Contact Us

ISO1640BDR

Brand: Texas Instruments
Texas Instruments ISO1640BDR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO1640BDR — Power Management & Signal Chain | Superb Automation

ISO1640BDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO1640BDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO1640BDR: The Eight Pin I2C Isolator With a 3000 VRMS Barrier

ISO1640BDR is a basic bidirectional I2C isolator in a SOIC (D-8) body of 8 pins. It puts the same hot-swappable SDA and SCL channels as the wide body part into an eight pin body of 4.90 mm by 3.91 mm, at 3000 VRMS and 3000 pieces on a reel, which is the version most boards take when the barrier only has to be basic.

Order code and package

Ordering stringISO1640BDR
PackageSOIC, 8 pins, D body, 4.90 mm by 3.91 mm nominal
Carrier3000 pieces on a large reel
Sibling rowsISO1640BDR.A and ISO1640BDRG4 at the same 3000 pieces and the same marking
Moisture levelLevel 2, 260 C peak reflow, one year floor life
Lead finishNIPDAU
Temperature rangeMinus 40 to plus 125 degrees Celsius
Part marking1640B
Tube rowsNone printed for the eight pin body, it ships on reel only
Channel structureTwo bidirectional open-drain channels

Electrical parameters that decide the application

Bidirectional data rateUp to 1.7 MHz, set by the bus RC time constant
Isolation rating3000 VRMS per UL 1577 in the D body
Basic protection classPrinted as basic insulation for this body, the reinforced class belongs to the DW string
Maximum repetitive peak voltage637 VPK in the D body
Maximum working voltage450 VRMS and 637 VDC in the D body
Maximum transient voltage4242 VPK in the D body
Maximum surge voltage5000 VPK in the D body
Common mode transient immunityPlus or minus 100 kV per microsecond typical
ESD on the bus pinsPlus or minus 10 kV human body model on side 1, plus or minus 14 kV on side 2
ESD across the barrierPlus or minus 8 kV IEC 61000-4-2 contact discharge
Side 1 supply3.0 to 5.5 V
Side 2 supply2.25 to 5.5 V
Sink capability3.5 mA on side 1 and 50 mA on side 2, per the feature list
Capacitive load80 pF on side 1 and 400 pF on side 2
Propagation20 ns typical rising and 80 ns typical falling from side 1 to side 2, 40 ns and 70 ns from side 2 to side 1
Undervoltage lockout2.7 V rising on side 1 and 2.3 V rising on side 2
External clearance4 mm in the eight pin body, with more than 17 micrometres of insulation
Tracking indexAbove 400 V, material group II, for this body
Junction to ambient106.3 degrees per watt in the eight pin body

Family variants and how they differ

ISO1640DWRThe sixteen pin version with the 5000 VRMS reinforced barrier
ISO1641BDROne bidirectional data channel and one unidirectional clock channel in the same body
ISO1640DWR.AThe wide body string at 2000 pieces with the alternate finish paperwork
ISO6721BDRA plain digital dual at 50 Mbps when the I2C protocol logic is not needed
ISO6731FDWRA triple at 50 Mbps with a 5000 VRMS barrier when the bus grows to three lines
ISO7741FDWRA quad at 100 Mbps when the barrier has to be reinforced and wider

Points to check before this part goes on a BOM

3000 VRMS in an eight pin body is a basic isolation rating. Anywhere the barrier has to hold off a mains referenced circuit under the reinforced class, the sixteen pin DW string is the one to quote, and the two are not interchangeable on a certificate even though the silicon behaves the same.

The eight pin body has no GPIO channels. The ISO1642, ISO1643 and ISO1644 members add two or three unidirectional CMOS channels for static signals, and they only exist in the sixteen pin body, so a board that needs one alarm line across the barrier cannot use this part.

Clearance drops from more than 8 mm to 4 mm when the body shrinks. That is the number a safety reviewer will read, and it follows the package rather than the ordering string, so the board spacing has to be checked before the smaller body is chosen for space reasons.

The sink capability of 50 mA on side 2 is far higher than an I2C bus needs. It is there so the part can drive a long or heavily loaded bus without an external buffer, and it is also why a short on that side is limited by the part rather than by the pull-up.

The reel of 3000 is the smallest buy in this family. A first article build of a few hundred boards usually takes the tube or a cut tape from stock rather than opening a full reel.

Where the small body wins

A sensor card that has to be isolated from a backplane often has very little room, and the eight pin body saves more than half the board area of the wide version. When the barrier only has to separate two low voltage grounds inside one enclosure, the basic rating is enough and the small body is the cheaper answer on both count and area.

The trade is the clearance and the missing GPIO channels. Boards that later need a third line across the barrier have to move to the wide body, and that move usually costs a board revision rather than a component change.

Reading the propagation pair correctly

The rising edge from side 1 to side 2 is quoted at 20 ns typical and the falling edge at 80 ns typical, and the mismatch is inherent to the open-drain structure. On a clock line this shows up as a duty cycle that is not 50 per cent at the far end, and the receiving device has to be checked against the minimum high and low times rather than against the nominal frequency.

The reverse direction is faster on the rise and slower on the fall in the same proportion. A bus that carries a clock in one direction only should still be checked in the direction it actually runs, because the two directions are not the same channel.

Where the part sits on a sensor card

A sensor card that plugs into a backplane usually keeps its analog front end on the card ground and talks to the host over a short I2C bus. The eight pin part sits between the two grounds, and the only extra components are two pull-up pairs and the decoupling for the far side rail.

Because the part carries the protocol logic, the host firmware does not change. That is the practical argument for the family over an optocoupler pair, which needs a bridging buffer on the floating side and a second supply for it.

Where the basic class is not enough

A card that sits inside one enclosure on two low voltage grounds is a basic class application. The moment one of those grounds is tied to a mains referenced circuit, the same board needs the reinforced string in the wide body, and the certificate has to name the wider part.

The silicon behaves the same in both cases. What changes is the printed class, the clearance and the package, and those three are what a safety reviewer reads before the board is accepted.

Where this order code fits

It is chosen where a compact module has to keep an I2C sensor on a separate ground and the barrier only needs the basic class, most often inside one enclosure rather than across a mains boundary. Teams comparing it with a neighbouring part start from our How to Verify a Drop in Replacement page, and teams replacing a part that has gone end of life start from the Incoming Inspection Plan page.

Questions buyers ask

Can this replace a wide body part without a board change? No. The eight pin body has a different footprint and a 4 mm clearance instead of more than 8 mm, so the board has to change. The pin functions are also reduced, because this body carries no GPIO channels.

What is the difference between this and the DW string electrically? The bus behaviour is the same, at up to 1.7 MHz with the same two supply ranges. The barrier rating, the clearance and the isolation class differ, and those are the numbers a safety file is written against.

Is the reel quantity the same for the G4 rows? Yes. ISO1640BDR, ISO1640BDR.A and ISO1640BDRG4 all print 3000 pieces on a large reel with the same marking, so the suffix changes the finish paperwork rather than the packing.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Date Code Management page sets out the checks that keep a substitute from failing on the bench.