Contact Us

INA293A1IDBVR

Brand: Texas Instruments
Texas Instruments INA293A1IDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA293A1IDBVR — Power Management & Signal Chain | Superb Automation

INA293A1IDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA293A1IDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA293A1IDBVR: 110 V, 1.3 MHz current sense amplifier at 20 V per volt in the five pin SOT-23

INA293A1IDBVR is a high side current sense amplifier that measures a shunt drop on a common mode anywhere from 4 V below ground to 110 V, independent of its own supply in a SOT-23 body of 5 pins. It runs from a single 2.7 V to 20 V supply, draws 1.5 mA, and delivers a fixed 20 V per volt gain with 0.15 per cent of gain error and 50 uV of offset at the top of the limit. The common mode window reaches 110 V in operation and survives 120 V, and the amplifier holds 1.3 MHz of bandwidth with a 2.5 V per microsecond slew rate.

Order code and package

INA293A1IDBVRSOT-23 DBV body, 5 pins, 3000 pieces on a large reel, Active, RoHS Yes, NIPDAU finish, moisture level 1 with unlimited floor life, part marking 1XWC, minus 40 to plus 125 degrees
INA293A1IDBVRG4the same DBV body with the same NIPDAU finish and moisture level 1, a second row of the same addendum
INA293A1IDBVRG4 reel notethe reel table at the back of the document prints the G4 string at 250 pieces on a small reel while the base string is printed at 3000, so the quantity column has to be read per row rather than assumed from the R suffix
INA293B1IDBVRthe second pin-out variant at the same 20 V per volt gain, a separate order code and not an accuracy grade
Other gainsthe A2 to A5 and B2 to B5 strings move to 50, 100, 200 and 500 V per volt in the same five pin body

Electrical parameters that decide the application

Common mode rangeminus 4 V to 110 V in operation, minus 20 V to 120 V survival, independent of the supply voltage
Gain20 V per volt on this member, with 50, 100, 200 and 500 V per volt in the same family
Gain error0.02 per cent typical and 0.15 per cent maximum from 50 mV above ground to 200 mV below the supply, gain drift 10 ppm per degree maximum
Offset voltage30 uV typical and 50 uV maximum on this member, tightening to 2 uV typical on the 500 V per volt member because the input referred offset divides by the gain
Offset drift0.05 uV per degree typical and 0.5 uV per degree maximum on the three lower gain members, halving on the 200 and 500 V per volt parts
Common mode rejection160 dB at DC and 85 dB at 50 kHz, which is the number that matters on a switching node
Power supply rejection1 uV per volt typical and 8 uV per volt maximum on this member, referred to the input
Input bias current10 uA typical and 30 uA maximum on both input pins, which is large against the instrumentation amplifiers in this band and has to be allowed for in the shunt value
Bandwidth1300 kHz on the 20 V per volt member, 1000 kHz on the 50 V per volt member, 900 kHz on the 100 V per volt member
Slew rate and load2.5 V per microsecond, 500 pF of load without an isolation resistor and no sustained oscillation
Output swingto within 70 mV typical and 150 mV maximum of the supply rail, and to within 5 mV typical of ground
Supply and current2.7 V to 20 V, 1.5 mA of quiescent current, specified from minus 40 to plus 125 degrees

Family variants and how they differ

A against Bin the INA293 the letter is a pin-out variant and not an accuracy grade, so INA293A1 and INA293B1 are both 20 V per volt with the same limits and only the pin assignment changes
Gain against offsetthe same die serves five gains, so the input referred offset falls as the gain rises: 50 uV maximum at 20 V per volt, 2 uV typical at 500 V per volt, which is the reason a low current measurement is often built on the highest gain member
INA293 against INA241the INA241 adds bidirectional operation, a 10 uV offset limit and enhanced rejection of switching common mode, at 2.5 mA of supply current instead of 1.5 mA
INA293 against INA180the INA180 is a 5.5 V common mode part in the same five pin body, so a board that moves from a 5 V rail to a 48 V rail keeps the footprint but not the part
Common mode below groundthe minus 4 V operating window is what allows the part to sit on a half bridge source and read recirculating current through a freewheel diode without a level shift

