic side and 12 Mbps and 50 Mbps rates

Points to check before this part goes on a BOM

The bus side needs 4.5 V, the logic side does not.Two supplies are involved and only one of them is 5 V. The bus side runs from 4.5 V to 5.5 V because RS-485 levels are defined against a 5 V driver, while the logic side accepts 3.15 V to 5.5 V and the D, DE and RE inputs are 5 V tolerant, so a 3.3 V controller drives the part without a level translator.

The 256 node figure is a load figure, not a wiring allowance.One eighth of a unit load is what allows 256 receivers on one pair, but every node still adds capacitance and stub length. A 256 node bus with 1 m stubs is 256 m of copper, and the 20 Mbps rate will not survive that, so the node count and the data rate have to be traded against each other.

Half duplex means the driver has to let go.DE has to fall within one bit time of the last stop bit, or the driver holds the pair while another node starts talking. With a 45 ns maximum delay and a 50 ns bit at 20 Mbps, the firmware has to release the driver on the transmit-empty flag and not on a timer.

560 VPK is a working voltage, not a surge rating.The 4000 VPK transient and the 2500 VRMS one-minute figures are type tests. The number that governs a repeating waveform is the 560 VPK repetitive peak. A 400 V DC bus with inductive ringing that touches 600 V is outside the part, and the 5 kVRMS ISO14xx family is the correct move.

The temperature window is 85 degrees, not 125.This is the one number in the family that catches cabinet builders. A drive with the board mounted above a heatsink can sit at 90 degrees inside a 40 degree room, and the part is then outside its rated ambient while still working, which is the worst place to be.

The reel quantity is not on the row.The addendum prints the 330 mm reel and the 16.4 mm tape against ISO3088DWR but leaves the quantity column blank on that row while other rows in the same table carry 2000. Order by the full string and confirm the piece count on the reel label rather than assuming the sibling figure.

What the fail-safe receiver does on an idle bus

A terminated bus with no driver enabled sits at 0 V differential, which is inside the indeterminate window of a plain RS-485 receiver and produces random output. This part sets the output high when the differential falls below the negative threshold, so an idle bus reads as a mark and the UART sees a continuous logic high rather than noise.

That removes the external bias network on short buses. On a long bus with several terminations the bias current still has to come from somewhere, and the internal pull is weak enough that four 120 ohm terminations in parallel will hold the pair near zero, so the bias resistors stay in the circuit for multi-drop buses.

Why 16 pF of bus capacitance matters

Sixteen picofarads per node is roughly half what a standard transceiver presents, and it is the reason a 256 node bus can be discussed at all. At 20 Mbps the unit interval is 50 ns, and the rise time has to stay under about a fifth of that, which limits the total load a driver can charge.

The practical consequence is that the pin capacitance figure, not the node count, sets the cable length at the top rate. A bus that runs at 20 Mbps on 100 m will not run at 20 Mbps on 500 m even though the node count is unchanged.

Where this order code fits

Industrial drives, building automation controllers and metering concentrators use this part where the field pair is already 5 V RS-485 and the isolation is there to break a ground loop rather than to meet a 5 kV safety clause. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can ISO3088DWR replace an eight-pin 75176 socket? No. It is a 16-pin wide-body part with two supplies and a barrier in the middle, so the footprint and the power tree both change. What carries over is the logic interface and the bus behaviour, not the pad geometry.

Does the bus side work at 3.3 V? Not within specification. The bus-side minimum is 4.5 V, so a 3.3 V bus supply is outside the recommended range even though the logic side is happy at 3.3 V. The ISO14xx family is the one with a 3 V bus-side floor.

Is external fail-safe biasing still needed? On a two-node bench bus, no. On a multi-drop bus with several terminations, yes, because the internal pull cannot hold a heavily terminated pair above the threshold when every driver is off.

What happens if the bus side loses power while the logic side stays alive? The receiver output goes to its fail-safe state and the bus pins go high impedance. The part does not present a load to the live side, which is the property that lets a hot-swapped module be pulled without dragging the bus down.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.