ISO1640QDWRQ1
Product Specifications
ISO1640QDWRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO1640QDWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO1640QDWRQ1: The Automotive I2C Isolator That Lets a Bus Keep Talking Through a Hot Swap
ISO1640QDWRQ1 is an automotive qualified hot-swappable bidirectional I2C isolator in a SOIC (DW) body of 16 pins. It carries SDA and SCL as two bidirectional open-drain channels at up to 1.7 MHz, and the I2C protocol logic sits inside the part, so a floating measurement side can be joined to a controller side without a bridging buffer and without the bus lock-up an optocoupler pair usually brings.
Order code and package
| Ordering string | ISO1640QDWRQ1 |
| Family and grade | ISO164x, the automotive string of the hot-swappable I2C isolator |
| Package | SOIC, 16 pins, DW body, 10.30 mm by 7.50 mm nominal |
| Reel and packing | Not printed in SLLSFC2D; the industrial DW row reads 2000 pieces on a large reel, confirm the automotive row on the Q1 addendum and on the label |
| Industrial reference rows | ISO1640DWR at 2000 pieces on a large reel, level 2 260 C, one year floor life, marking ISO1640 |
| Temperature range | Minus 40 to plus 125 degrees Celsius on the printed rows |
| Channel structure | Two bidirectional open-drain channels, one for SDA and one for SCL |
| Watchdog state | The outputs follow the bus on both sides, there is no default level to set |
| Hot swap | Bus pins tolerate 0 to 6 V while either side is unpowered |
Electrical parameters that decide the application
| Bidirectional data rate | Up to 1.7 MHz on SDA and SCL, set by the RC time constant of the bus |
| Unidirectional channel rate | 50 Mbps on the GPIO channels of the ISO1642, ISO1643 and ISO1644 members |
| Isolation rating | 5000 VRMS per UL 1577 in the DW body |
| Maximum repetitive peak voltage | 2121 VPK in the DW body |
| Maximum working voltage | 1500 VRMS and 2121 VDC in the DW body |
| Maximum transient voltage | 7071 VPK, tested at 1.2 times for one second on every unit and at the full value for sixty seconds on qualification |
| Maximum surge voltage | 6500 VPK basic and 10000 VPK reinforced, 1.2 by 50 microsecond waveform |
| Common mode transient immunity | Plus or minus 100 kV per microsecond typical |
| ESD on the bus pins | Plus or minus 10 kV human body model on side 1, plus or minus 14 kV on side 2, plus or minus 1500 V charged device model |
| ESD across the barrier | Plus or minus 8 kV IEC 61000-4-2 contact discharge with all pins of each side tied together |
| Side 1 supply | 3.0 to 5.5 V |
| Side 2 supply | 2.25 to 5.5 V |
| Sink capability | 3.5 mA on side 1 and 50 mA on side 2, as printed in the feature list |
| Capacitive load | 80 pF on side 1 and 400 pF on side 2, as printed in the feature list |
| Propagation, side 1 to side 2 | 20 ns typical and 30 ns maximum rising, 80 ns typical and 130 ns maximum falling |
| Propagation, side 2 to side 1 | 40 ns typical and 48 ns maximum rising, 70 ns typical and 100 ns maximum falling |
| Round trip on side 1 | 62 to 74 ns with a 40 pF local load and a 400 pF remote load |
| Undervoltage lockout | 2.7 V rising on side 1 and 2.3 V rising on side 2, with 100 to 150 mV of hysteresis |
| External clearance | Above 8 mm, with more than 17 micrometres of insulation through the barrier |
| Tracking index | Above 600 V, material group I, pollution degree 2 |
| Junction to ambient | 62.4 degrees per watt in the DW body |
Family variants and how they differ
| ISO1640DWR | The industrial string of the same die, printed at 2000 pieces on a large reel with marking ISO1640 |
| ISO1640BDR | The eight pin basic version, 3000 VRMS, 3000 pieces on a reel, marking 1640B |
| ISO1641DWR | One bidirectional data channel and one unidirectional clock channel, for a bus that only ever clocks one way |
| ISO1642DWR and ISO1643DWR | The same I2C pair with two unidirectional CMOS channels added for static signals |
| ISO1644DWR | The I2C pair with three unidirectional channels, enough to carry an isolated SPI link beside the bus |
| ISO6721BDR | A plain digital dual at 50 Mbps when the I2C protocol logic is not needed |
| ISO6741FDWR | A 50 Mbps quad with three forward and one reverse channel for wider buses |
Points to check before this part goes on a BOM
The Q1 rows are not printed in SLLSFC2D. The document covers ISO1640, ISO1641, ISO1642, ISO1643 and ISO1644 and its addendum lists the industrial and B strings only, so the automotive reel quantity, the moisture level and the marking have to be read from the Q1 addendum or the reel label rather than copied from the ISO1640DWR row.