Points to check before this part goes on a BOM

The negative common mode range is the feature that separates this part from a plain high side amplifier. A half bridge pulls its source node below ground on every switching edge, and an amplifier that stops at 0 V either clips or needs a clamp, while this one keeps measuring to minus 4 V. That is what makes it usable in a motor phase or a synchronous converter rather than only in a battery line.

The 30 uA of input bias current is large for a shunt amplifier and it has to be spent against the shunt value. On a 1 milliohm shunt that is 30 nV of offset, which is nothing, but the bias current also has to come from the source, and a 100 Ohm filter resistor between the shunt and the input pin adds 3 mV of drop. The filter resistor is the usual place this current is forgotten.

The gain error window is 0.15 per cent maximum but it is specified between 50 mV above ground and 200 mV below the supply. A 20 V per volt part with a 5 mV shunt signal produces 100 mV at the output and sits inside the window, while a 5 V supply and a 100 mV output leaves only 4.9 V of headroom, so the output stage is not the limit. What does limit a small signal is the 50 uV offset, which is 2.5 mV at the output.

The 160 dB of DC rejection is not a guarantee at frequency. At 50 kHz the figure is 85 dB, which on a 48 V switching node with a 100 ns edge still couples a transient into the output. The INA241 exists for exactly that case and quotes 104 dB at 100 kHz, so the choice between the two is a switching frequency question more than an accuracy question.

The five pin body has no filter pin and no reference pin. The output is referred to ground, it swings to within 150 mV of the supply, and any offset the host wants to add has to come from a second amplifier. That is the trade for the 2.9 mm by 1.6 mm footprint.

The 500 pF load limit is quoted with no isolation resistor, which is generous for a 1.3 MHz part, but a converter input is a switched capacitor rather than a capacitor, and the charge injection appears as a step the amplifier has to absorb. A 50 Ohm series resistor keeps the loop stable and costs nothing in a DC measurement.

Why the highest gain member is often the quietest

Input referred offset is the output offset divided by the gain, so the 500 V per volt member turns the same 2 uV of input offset into 1 mV at the output while the 20 V per volt member turns 50 uV into 1 mV. The two arrive at a similar output error from very different input limits, which is why the highest gain that still fits the current range is usually the right choice rather than the middle one.

Shunt and filter values that keep the reading honest

A 1 milliohm shunt at 20 A dissipates 400 mW and produces 20 mV, which is 400 mV at the output of this member. That is a comfortable 0.4 per cent of a 5 V rail, and the 50 uV offset is 0.25 per cent of the shunt drop. Halving the shunt to 0.5 milliohm doubles both percentages, so the shunt value decides whether the offset or the gain error dominates.

The differential filter across the input pins should be built from two equal resistors of 10 to 100 Ohm and a capacitor of 100 nF or less, because the bias current flows through those resistors and any mismatch turns it into a differential error. Two resistors from one reel are the practical answer, not two from different reels.

Where this order code fits

Active antenna systems, motor phase current sensing, solenoid and actuator drives, telecom rectifiers and battery management are the applications the vendor names, and each of them has a common mode that moves faster than the current being measured. Teams comparing it with a neighbouring part start from our Amplifier Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Is the A suffix an accuracy grade? No. In the INA293 the A and B strings are pin-out variants at the same gain and the same limits, unlike the INA241 where A and B are accuracy grades.

Can it measure current in a 48 V rail? Yes. The operating common mode reaches 110 V and survives 120 V, while the supply itself only has to be 2.7 V to 20 V.

What happens below ground? It keeps measuring to minus 4 V, which is why the part suits half bridge source nodes that ring below ground on each edge.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.