Contact Us

INA241A3IDGKR

Brand: Texas Instruments
Texas Instruments INA241A3IDGKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA241A3IDGKR — Power Management & Signal Chain | Superb Automation

INA241A3IDGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA241A3IDGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA241A3IDGKR: 50 V/V for the middle of a current range

The INA241A3IDGKR is the 50 V/V member of the INA241A family in the 8 pin VSSOP body. It sits between the 20 V/V part that suits a high current phase and the 100 V/V part that suits a lower current one, and it exists because most motor and solenoid applications want a shunt that dissipates a few hundred milliwatts rather than a few watts. At 50 V/V a 0.5 milliohm shunt gives 25 mV per amp, so a 20 A phase produces 500 mV and a 3.3 V converter reads it with the output comfortably inside its swing.

The accuracy rows are the A tier: 10 uV maximum offset, 0.1 uV per degree, 0.01 percent maximum gain error and 1 ppm per degree of gain drift. On a 500 mV signal the gain error is 50 uV, which is the same order as the offset, so the two error terms are balanced rather than one hiding the other. That balance is usually what makes a mid gain part the easiest to specify without a calibration step.

Key data for the INA241A3IDGKR

Gain50 V/V fixed, one of five options from 10 to 200 V/V in the same family
Common modeMinus 5 V to 110 V operational, minus 20 V to 120 V survival, independent of the 2.7 V to 20 V supply
AccuracyOffset 10 uV maximum with 0.1 uV per degree, gain error 0.01 percent maximum with 1 ppm per degree
Rejection166 dB DC typical, 104 dB at 100 kHz, 89 dB at 1 MHz, with PWM rejection to 125 kHz
Speed1.1 MHz at every gain, 8 V per microsecond slew, 1 us settling to 1 percent
Supply2.7 V to 20 V, 2.5 mA typical and 3 mA maximum, minus 40 C to 125 C ambient

Body, marking and reel data

BodyDGK, 8 pin VSSOP at 3 mm by 4.9 mm, 0.65 mm pitch
Reel2500 pieces on a large reel for the DGK rows of this family
FinishNIPDAU at moisture level 2, one year floor life, bake required after the floor time is exceeded
Marking2U8B on this gain and body, which does not encode the gain in readable form
Tier splitThe B tier with the same 50 V/V gain carries 150 uV offset and 0.1 percent gain error at a lower price

Where 50 V/V is the comfortable middle

Solenoid and valve control is the clearest case. A valve driver runs at 2 A to 10 A, needs the current to be measured to a few percent for force control, and wants the shunt small because the coil is already hot. With a 1 milliohm shunt and 50 V/V, 8 A gives 400 mV, which is 80 times the offset floor and still well inside the output swing on a 5 V rail.

The same gain suits a battery disconnect or a precharge circuit where the current ramps to tens of amps and then falls to milliamps once the load is charged. A 20 V/V part would sit too close to the offset at the low end of that ramp; a 100 V/V part would clip at the top. Where the board has to cover both ends, the usual answer is two parts on two shunts rather than one part with a switchable gain, and the amplifier cross reference note lists the gain options with their respective swings so the split can be chosen on paper. Where a shortage forces a gain change late in a build, the BOM shortage recovery note covers what a gain substitution does to the calibration constants.

Buyer questions on the INA241A3IDGKR

Can a gain substitution be made without a board change? Yes within this family, because all five gains share the pinout. The host calibration constants change, and the measurable current range changes, so the host software has to be re-checked even though the hardware is untouched.

Is the 110 V common mode rating the same at every gain? Yes. The gain stage is after the input stage, so the common mode window does not shrink as the gain rises.

Why does the offset matter at 50 V/V? Because the offset is referred to the input. At 50 V/V, 10 uV of offset is 500 uV at the output, which on a 400 mV signal is a tenth of a percent of full scale and therefore comparable to the gain error.

Availability and ordering notes

The DGK rows of this family are active at 2500 pieces on a large reel at moisture level 2. Two practical notes apply to every gain in this table. The ordering columns are printed one row out of step with the part numbers in this revision, so the body and the reel have to be read from the decode rather than from the adjacent cell. And the body marking names the gain but not the accuracy tier, so an A3 and a B3 in the same gain cannot be separated after reflow. We hold the tiers on separate reels and separate labels, and a buffer of the A tier against a programme that cannot accept the looser part is planned on the safety stock planning sheet.