The two sides are not symmetric. Side 1 runs from 3.0 to 5.5 V and side 2 from 2.25 to 5.5 V, so a 1.8 V sensor hub cannot sit on side 1 even though it can sit on side 2. Boards that assume a symmetric supply range have to be rechecked before this part is dropped in.
The propagation figures are asymmetric by nature. A rising edge crossing from side 1 to side 2 takes 30 ns at the maximum while a falling edge takes 130 ns, which is 100 ns of pulse width distortion on a bus that stretches the clock. The clock low period in the timing budget has to include that skew.
1.7 MHz is a ceiling that depends on the bus, not a promise. The table notes that the maximum frequency follows the RC time constant, and the capacitive load limits of 80 pF on side 1 and 400 pF on side 2 are the numbers that decide whether the bus reaches the ceiling at all.
Hot swap is a supply condition, not a data condition. The absolute maximum table allows 0 to 6 V on the bus pins while the part is unpowered, which is what keeps a card insertion from latching the bus. That tolerance is on the I2C pins only, not on the supply pins or on the GPIO channels.
Where the two sides sit in a telematics unit
A telematics board usually keeps its cellular and GNSS section on one ground and its vehicle interface on another, and an I2C temperature sensor or an EEPROM often sits on the far side of that split. The ISO164x puts the protocol logic on the isolated side, so the controller keeps using the same bus calls and the only change is the extra supply rail for the floating section.
The automotive string matters where the board is qualified to a vehicle programme rather than to an industrial cabinet. The silicon is the same bidirectional channel, and the difference sits in the qualification paperwork, the temperature grade and the reel, which is why the ordering string has to be quoted exactly and not shortened to ISO1640.
What the second supply rail costs
Each side needs its own decoupling and its own rail, and the far side normally needs an isolated converter to feed it. That converter is the real cost of the barrier, and it is the reason an interface that only needs one signal isolated often moves to a single-channel digital isolator instead.
Where the far side already has a local supply, the rail problem disappears and the isolator is the only added part. Battery management and motor control boards usually fall in that group, because the high side already carries its own regulator for the gate drive.
Where this order code fits
The barrier is chosen when a controller on a vehicle ground has to read an I2C sensor on a floating or hot-swappable board, and the bus has to survive the card being pulled and reinserted while the rest of the system stays powered. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
Is the automotive string pin compatible with the industrial one? It uses the same sixteen pin wide body and the same channel arrangement, so the footprint matches. The supply range, the isolation ratings and the temperature grade follow the automotive document, and that document is not the one that carries the electrical tables here.
Can this replace a pair of optocouplers on an I2C bus? Yes, and it removes the external logic that an optocoupler pair needs to handle the bidirectional handshake. The open-drain outputs sink 3.5 mA on side 1 and 50 mA on side 2, so the pull-up values have to be chosen against those currents rather than against the optocoupler drive.
What happens if side 1 is powered and side 2 is not? Side 2 stays locked out below its 2.3 V threshold and the bus on that side is left alone. Once the rail rises the channels start passing data again, and the hot swap tolerance means the unpowered side can sit at any level between 0 and 6 V without damage.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.